川合137井大修井工艺技术浅析

在川合137井的修井作业中，运用了多种修井工具和工艺技术。通过内捞、外捞、强提、倒扣、磨铣、套铣、开钻新井眼和铣锥通井的方法，充分解放了油气层，达到了修井目的。其独特的想法、施工和自制工具的成功应用对今后大修井作业具有很高的参考价值。     

双转向垂向控缝技术实验研究及现场应用

针对压裂过程中缝高较难控制的问题，研制开发出新型的油溶性垂向双转向剂，并开展了室内实验研究。首次验证了转向剂对裂缝延伸的控制机理，确定了转向剂的适用浓度及控缝能力。实验表明，转向剂可以增加隔层应力3～4MPa左右。在此基础上研究了控制裂缝高度施工方案的设计方法，并利用全三维软件结合垂向应力剖面对控缝技术进行了优化。现场推广应用30井次，取得了较好的控缝效果。     

SHS of shape memory CuZnAl alloys

Aiming at preparation of shape memory alloys (SMAs), we explored the SHS of Cu_{1 − x} Zn_{1 − y} Al_{1 − z} alloys (0.29 < x < 0.30, 0.74 < y < 0.75, and 0.83 < z < 0.96). The most pronounced shape memory effect was exhibited by the alloys of the following compositions (wt %): (1) Cu(70.6)Zn(25.4)Al(4.0), (2) Cu(70.1)Zn(25.9)Al(4.0), and (3) Cu(69.9)Zn(26.1)Al(4.0). The effect of process parameters on the synthesis of CuZnAl alloys was studied by XRD, optical microscopy, and scanning electron microscopy (SEM). The grain size of CuZnAl was found to depend on the relative amount of the primary CuZn and AlZn phases. Changes in the transformation temperature and heat of transformation are discussed in terms of ignition intensity and compaction. Mechanism of the process depends on the level of the temperature attained relative to the melting point of components. At the melting point of AlZn, the process is controlled by the solid-state diffusion of AlZn into a product layer. The ignition temperature for this system depends on the temperature of the austenite-martensite transformation in CuZnAl alloys. The composition and structure of the products was found to markedly depend on process parameters. The SHS technique has been successfully used to prepare a variety of SMAs.      

Microstructural and compositional aspects of ZnO-based varistor ceramics prepared by direct mixing of the constituent phases and high-energy milling

ZnO-based varistor samples were prepared by the direct mixing of the constituent phases (DMCP) and sintering at 1100 °C for 2 h. The influence of the starting powder mixture's composition – the amounts of the pre-reacted varistor compounds and their composition – and its preparation, either with or without mechano-chemical activation (MCA), on the microstructure, phase composition and electrical characteristics of the varistor samples was studied. It showed that MCA improved the density and microstructural homogeneity of the varistor samples. MCA strongly affected the grain growth: it enhanced the nucleation of inversion boundaries (IBs) in the ZnO grains and the IBs-induced grain-growth mechanism resulted in uniform grain growth and hence a microstructure with smaller ZnO grains and a narrower grain size distribution. The final phase composition of the samples prepared by the DMCP method mainly depended on the presence of varistor dopants that can prevent the formation of the pyrochlore phase, especially Cr₂O₃, while MCA can affect it mostly by providing a homogeneous distribution of those dopants. The DMCP varistor samples prepared with MCA had much better current–voltage characteristics than the samples of the same composition prepared from unactivated powders.     

原料扩重的中压加氢改质装置投产

介绍燕山石化公司为扩大1Mt／a中压加氢改质装置的原料来源，改用大庆减二线油和重油催化裂化柴油组成的混合料开工投产的经验以及装置初期的运行条件。中压加氢改质技术可以生产优质柴油和蒸汽裂解制乙烯的原料，还可增产喷气燃料。     

机械合金化Fe50Ti50非晶的形成及球磨强度对它的影响

本文通过电子扫描和Ｘ衍射对机械合金人Ｆｅ５０Ｔｉ５０非晶粉末形成做了研究。研究发现：机械合金非晶形成可以大致地分为二个阶段－粉末的破碎阶段和非晶的形成阶段。另外，对球磨强度对非晶形成的影响进行了研究。结果表明：强度低时粉末需要较长的时间才能形成非晶，强度高时粉末形成非晶的时间大大缩短，但在随后的球磨中，粉末会重新晶化形成新相。     

市县HFC系统如何选择和使用光端机

对有线电视工程设计中如何选用优质设备、提高网络质量等问题进行探讨     

被动锁模复合环形腔掺饵光纤激光器的自启动分析

本文对被动锁模复合环形腔掺饵光纤激光器的自启动工作特性进行了分析，指出谐振腔内残余反射面的存在是阻碍激光器实现自启动锁模的主要原因。利用半导体激光器有源区的折射率随注入电流的变化而改变的特性，在谐振腔中获得了一个可移动腔镜，克服了腔内残余反射面的影响，实现了锁模的自启动。     

变速铣削的试验研究

通过试验考证了变速铣削的减振效果和机床电机电流的波动幅度，试验结果表明，变速铣削同样具有明显的减振效果。机床电机电流虽有波动，但波动幅度不大，不会影响电机的正常使用，变速铣削具有良好的应用前景。     

Hysys软件在分析精丙烯硫化物来源中的应用

气体分馏装置原料液化石油气 (LPG)中有机硫化物形态复杂 ,考察分析工业装置精丙烯硫化物含量变化难度大。利用Hysys模拟 ,分析判断LPG中小分子有机硫化物在气体分馏产品的分布并提出了控制措施。考虑操作条件对精丙烯硫含量的影响 ,并对工业装置精丙烯总硫超标原因进行了分析。