Structural changes in isothermal crystallization process of polyoxymethylene investigated by time-resolved FTIR, SAXS and WAXS measurements

Structural evolution in the isothermal crystallization process of polyoxymethylene from the molten state has been investigated by carrying out the time-resolved measurements of infrared spectra and synchrotron small angle X-ray scattering (SAXS) and wide angle X-ray scattering. In case of isothermal crystallization at 130 °C, for example, the infrared bands intrinsic of folded chain crystal (FCC) morphology appeared at first, and then the bands of extended chain crystal (ECC) morphology were detected with time delay of ca. 150 s. In the SAXS experiment at 130 °C, the lamellar stacking structure of the long period of ca. 15 nm was observed at first, which changed rapidly to ca. 12 nm in a short time. The SAXS peak with the long period of ca. 6 nm started to appear with a time delay of ca. 150 s after the initial lamellae appeared and coexisted with the initially-observed 12 nm peak. Judging from the timing to detect these characteristic infrared and SAXS signals, a good correspondence was found to exist between the stacked lamellar structure of 12 nm long period and FCC morphology and between the structure of 6 nm long period and ECC morphology. The quantitative analysis was made for the SAXS data on the basis of the lamellar insertion model combined with the paracrystalline theory of the second-kind of disorder. The following structural evolution was deduced from all these results. Immediately after the temperature jump from the melt to 130 °C, the stacked lamellar structure of FCC morphology was generated at first. New lamellae were formed from the amorphous region in between the originally-existing lamellae about 150 s later, where the random chain segments bridging the adjacent lamellae were extended to form the taut tie chains, giving infrared bands of ECC morphology. This inserted lamellar structure of 6 nm long period coexisted at a population of ca. 6% with the initially-formed lamellar stacking structure of 12 nm long period. When the experiment was made at 150 °C, only the formation of stacked lamellar structure of FCC morphology was observed and the insertion of new lamella did not occur.     

化学复合镀层激光处理研究

研究了激光处理对Ni-P -SiC化学复合镀层的影响。借助于扫描电镜、能谱仪、X射线衍射、显微硬度计等设备对激光处理后复合镀层的表面形貌、组织结构及性能进行了综合分析。结果表明 ,对复合镀层进行激光处理可以获得与炉内加热同样的镀层硬度 ,且当激光功率 4 0 0W ,扫描速度 1.5m /min时 ,镀层硬度高于炉内加热的硬度     

掺气减蚀保护作用的新概念

利用针式掺气流速仪测量原型和模型掺气浓度场、流速场，气泡尺寸及其概率分布的研究成果表明，原型水流韦伯数高，形成微小气泡的能力比模型强，气泡上浮慢，接近底部的小尺寸气泡概率及掺气浓度比模型大。初步研究认为：0.2mm或0.5mm以下的微小气泡在掺气减蚀中起着主要作用，可能只要很小掺气浓度即可达到掺气减蚀的效果。因此以小尺寸气泡的掺气浓度，作为判断掺气减蚀保护作用的指标将更为准确。     

石膏转化制硫酸钾结晶动力学及结晶添加剂研究

研究了浓氨介质中石膏与氯化钾直接转化制硫酸钾的结晶动力学及结晶添加剂的作用效果。结果表明 ,硫酸钾在氨介质中的成核速率与晶体生长速率、悬浮密度、搅拌速率存在如下关联式 :B0 =5 .64 13×10 8G3.32 0 8Mt0 .0 559np0 .2 92 8。加入异丙醇、OP乳化剂及十二烷基苯磺酸钠等添加剂 ,可使硫酸钾结晶产品纯度提高 ,晶体形态整齐均匀     

双塔脱丙烷工艺技术

对扬子乙烯装置双塔脱丙烷系统低压塔液泛、高压塔再沸器堵塞等问题进行了技术分析,提出了工艺流程修改方案,完善了双塔脱丙烷技术,对同类装置有参考价值。     

Clarification of a wheat straw‐derived medium with ion‐exchange resins for xylitol crystallization

BACKGROUND: Xylitol bioproduction from lignocellulosic residues comprises hydrolysis of the hemicellulose, detoxification of the hydrolysate, bioconversion of the xylose, and recovery of xylitol from the fermented hydrolysate. There are relatively few reports on xylitol recovery from fermented media. In the present study, ion‐exchange resins were used to clarify a fermented wheat straw hemicellulosic hydrolysate, which was then vacuum‐concentrated and submitted to cooling in the presence of ethanol for xylitol crystallization. RESULTS: Sequential adsorption into two anion‐exchange resins (A‐860S and A‐500PS) promoted considerable reductions in the content of soluble by‐products (up to 97.5%) and in medium coloration (99.5%). Vacuum concentration led to a dark‐colored viscous solution that inhibited xylitol crystallization. This inhibition could be overcome by mixing the concentrated medium with a commercial xylitol solution. Such a strategy led to xylitol crystals with up to 95.9% purity. The crystallization yield (43.5%) was close to that observed when using commercial xylitol solution (51.4%). CONCLUSION: The experimental data demonstrate the feasibility of using ion‐exchange resins followed by cooling in the presence of ethanol as a strategy to promote the fast recovery and purification of xylitol from hemicellulose‐derived fermentation media. Copyright © 2008 Society of Chemical Industry     

Poly(butylene terephthalate)–clay nanocomposites prepared by melt intercalation: morphology and thermomechanical properties

Nanocomposites based on poly(butylene terephthalate) (PBT) and an organoclay (Cloisite 30B) were prepared by melt blending using a twin‐screw extruder. Two kinds of PBTs, ie PBT‐A and PBT‐B, with different inherent viscosities (η_inh), were used for this study (η_inh of PBT‐A and PBT‐B were 0.74 and 1.48, respectively). Dispersion of the clay layers in the PBT nanocomposites was characterized by using X‐ray diffraction (XRD) and transmission electron microscopy (TEM). Tensile and dynamic mechanical properties and non‐isothermal crystallization temperatures of the nanocomposites were also examined. Nanocomposites based on the higher‐viscosity PBT (PBT‐B) showed a higher degree of exfoliation of the clay and a higher reinforcing effect when compared to the composites based on the lower‐viscosity PBT (PBT‐A). The clay nanolayers dispersed in PBT matrices lead to increases in the non‐isothermal crystallization temperatures of the PBTs, with such increases being more significant for the PBT‐B nanocomposites than for the PBT‐A nanoocomposites. Copyright © 2004 Society of Chemical Industry     

真空制盐蒸发结晶器的设计与实践

真空蒸发制盐外热式强制逆循环轴向出料蒸发结晶器，经多个厂家生产应用实践证明是成功的，具有生命力的。这种新型结构，作为一项新技术新设备应加强研究，总结提高，推广应用。不断完善。文章从流体力学、结晶机理角度要求，到具体工程设计参数和材质选用。论述了该罐的特点。