现场总线技术在城市污水处理与气象中的应用

文章主要讨论了LonWorks现场总线技术在城市污水处理厂和气象指数预报中的应用。采用IPC和PLC控制结构对现场的各种设备实现控制和数据的采集，通过现场总线网络传输数据到中心控制室或远程终端，实现污水处理的自动控制和气象信息的实时采集和处理。     

Improved Matrix-Filler Adhesion

Enhanced matrix-filler adhesion is realized after filler treatment with a surface treatment process. The hydrosol/coupling agent treatment was applied to a wide range of inorganic and organic fillers, and adhesion to a variety of matrix resins was improved. Scanning Electron Microscopy (SEM) was used to determine the locus of failure in the filled systems. The locus of failure shows the relative degree of adhesion between the filler and the polymer matrix. Significant improvement in adhesion in humid environments is also observed.     

Off-Site Exposure to Respirable Aerosols Produced during the Disk-Incorporation of Class B Biosolids

Field experiments were conducted at a Class B biosolids land application site in central Arizona to measure, model, and source-track the off-site transport of aerosols emitted when biosolids were disk-incorporated into soils. Real-time PM10 monitoring provided time-resolved aerosol information sufficient for verifying both off-site concentration and off-site exposure time model results. Under the conditions considered and at a distance of 165?m from the aerosol source, biosolids disk-incorporation resulted in an intermittent exposure to biosolids-derived aerosol concentration between 15 and 40?μg/m3 and an inhalable biosolids dose between 2 and 8?μg. Transport modeling predicted that these doses will decrease with increasing wind speed. In addition, three DNA sequence-based biosolids source tracking methods were applied to aerosol samples and confirmed the presence of biosolids in aerosols at 5, 65, and 165?m from the aerosol source. Field measurements and modeling indicate that the nature of biosolids-derived aerosol exposure is a series of intermittent high concentration puffs, rather than a continuous low concentration.     

The Application of Ozone for Water Treatment In The United Kingdom — Current Practive and Recent Research

Only two water works in the UK apply ozone at present as part of their treatment, onefor taste and odor control and theother forcolor removal. Forthetwo applicationus ozone was the most economical option at thetime theplants were installed andozone has been successful for the purpose for which it was designed.     

城市污水处理厂的施工监理

指出施工监理是一项细致而又责任重大的工作。把握好污水处理厂关键工序的施工及检查,才能对污水处理工程进行有效地控制和管理,使之发挥最大的经济和社会效益。     

浅谈赣抚大堤樟防1标射水造墙的接缝技术和处理措施

介绍射水造墙的接缝原理，并把自己在施工过程中为确保接缝质量达到设计要求而总结出一些经验和处理措施提出为一起探讨。     

Treatment of Humic Waters By Ozone

Two different generators for ozone were tested, a traditional electrical discharge generator and a generator based upon UV–irradiation of air at 150–180 nm. It was demonstrated that the traditional generator gave slightly higher reductions in levels of color for equivalent ozone dosages. Both gases affected the molecular weight distribution in the way that the bigger molecules were broken down to smaller ones. No significant difference between the molecular weight reduction efficiency of the gases was found.     

Uses of Ozone in a Three-Phase System for Water Treatment: Ozone Adsorption

A new technique of using ozone for water treatment is presented. This new technique consists of using a three-step-process composed firstly of ozone adsorption on an appropriate adsorbent, secondly water treatment, and thirdly regeneration of the adsorbent. Results regarding ozone adsorption (the first step) are presented in this paper. Different types of silica gel and a type of TiO₂ have been tested for ozone adsorption. It was found that the physical characteristics of the silica gel affect its capacity for ozone. Titanium dioxide has shown ozone decomposition instead of adsorption as it contains Lewis acid sites. An exponential decrease of the silica gel capacity with its moisture content has been found. Linear isotherms in the range of ozone concentrations less than 100?g/m³ NTP have been found. A particle diffusion model with linear equilibrium isotherm has been used to model the breakthrough curves in fixed bed columns.     

Thermal Generation of Residual Stress Fields for Purpose of Distortion Minimization

Thermal treatments of steel components with the goal of hardening often result in distortion by releasing the residual stresses which were brought into the specimen during the preceding processing steps. The goal of the presented work is the minimization of this distortion. By generating definite residual stress fields and investigating the resulting distortion, the distortion mechanism can be observed in detail. A flexible and reproducible way to generate such residual stress fields inside a specimen is by means of local thermal treatment with a laser beam. Computer simulations as well as experiments were carried out using an idealized tooth of a gearwheel (finger sample) as a model system. The deformation of the samples due to the laser heat treatment and the stress fields generated inside the samples were determined with respect to different process parameters.     

Influence of the silicon surface treatment by plasma etching and scratching on the nucleation of diamond grown in HFCVD - a comparative study

A comparative study for the nucleation of diamond was carried out using surface treatment like (i) surface scratching with 1 μm diamond paste and (ii) surface etching using chlorine plasma at different RF powers (50, 100 and 150 W). Atomic force microscopic study shows variation in roughness from 31 nm to 110 nm. Scratching results in random scratches, whereas plasma etches a surface uniformly. Scanning electron microscopic observations show well faceted crystallites with a predominance of angular shaped grains corresponding to 〈100〉 and 〈110〉 crystallite surfaces for the scratched as well as plasma etched substrate. Surface etching at 150 W plasma power results in a better growth in comparison with 50 and 100 W plasma powers. Chlorine-radical is found responsible for the changes in the growth morphology. Raman spectroscopy shows a sharp peak at 1,332 cm⁻¹ and a peak at ∼1,580 cm⁻¹ for both samples.