Electrochemical synthesis and characterization of chloride doped polyaniline

Chloride doped polyaniline conducting polymer films have been prepared in a protic acid medium (HCl) by potentiodynamic method in an electrochemical cell and studied by cyclic voltammetry and FTIR techniques. The FTIR spectra confirmed Cl^- ion doping in the polymers. The polymerization rate was found to increase with increasing concentration of aniline monomer. But the films obtained at high monomer concentration were rough having a nonuniform flaky polyaniline distribution. Results showed that the polymerization rate did not increase beyond a critical HCl concentration. Cyclic voltammetry suggested that, the oxidation-reduction current increased with an increase in scan rate and that the undoped polyaniline films were not hygroscopic whereas chloride doped polyaniline films were found to be highly hygroscopic.     

Synthesis of LiFePO4 with fine particle by co-precipitation method

LiFePO₄ is a potential candidate for the cathode material of the lithium secondary batteries. A co-precipitation method was adopted to prepare LiFePO₄ because it is simple and cheap. Nitrogen gas was needed to prevent oxidation of Fe²⁺ in the aqueous solution. The co-precipitated precursor shows the high reactivity with the reductive gas, and the single phase of LiFePO₄ is successfully synthesized with the aid of carbon under less reductive conditions. LiFePO₄ fine powder prepared by co-precipitation method shows high rate capability, impressive specific capacity and cycle property.     

Corrosion Behavior of 316LN and 316 Stainless Steels During Long-term Exposure to Aerated 0.5 M NaCl Using Electrochemical Noise Technique

In the present work 316LN as well as 316 stainless steel (SS) coupons each of dimensions (0.025 × 0.018 × 0.006 m³) in well-polished condition were used as two nominal electrodes which were immersed in the aerated solution of 0.5 M NaCl. Correlated current and potential electrochemical noise (EN) signals were collected at 1 Hz sampling frequency for 1 h daily over a period of 30 days. The detrended EN data were used to calculate the noise resistance (R _N) as well as the spectral noise resistance at zero frequency (R _SN^o) values and other statistical parameters. To study the nature of pits and distribution of their diameters as well as depths, extensive observations of the pitted and the blank specimens were carried out using Confocal Laser Scanning Microscopy (CLSM). The current and the potential records of the two alloys showed distinct differences in their corrosion behavior. It was observed that within less than 4 h of immersion, 316SS showed signals indicative of unstable pitting and onset of stable pitting was noticed after 48 h of exposure. However, until about 24 h, 316LN showed just the random signals and unstable pitting was observed after 28 h. The signals clearly indicated continuous growth of the stable pits in 316SS as against the repassivation of the unstable pits in 316LN after 7 days exposure. It was observed that R _N values showed a continuous decrease in the case of 316SS, but were quite stable in the case of 316LN over the exposure period. Concurrent to these observations it was observed that 316SS specimen was extensively pitted. The frequency distributions of pit diameters as well pit depths were observed to be highest at 10-20 μm and 5-10 μm, respectively. However, pits with as large as 70-80 μm diameter and as deep as 20-25 μm too were observed. No pits were observed in case of 316LN even after 30 days of exposure, an observation that corroborates well with the stable R _N values. Thus, in the present investigation, the long-term tests using EN technique coupled with CLSM studies conclusively prove that many unstable pits initiated in 316SS turn into stable ones resulting in insidious localized corrosion attack whereas the unstable pits initiated in 316LN get passivated in the simulated coastal environment.     

镍氢电池负极用低成本储氢合金的研究

研究了ABS型储氢合金在低Co含量条件下，随B组元替代元素Co，Al，Si等含量的变化对合金电化学性能的影响规律，同时研究了A组元中不同La／Ce比对合金电化学性能的影响情况。结果表明，随合金中Co含量的降低，合金的活化性能和放电容量得以改善，但合金的循环寿命下降也比较明显；在试验范围内，随Al元素的加入，合金的循环寿命得以改善，但材料的放电容量和活化性能均有所下降；随合金La／Ce比的降低，合金的放电容量略有下降，但其循环寿命和放电电压平台有较大提高。     

