宝浪油田侏罗系三工河组浅水辫状河三角洲沉积模式研究

焉耆盆地侏罗系三工河组广泛发育由辫状河进积到湖泊中形成的辫状河三角洲。这种三角洲特征显著不同于其它三角洲,其主体是辫状分流河道和水下分流河道。宝浪油田含油层段主体为辫状分流河道,以心滩发育为主要特征,是典型的浅水缓坡粗粒辫状河三角洲沉积。     

气力输送在烧结电除尘输灰系统中的应用

针对烧结厂烧结电除尘灰的工况特性，介绍了输送烧结电除尘灰的正压气力输灰系统的特点、组成，还对在调试和试运行过程中遇到的故障进行了分析并制订了解决措施。     

An Experimental Investigation into the Feed Rate Capacity of Rotary Valve and Blow Tank Feeders

Industry widely uses rotary valves and blow tanks for the pneumatic conveying of products, each having their pros and cons depending on the specific application. This article shows the differing results obtained when low-velocity conveying a product through a common pipeline using both a drop-through rotary valve and a bottom-discharge blow tank feeder. A number of issues arise in the rotary valve system, the main one being rotary valve air leakage. A blow tank system, on the other hand, does not leak, as it is an enclosed system. The experimental results show dramatic differences in product throughput. Further exploration leads to a novel modification being made to the rotary valve system in an attempt to increase its capacity. The result of this modification shows a slight increase in output tonnage, but still significantly less than that obtained from the blow tank.     

纤维体积分数对K3D/MCPA复合材料力学性能的影响

本文研究了纤维体积分数对三维编织芳纶纤维增强铸性尼龙(简称K3D／MCPA)复合材料力学性能的影响。研究表明，K3D／MCPA复合材料有优异的抗冲击性能，冲击强度比三维编织芳纶纤维增强铸性尼龙(简称C3D／MCPA)和纯基体均有大幅度的提高，且随着纤维体积的提高而升高。K3D／MCPA复合材料剪切强度随纤维体积比的增大而增大，其纵向剪切强度低于纯基体和C3D／MCPA复合材料，但其横向剪切强度高于它们。K3D／MCPA复合材料弯曲强度与弯曲模量随纤维体积比的提高而提高，但与相同体积比的C3D／MCPA相比，K3D／MCPA的弯曲强度与弯曲模量均较低。     

转炉出钢口套整体袖砖工艺技术开发

介绍了天津天铁冶金集团有限公司炼钢厂转炉出钢口袖砖工艺的开发过程，主要工艺参数的制定，实践证明，该工艺的应用取得了良好的使用效果。     

Three‐dimensionally braided carbon fiber–epoxy composites,a new type of material for osteosynthesis devices. I. Mechanical properties and moisture absorption behavior

In recent years, three‐dimensionally (3D) braided composites have attracted a great deal of attention because of their high‐impact damage tolerance and fatigue life, superior fracture toughness, and so forth, and have been used in aeronautics, military, and transportation. These advantages make them strong candidates for osteosynthesis devices. In this study, 3D braided carbon fiber–epoxy (C_3D/EP) composites were produced via a simple vacuum impregnation technique. The load‐deflection curve, mechanical properties, and influence of fiber volume fraction, braiding angle, and axial reinforcing fibers were examined to determine their suitability for internal fixation devices. It is found that the C_3D/EP composites have excellent toughness and do not show brittleness when fractured because of their relatively high void content. The flexural, shear, and impact strengths of the C_3D/EP composites are excellent. It was shown that a C_3D/EP composite with a stiffness similar to load‐bearing bones can be made while maintaining enough strength. It is concluded that a relatively higher void content and braiding angle is more suitable for the C_3D/EP composites from the viewpoint of requirements of fracture fixation materials. The moisture absorption behavior and changes in mechanical properties caused by moisture uptake were evaluated. Results show that absorbed moisture slightly decreases mechanical properties of the C_3D/EP composites. Contrary to the unreinforced epoxy, the moisture absorption behavior of the C_3D/EP composites cannot be described with Fick's law of diffusion, probably because of the presence of voids and/or 3D fiber structure. The exact mechanisms should be proposed in further investigations. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 85: 1031–1039, 2002     

颗粒状物料气力输送系统中输料管的连接方式

对颗粒状物料的气力输送 ,人们往往只重视所要采用的输送方式 ,而忽视了输料管连接方式的正确选择、施工与安装。输料管连接方式的正确与否 ,直接影响到输送量和物料的品质。详细介绍了常用的几种连接方式 ,分析了它们的优缺点 ,并提出了比较合理的连接方式     

无键联接传动的特点及锥面弹性衬套设计和应用

无键联接在特殊行业和工况中是键联接传递动力和运动的有力补充,介绍了工程上应用的圆弧三边形型面联接、弹性环无键联接、圆柱面过盈联接等几种无键联接传动方式及其工作原理,并分析了各自的性能特点和应用情况。针对无键联接传动的特点、特殊行业和工况的应用实际,设计了锥面弹性衬套无键联接传动结构并介绍了其在工程中的实际应用。     

带肋钢筋套筒挤压连接的质量控制

针对太原可口可乐综合厂房主筋采用φ28、φ32三级钢存在的可焊性差的问题，提出了在施工中采用套筒挤压连接的方式，并对该方法的操作要点及质量控制措施进行了总结。     

三(明)钢烧结厂电除尘灰的气力输送

三钢烧结厂130m^2烧结机电除尘输灰首次采用了气力输送系统。该系统由气源、输送、管路、灰库及控制五部分组成，本文介绍了系统的工作原理及运行调试情况。系统投产后，运行平稳，达到了设计要求。