游梁式抽油机间歇供电装置的研制与应用

针对游梁抽油机电动机效率低和井场窃电问题,研制了具有节电和防井场窃电功能的游梁抽油机调压+间歇供电装置。该装置通过控制可控硅的导通角实现在电动机做功期调压供电,在电动机发电期不供电。分析了间歇供电对电动机、抽油机和电网的影响;根据现场实测数据分析了该装置的节电效果及现场应用情况。该装置节电效果显著,能防止井场窃电,可用于对游梁抽油机电动机的长期驱动。     

摩擦换向抽油机悬点运动分析计算

摩擦换向抽油机采用开关磁阻电动机或变频调速电动机,其特点是可以频繁双向旋转,带动摩擦轮正反转,实现光杆的上行下行。该抽油机运动特点与游梁式抽油机运动特点有较大区别,文章分析了摩擦换向抽油机的运动特点,给出了该机悬点位移、速度、加速度的计算方法。     

Chemische Zusammensetzung und Mikrostruktur polymerabgeleiteter Gläser und Keramiken im System Si–C–O. Teil 2: Charakterisierung der Gefügeausbildung mittels hochauflösender Durchstrahlungselektronenmikroskopie und Feinbereichsbeugung

Chemical Composition and Microstructure of Polymer‐Derived Glasses and Ceramics in the Si–C–O System. Part 2: Characterization of microstructure formation by means of high‐resolution transmission electron microscopy and selected area diffraction Liquid or solid silicone resins represent the economically most interesting class of organic precursors for the pyrolytic production of glass and ceramics materials on silicon basis. As dense, dimensionally stable components can be cost‐effectively achieved by admixing reactive filler powders, chemical composition and microstructure development of the polymer‐derived residues must be exactly known during thermal decomposition. Thus, in the present work, glasses and ceramics produced by pyrolysis of the model precursor polymethylsiloxane at temperatures from 525 to 1550 °C are investigated. In part 1, by means of analytical electron microscopy, the bonding state of silicon was determined on a nanometre scale and the phase separation of the metastable Si–C–O matrix into SiO₂, C and SiC was proved. The in‐situ crystallization could be considerably accelerated by adding fine‐grained powder of inert fillers, such as Al₂O₃ or SiC, which permits effective process control. In part 2, the microstructure is characterized by high‐resolution transmission electron microscopy and selected area diffraction. Turbostratic carbon and cubic β‐SiC precipitate as crystallization products. Theses phases are embedded in an amorphous matrix. Inert fillers reduce the crystallization temperature by several hundred °C. In this case, the polymer‐derived Si–C–O material acts as a binding agent between the powder particles. Reaction layer formation does not occur. On the investigated pyrolysis conditions, no crystallization of SiO₂ was observed.     

游梁式抽油机二次平衡分析

为解决游梁式抽油机能耗大、效率低的问题，设计了二次平衡装置。这种装置通过是挂在抽油机后端的平衡重的平衡作用，降低一次平衡曲柄轴净扭矩的两个峰值，达到减少能耗提高效率的目的。对抽油机的二次平衡作了较详尽的理论分析，给出了实行二次平衡后曲柄轴净扭矩的计算公式和安装二次平衡装置前后曲柄轴净扭矩曲线图。在大庆油田两口井上进行的现场试验结果表明，安装二次平衡装置后，两口井年节约电费分别为0.25万元和1．17万元，经济效益明显。     

Biodegradation of monoaromatic hydrocarbons in aquifer columns amended with hydrogen peroxide and nitrate

The ability of indigenous microorganisms to degrade benzene, toluene, ethylbenzene and xylenes (BTEX) in laboratory scale flow-through aquifer columns was tested separately with hydrogen peroxide (110 mg/l) and nitrate (330 mg/l as NO₃⁻) amendments to air-saturated influent nutrient solution. The continuous removal of individual components from all columns relative to the sterile controls provided evidence for biodegradation. In the presence of hydrogen peroxide, the indigeneous microorganisms degraded benzene and toluene (> 95%), meta- plus para-xylene (80%) and ortho-xylene (70%). Nitrate addition resulted in 90% removal of toluene and 25% removal of ortho-xylene. However, benzene, ethylbenzene, meta- and para-xylene concentrations were not significantly reduced after 42 days of operation. Following this experiment, low dissolved oxygen (< 1 mg/l) conditions were initiated with the nitrate-amended column influent in order to mimic contaminated groundwater conditions distal from a nutrient injection well. Toluene continued to be effectively degraded (> 90%), and more than 25% of the benzene, 40% of the ethylbenzene, 50% of the meta- plus para-xylenes and 60% of the ortho-xylene were removed after several months of operation.     