High‐Performance,Monolithic Polyaniline Electrochemical Actuators

New polyaniline (PANI) asymmetric membranes were fabricated using a phase‐inversion technique with hexane as the coagulation bath. These membranes exhibit a dense structure with macrovoids distributed asymmetrically throughout the cross‐section. A stress–strain study demonstrated that the Young's modulus (1.421 GPa) and strain at break (7.6 %) of the new PANI asymmetric membranes prepared from hexane are approximately 12 and 4 times higher, respectively, than the values reported previously for the PANI integrally skinned asymmetric membranes (ISAMs) (123 MPa Young's modulus and 1.8 % strain at break). Furthermore, monolithic electrochemical actuators based on a single PANI asymmetric membrane were constructed, and a bending movement of up to 20 Hz was experimentally recorded in a hydrochloric acid aqueous solution. A lifetime of over 329 500 cycles was determined for these actuators at a ± 2° angular displacement (5 Hz). The lifetime is limited by a bending fatigue that creates a transversal crack on the PANI membrane at the air–water interface. Control over the actuator movement is also manifested by the linear dependences of the bending angle on the charge and of the angular velocity on the current. These relationships are independent of both the kind of applied electric signal and the frequency used.     

Reactor modelling for electrochemical processes

This paper presents a relatively straightforward approach to the modelling of electrochemical reactors operated in batch or continuous modes. The models are based on ideal flow assumptions of either well-mixed or plug flow and incorporate reaction rate models based on electrochemical kinetics and mass transport at one electrode. General characteristics of the reactor models are described, particularly with regard to the need for good mass transport in metal recovery applications. An example is given on the use of the model in the recovery of a heavy metal (Cd²⁺) from an acidified solution containing Cd(II) and Fe(III) ions. The reaction rate model is based on experimental data.     

Electrosynthesis and impedance studies on zinc selenide

Electrochemical impedance measurements have been used to characterize zinc selenide films prepared by electrochemical co-deposition at a platinum rotating disk electrode. Estimations of capacitance and polarization resistance of variously prepared electrodeposits have been carried out to determine charge carrier density and corrosion rates.     

Dental amalgam – the effect of the technology of alloy powder preparation on the corrosion behaviour and the release of mercury

Dental amalgams are based on a broad spectrum of materials differing in their chemical composition, metallurgical treatment, and in the way the initial alloys powders are prepared. In addition to their chemical composition, amalgams based on various powders differ in both their microstructure and the amount of mercury needed for preparation. All these facts may affect electrochemical processes occurring during their interaction with oral fluids, and also mercury release. While verifying the effect of the technology used for the preparation of the high‐copper ternary alloy powder on the properties of resulting amalgams, this study aimed at the mechanism of their interaction with a model saliva solution as well as mercury release was included. Measurements were done in a model saliva solution using standard electrochemical methods and exposition measurements. The interaction of individual types of amalgams with artificial saliva did not reveal any significant differences. The free corrosion potential of all these amalgams in an aerated solution settled in the range of values in which tin oxidation, resulting in a layer of insoluble corrosion producsts, turned out to be the dominant anodic process. The rate of mercury release was the lowest for amalgams based on a gas‐atomized alloy. The highest rate of mercury release, and also its dependence on time, was exhibited by lathe‐cut powder based amalgam. In addition to different volume fraction of the Ag‐Hg phase and the level of its tin alloying, this different behaviour may be explained by differences in the rate at which a layer of tin corrosion products acting as a barrier to mercury release is formed.     

A disposable single-use electrochemical sensor for the detection of uric acid in human whole blood

We report here a non-enzymatic detecting electrode strip for fast monitoring of uric acid in human whole blood. A single-use amperometric uric acid sensor strip, incorporating a three-electrode configuration, has been fabricated on a polypropylene substrate using low cost screen-printing (thick-film) technology. Both the working and counter electrodes were prepared by screen-printing commercial carbon ink. The integration on the same support of pseudo-reference electrode was obtained by screen-printing a commercial silver ink and subsequent electrochemical pretreatment. Simply by placing a 20 μl human whole blood drop on the strip is enough for uric acid analysis by square-wave voltammetry. Real human whole blood samples were analyzed by this method and compared to the phosphotungstic acid clinical test procedure with satisfactory results.     

溶液温度对电化学沉积氧化亚铜薄膜相成分和显微结构的影响

用电化学方法在不锈钢基体上沉积多晶Ｃｕ２Ｏ薄膜并用Ｘ射线衍射和扫描电进行了分析研究了溶液温度对薄膜相组成、晶粒尺寸和择优取向的影响，当溶液的ＰＨ＝９，温度低于５０℃时得到的是Ｃｕ２Ｏ／Ｃｕ复相薄膜，纯Ｃｕ２Ｏ薄膜可在溶液温度高于５０℃时获得，纯Ｃｕ２Ｏ薄膜具有（１００）择优取向，实验发现薄膜的晶粒尺寸随溶液温度的增加从０．１２μｍ增加到０．６５μｍ。