不同晶相结构ZrO2负载铜基催化剂用于二乙醇胺脱氢反应

通过制备不同晶相结构〔单斜相(m-ZrO_2)、四方相(t-ZrO_2)和无定型(a-ZrO_2)〕ZrO_2载体,再通过沉积沉淀法制得Cu/m-ZrO_2、Cu/t-ZrO_2和Cu/a-ZrO_2催化剂,分别用于催化二乙醇胺脱氢合成亚氨基二乙酸反应。采用XRD、氮气物理吸附脱附、XPS、H_2-TPR、CO_2-TPD对催化剂的结构进行了表征。结果表明,Cu/m-ZrO_2催化剂界面更加有利于Cu~+/Cu~0稳定存在,具有更多的碱性位点,且抗氧化性较好。在二乙醇胺脱氢反应中,Cu/m-ZrO_2催化剂性能最好,反应时间为2.5 h,亚氨基二乙酸收率为97.64%。     

2.4GHz动态CMOS分频器的设计

对现阶段的主流高速CMOS分频器进行分析和比较,在此基础上设计一种采用TSPC(truesingle phase clock)和E-TSPC(extended TSPC)技术的前置双模分频器电路.该分频器大大提高了工作频率,采用0.6μm CMOS工艺参数进行仿真的结果表明,在5V电源电压下,最高频率达到3GHz,功耗仅为8mW.     

Defocusing image to pattern contact holes using attenuated phase shift masks

The patterning of contact holes by selecting out-of-focus image plane (defocus) using attenuated phase shift masks (APSM) has been studied. Defocus is found to enhance the image modulation at low partial coherence for contact holes with negative local average of mask function. Semi-dense holes up to 130 nm in 8% APSM have been printed by 0.5 μm defocus at a partial coherence of 0.31 using KrF scanner with highest numerical aperture of 0.68. However, these holes were closed with in-focus imaging. Defocus is also found to be beneficial for patterning the pitches that have extensive side lobes with in-focus imaging.     

摩擦换向抽油机悬点运动分析计算

摩擦换向抽油机采用开关磁阻电动机或变频调速电动机,其特点是可以频繁双向旋转,带动摩擦轮正反转,实现光杆的上行下行。该抽油机运动特点与游梁式抽油机运动特点有较大区别,文章分析了摩擦换向抽油机的运动特点,给出了该机悬点位移、速度、加速度的计算方法。     

Monte Carlo simulation of gas phase polymerization of 1,3‐butadiene. Part II: Kinetics optimization and confirmation

Studies on the deactivations and initiations of gas phase polymerizations of 1,3‐butadiene have been achieved by Monte Carlo simulation. Initiation and deactivation control the reaction before and after the peak of the polymerization rate, respectively. The influence of polymerization temperature has been studied. Monte Carlo modeling of polymerization kinetics and mechanism was confirmed by the agreement of experimental data and simulation results of polymerizations run with a temporary evacuation of monomer. The balance of catalysts and active chains is established by both initiation and chain transfer reactions with cocatalyst, which causes a ‘pseudo‐stability’ stage. © 2003 Society of Chemical Industry     

连续波雷达测距中的解模糊技术

研究连续波雷达测距中的距离模糊问题，分析几种常用解模糊方法的性能，并讨论参差比的选取对测距范围的影响。     

热管传热性能对小型热管换热器散热效能影响

在零重力辅助下,小热管热阻是小型热管换热器散热效能的重要影响因素之一。基于集总参数法对于换热器系统数值计算的高效性思想,建立了热管、热管换热器的集总参数模型。对同一热管换热器选用不同传热性能的热管,在不同传热温差和流体质量流速下,就其散热效能进行了数值计算。计算结果表明,在零重力辅助下,热管换热器管内热阻存在一临界值Rcri。当热阻RHP≤Rcri时,管外热阻起主导作用,热管换热器的散热效能εh几乎不随热管管内热阻的值而变化。     

机械合金化Fe-Ni粉末的相结构

使用XRD和Moessbauer等方法，研究了在Ar气氛下机械合金化Fe—Ni粉末相结构的变化．结果表明，在机械合金化Fe64-Ni36粉末过程中，fcc相的数量随着球磨时间的增加先增加然后减少，与加乙醇球磨Fe64-Ni36的情形相同．当Ni的含量(原子分数)大于50％时，有fcc相、顺磁相和FeNi3形成，当Ni的含量低于50％时，bcc相的数量随着Ni含量减少而增加．Moessbauer谱的结果表明，因球磨时间或Fe、Ni比例的不同，Fe—Ni球磨粉末固溶体具有不同结构的原子配比。     

Volumetric Change and Surface Properties of Temperature-Sensitive Polyvinylalcohol (PVA) Hydrogel

Polyvinylalcohol (PVA) polymer gel is a temperature sensitive polymeric gel, with a critical transition temperature (with H₂O) of 310 K. At higher than 310 K, this temperature sensitive polymer gel shrinks because of discharging water, whereas at lower temperatures, the gel swelled because of absorbing water. The reversibility of the gel's volume change was confirmed by temperature swing. The adsorption behavior of an organic compound onto the PVA polymer gel in water was tested at various temperatures. The amount of adsorbed organic compound increased remarkably at temperatures higher than about 310 K. Then, it was confirmed that the organic compound in PVA polymer gel could be reversibly adsorbed and desorbed by a temperature change between 293 and 323 K. The mechanism of adsorption of the organic compound onto the PVA polymer gel could be explained by hydration and dehydration of polymer gel.     

带通采样在数据采集中的应用研究

在数据采集中采用带通采样，可大大降低采样率，但系统中的抗混叠滤波器会造成相位的非线性。采用对滤波后的信号进行带通采样，然后再用FRR滤波器校正相位的非线性，从而不失真地还原原信号，最后在Matlab中进行仿真，验证了该方法的有效性。