High temperature controlled atmosphere experiments for catalysts in a transmission electron microscope

A new transmission electron microscopy (TEM) specimen preparation procedure for high temperature experiments using a controlled atmosphere specimen holder (HTCASH) has been developed. It is designed for studying the microstructure of catalyst specimens before and after treatments in various gases. The procedure involved (1) finding a new formula for the embedding material, (2) devising a new method of making specimen supports, and (3) developing a method for removing the embedding material after the specimen has been microtomed. These techniques were then brought together to produce the ideal specimens for the HTCASH experiments. As an extra benefit, this procedure is also suitable for preparing specimens for ultrahigh resolution imaging experiments. The application of the new procedure in HTCASH experiments is illustrated through a high temperature reduction of a Co/SiO₂-923 catalyst.     

直线式电机在有杆抽油设备中的应用

通过对游梁式抽油机的效率、启动特性与直线式电机驱动的有杆抽油机特性的对比，论述了直线抽油机的优越性及应用前景。     

Influence of Edible Films upon the Moisture Loss and Microstructure of Dietetic Sucrose-Free Sponge Cakes during Storage

The kinetics of changes in the bound water content in dietetic sucrose-free sponge cakes (DC) during storage was investigated. The effect of edible films of polymyxan, pectin, xanthan, and carboxymethylcellulose upon this kinetics was also investigated. The quantitative changes in both states of water (slightly bound water and strongly bound water) were registered by combined dynamic analysis (thermogravimetry analysis, TGA, and differential thermal analysis, DTA). The moisture changes in DC crumb were analyzed by drying out to constant mass. The rate constants were determined according the equation q = q_oe^-kt. The values of rate constants 'k', in day^-1, concerning the different edible films were as follows: for crumb moisture is (8.00 ≤ k ≤ 12.47) × 10^-3, for bound water is (3.07 ≤ k_w ≤ 6.26) × 10^-2, for slightly bound water is (4.22 ≤ k₁ ≤ 8.49) × 10^-2 and for strongly bound water is (2.02 ≤ k₂ ≤ 5.62) × 10^-2 as compared to 18.53 × 10^-3, 7.16 × 10^-2, 9.04 × 10^-2, and 5.36 × 10^-2 in the uncovered DC, respectively. The best water-retaining effect in respect to crumb moisture during storage was ascertained in the use of polymyxan and xanthan films. The lowest rate constant values for bound water and its two states were measured for DC covered with pectin. The relation between the kinetics of both bound water states during storage and ageing of the crumb of DC covered with different edible films and the crumb microstructure was represented. By means of scanning electron microscope was read the smallest change in crumb microstructure of pectin-covered DC on the sixth day of storage.     

Influence of accelerated ageing on methacrylate‐based denture resins heterogeneity as viewed by ESR‐spin‐probe method

The electron‐spin‐resonance (ESR) spin‐probe method, was used to study the heterogeneity of denture resins based on poly(methyl methacrylate). Results for three resins processed by microwave energy, conventional curing and cold curing (depending on the curing procedure and exposed to ageing in various environmental conditions) were compared. All three cured resins were stored over the same time (1200 h) in distilled water at ambient temperature and in artificial saliva at 348 K. The temperature‐dependent ESR spectra of a spin probe dispersed in the denture resins are analyzed in terms of line‐shapes and line‐widths. The appearance of two spectral components was taken as an indication of resin heterogeneity. The results reveal that the cold‐cured resin has a lower local density in comparison with microwave and conventionally cured resin. The amount of residual monomer also contributes to the local motion of polymer segments. The change of denture resins exposed to ageing is influenced both by the structure of the original resin and the ageing conditions. Restricted motion of a spin probe incorporated into the acrylic resins exposed to accelerated ageing suggests additional crosslinking of polymer chains. The differences are observed for all the investigated resins, but the highest change is observed with the cold‐cured resin. The ESR results are accompanied by T_g and T_m measurements. Copyright © 2005 Society of Chemical Industry     

A simple handling technique for mammalian oocytes and embryos during preparation for transmission electron microscopy

Due to their small size, mammalian oocytes and embryos pose unique problems during preparation for transmission electron microscopy. This paper outlines a method which combines protein embedding with centrifugation to locate the specimens on the face of a Beem capsule mould. This method facilitates both the processing of oocytes with minimal loss and rapid location of the specimens within the block for simultaneous sectioning, staining and examination.