面向21世纪课程教材对地方综合大学电工学教学改革的影响--广西大学使用面向21世纪电工学课程系列教材的实践与探索

阐述了我校使用“面向21世纪”电工学课程系列教材的实践与探索过程，以及对我校电工学教学所产生的转折性影响和积极的导向作用，最后对教材提出了几点建议。     

以入世为契机,进一步推进电力科研院所企业化转制

我国入世和融入经济全球化，将给中国经济运行的大环境带来深刻变化，科技事业也面临着全新挑战。电力科研所实行企业化转制，与国际接轨，按照国际规则办事势在必行。作者作为电力科研单位的一把手就电力科研院所的企业化转制阐述了个人的观点。转制必须有利于回忆科技创新和高新技术产品的开发；必须有利于抓紧培养和造就复合型人才队伍；必须有利于更好地为电网、为发供电企业提供规范化、制度化、长期化和现代化的全方位服务。     

结构-波浪-海床耦合系统中大圆筒结构的波压力响应

以沉入式大圆筒结构为对象，通过设计随机波浪水槽实验，测取了在单筒和连续筒两种结构型式、两种沉入深度和两种波谱输入下结构表面的动波压力分布。波面高度以及波压力历程均在领域进行分析。通过计算结构表面沿高程和沿环向的波压力谱及波压力传递函数，将单筒实测结果与基于线性绕射理论的解析解进行了比较，同时也详细对比了两种结构型式下的实测结果。文中汇报了在研究中获得的新发现及进行的相应分析，特别是在结构——波浪——海床动力相互作用下对波压力响应机理以及针对连续筒的研究，可为工程应用提供有价值的参考。     

Powder Deposition in Three Parallel-Oriented Dies of Different Shapes

Uniformity of bulk density distribution during the die filling process is required to minimize quality problems, such as distortion and cracking, for powder compacts. Understanding the die filling process is necessary in ensuring a uniform powder deposition. The second-generation pressure deposition tester (PDT-II) was used to investigate the deposition process and final pressure distribution of powder filling in toroidal, cylindrical, and E-shaped dies. All tests were conducted using a spray-dried free-flowing granular powder. The results indicated that for toroidal dies: (1) the area around 0° orientation (the leeward end) had the highest pressure values (1186.7 to 2498.0 Pa), with the average pressure values of the remaining area 353.7-648.0 Pa; (2) the pressure distribution was symmetrical about the centerline parallel to the feed shoe movement direction; (3) the highest feed shoe speed (500 mm/s) led to the most nonuniform pressure distribution among the three speeds; (4) higher feed shoe speed did not always result in higher final pressure values; and (5) the right die tended to have higher final pressure values (215.0 to 2498.0 Pa) than the center die (95.4 to 2052.5 Pa). For E-shaped dies: (1) the final pressure values of the middle leg (308.9 to 760.7 Pa) were higher than those of the left and the right legs (148.9 to 530.3 Pa); (2) the area along the backside had the highest final pressure value (1054.6 to 1303.8 Pa); (3) the pressure distribution was symmetrical about the centerline parallel to the feed shoe movement direction; and (4) neither the center die nor the right die always had higher pressure values than the other one at all locations. Comparison between cylindrical and toroidal dies indicated that: (1) neither of the two die shapes (cylinder and toroid) led to consistently higher or lower final pressure values at all locations and (2) for all three feed shoe speeds, the toroidal die had higher average final pressure values in the 0° orientation.     

用双向扭转圆柱组合螺旋弹簧实现扭矩测试

利用单个圆柱螺旋扭转弹簧扭转原理,给出了一种用双向扭转圆柱组合螺旋弹簧实现扭矩测试的方法。根据扭转弹簧模型,给出了预紧力、加载的证明,并对实验结果进行分析;该结构用于扭矩测试系统既实用可靠,又简单易加工;降低了测试系统的成本,具有很高的实用价值。     

湘钢220KV备用电源自投方式商榷

针对湘钢三中央变电站２２０ｋＶ备用电源自投装置存在的问题，提出了新的方式和设想．分析采用新的方式后，停电时间由３．５ｓ缩短至０．０４～０．０９ｓ的可行性．同时还提出在ＳＦ６断路器的变电站，自投装置应采用的方式．     

差齿原理在推床同步调整技术中的应用

文章应用差齿原理在冶金设备初轧机推拉床实施转角性微调技术，以达到初轧机机前与机后推拉床同步调整效果．实践证明，效果显著，适用面广，且操作简单、方便经济．     

用圆柱铣刀加工带冠弯扭叶片

本文把微分几何中曲线与曲面之间的“切触”概念应用于叶片复杂曲面的数控加工，提出用圆柱铣刀的外圆在五坐标联动中加工小曲率曲面的最佳切触条件。     

筒形零件翻边模结构的改进

针对筒形件垂直翻边模,设计出了一种利用可滑动的凸模对其翻边.模具结构简单,性能可靠,加工方便,对此类模具设计有一定的借鉴作用.