交流伺服系统在玻璃裂片机中的应用

随着运动控制技术的飞速发展，交流伺服系统应用的日益广泛。介绍了液晶生产中的关键设备玻璃裂片机，并详细分析松下MINAS A系列交流伺服系统在玻璃裂片机中的应用。     

构建高扩展性的县级广电宽带数据网络

提出在县市级广电宽带数据网络的建设过程中,要着眼业务发展,突出高扩展性,构建基于标准、扩展灵活的主干网,实现网络建设的可持续性发展,并结合实际,从核心设备、端口、中继带宽、网络业务4个方面对扩展能力进行了阐述.     

β21s高强度钛合金的铣削试验研究

针对一种新型的难加工钛合金材料β21s,进行了刀具磨损试验和铣削力的测量试验,对材料的切削加工性进行评价,并且给出优选结果,为实际生产提供参考。     

Formation of layered structure on bismuth-borate glass surface

X-ray diffraction analysis shows that the transformation during heat treatment from amorphous to crystalline phases of bismuth-borate glass samples takes place in sequences. After a short heat treatment, 5 min at 550 °C, a layered structure with a preferred orientation of crystallites on the surface is observed. After a long heat treatment, 8 h at the same temperature, normal polycrystalline bulk samples are obtained.     

Effect of Bonder at Skin/Core Interface on the Mechanical Performances of Sandwich Structures Used in Marine Industry

The present work is aimed to extend the knowledge of mechanical properties of sandwich structures used for marine applications focusing on the possibility to increase the performances of such structures by adding a bonder at the skin/core interface. Therefore, three sandwich structures that are utilised in different structural components of a yacht were realised by manual lay-up. The mechanical characterisation was performed by flatwise compressive, edgewise compressive and three point flexural tests. The tests execution has allowed both to determine the mechanical performances and to understand the fracture mechanisms that take place when the bonder is added in the stacking sequence of the samples.     

Prediction of necking of high strength steel tubes during hydroforming—multi-axial loading

This article studies tubular hydroforming of high strength low alloy (HSLA) and dual phase (DP600) straight tubes under the action of end feeding loads. Experiments demonstrate that higher end feed loads enhance the formability of the tubes and increase the internal fluid pressure for onset of necking and bursting. Because of the action of the internal pressure and the axial compressive load, the onset of localization (necking) is due to a complex three-dimensional state of stress. Using free expansion experiments, approximate upper and lower bound strain-based forming limit curves are determined for the tube materials. These limit curves, in turn, are used to derive upper and lower bound extended stress-based forming limit curves [Simha et al., Prediction of necking in tubular hydroforming using an extended stress-based FLC. Transactions of the ASME Journal of Engineering Materials and Technology 2007;129(1): 36-47]. In conjunction with finite element computations that use solid elements to model the tube, these stress-based limit curves are used to predict upper and lower bound necking pressures under the action of end feed loading. These predictions of necking pressures, when an appropriate coefficient of tube-die friction is used, are found to bracket the experimentally measured necking pressures. Computations using plane stress shell elements to model the tubes are shown to give erroneous results, since the plane stress approximation is not valid when tubes are hydroformed in a die.     

熔窑玻璃液流数值模拟的新发展

熔窑玻璃液流数值模拟的新发展赵国昌（清华大学核能技术设计研究院，１０００８４）ＮｅｗＤｅｖｅｌｏｐｍｅｎｔｏｆｔｈｅＮｕｍｅｒｉｃａｌＳｉｍｕｌａｔｉｏｎｆｏｒＦｌｏｗａｎｄＨｅａｔＴｒａｎｓｆｅｒｏｆＧｌａｓｓＭｅｌｔｉｎＴａｎｋＦｕｒｎａｃｅ￥Ｚ...     

Behaviour of ±45° glass/epoxy filament wound composite tubes under quasi-static equal biaxial tension–compression loading: experimental results

The primary aim of this paper is to present results describing in detail the behaviour of ±45° E-glass/MY750 (GRP) tubes, of various wall thicknesses, subjected to equal biaxial tension–compression loading, generated under combined internal pressure and axial compression. The role played by the non-linear lamina shear has also been assessed by comparing various shear stress–strain curves for embedded laminae (extracted from tests on ±45° tubes subjected to circumferential: axial stress ratios SR=1:0, 1:−1 and 2.3:−1) with that of an ‘isolated’ lamina (measured from torsion of 90° tubes). Extracted shear failure strains, for embedded laminae, were more than four fold larger than those measured at ultimate failure for an ‘isolated’ lamina. Soft characteristics were observed in the embedded lamina and these were believed to be due to interaction between early matrix damage initiation (and propagation) and shear. Factors affecting the behaviour of the tubes, such as bulging, scissoring, thermal stresses and stress variation through the thickness are discussed.     

蓄热室效能剖析

提高蓄热室效能是降低池窑能耗的有力措施.本文分析了反映蓄热室热交换能力的综合传热系数,进一步探讨了格子砖内部热交换过程和外部热交换过程中的矛盾以及解决矛盾的方法,继而谈及妥善处理在增加格子砖热交换表面上的矛盾,最后提出了衡量蓄热室效能的技术-经济指标以及提高技术指标的主要途径.     

氟挥发对氟化物乳白玻璃瓶罐生产的影响

氟挥发对氟化物乳白玻璃瓶罐生产的影响陆德明，周俊梅，付希英（山东轻工业学院２５０１００）（山东德州玻璃厂２５３０１９）ＴｈｅＩｎｆｌｕｅｎｃｅｏｆＦｌｕｏｒｉｎｅＶｏｌａｔｉｌｉｚａｔｉｏｎｏｎＰｒｏｄｕｃｔｉｏｎｏｆＦｌｕｏｒｉｄｅｏｐａｌＧｌａｓ...