A quantum chemical study on structure of 1,2-bis(diphenylphosphinoyl)ethane and phenol cocrystal

The cocrystal of 1,2-bis(diphenylphosphinoyl)ethane (DPPEO) with phenol (1:1) were studied theoretically with AM1, PM3, MNDO and MINDO/3 semi-empirical methods to elucidate its structure. The bond lengths and angles from theoretical studies of molecule DPPEO/phenol (1:1) were found to be as expected. Theoretical results, concerning with intermolecular van der Waals forces in cocrystal, were compared with the previously obtained experimental data and AM1 results were found to be the best fit for bond lengths and angles of DPPEO/phenol.     

Dependence of the kinetics of the anionic polymerization of methyl methacrylate on the concentration in active centers

Studies on the anionic polymerization of methyl methacrylate in tetrahydrofuran and in the presence of sparteine have revealed a beneficial effect due to this additive, resulting in a decrease in the extent of termination. Better control of the definition of the polymers formed can thus be achieved in the presence of this additive. On the other hand, macromolecular engineering requires a range of active species concentrations lower than 10^?3 mol L^?1 and particularly the synthesis of polymers of high molar masses. For a better understanding of the mechanism of chain growth under such concentration conditions, the kinetics of polymerization have been investigated with a technique based on adiabatic calorimetry. Sparteine has been found to lack sufficient cation‐binding power to prevent the propagating enolate ion pairs from aggregating. The rate constant of propagation of nonaggregated species has been estimated, as well as the aggregation constant of equilibrium. For very low initiator concentrations, termination reactions have been shown to profoundly alter the control of the polymerization and to prevent a quantitative monomer conversion. Theoretical maximal conversions have been calculated from kinetic data and compare well with the experimental values. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 4964–4975, 2004     

Preparation and characterization of finely dispersed drugs. 5. Ethyl 3,5-di(acetylamino)-2,4,6-triiodobenzoate

Controlled precipitation of the diagnostic imaging agent ethyl 3,5-di(acetylamino)-2,4,6-triiodobenzoate has been used to produce fine particles of various sizes, morphologies, and degrees of crystallinity, which depended on experimental conditions. In addition, two distinct polymorphic forms of the drug have been fully characterized by single crystal X-ray diffraction studies, and evidence for a third polymorph was also observed. Some of the so prepared dry particles were coated with a thin layer of silica.     

Studies on calcium‐containing poly(urethane ether)s

The calcium salt of mono(hydroxyethoxyethyl)phthalate [Ca(HEEP)₂] was synthesized by the reaction of diethylene glycol, phthalic anhydride, and calcium acetate. Calcium‐containing poly(urethane ether)s (PUEs) were synthesized by the reaction of hexamethylene diisocyanate (HMDI) or tolylene 2,4‐diisocyanate (TDI) with a mixture of Ca(HEEP)₂ and poly(ethylene glycol) (PEG₃₀₀ or PEG₄₀₀) with di‐n‐butyltin dilaurate as a catalyst. A series of calcium‐containing PUEs of different compositions were synthesized with Ca(HEEP)₂/PEG₃₀₀ (or PEG₄₀₀)/diisocyanate (HMDI or TDI) molar ratios of 2:2:4, 3:1:4, and 1:3:4 so that the coating properties of the PUEs could be studied. Blank PUEs without calcium‐containing ionic diols were also prepared by the reaction of PEG₃₀₀ or PEG₄₀₀ with HMDI or TDI. The PUEs were well characterized by Fourier transform infrared, ¹H and ¹³C NMR, solid‐state cross‐polarity/magic‐angle‐spinning ¹³C NMR, viscosity, solubility, and X‐ray diffraction studies. The thermal properties of the polymers were also studied with thermogravimetric analysis and differential scanning calorimetry. The PUEs were applied as top coats on acrylic‐coated leather, and their physicomechanical properties were also studied. The coating properties of PUEs, such as the tensile strength, elongation at break, tear strength, water vapor permeability, flexing endurance, cold crack resistance, abrasion resistance, color fastness, and adhesive strength, were better than the standard values. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 2865–2878, 2003     

Heat of adsorption and density distribution in slit pores with defective walls: GCMC simulation studies and comparison with experimental data

The adsorption behavior (capacity, density distribution and packing density) and the isosteric heat versus loading in a slit pore whose walls contain defective graphene layers are investigated in this paper. The defective wall is characterized by the extent and size of the defect. Simulation results obtained with the Grand Canonical Monte Carlo method reveal complex patterns of isosteric heat, and this complex behavior is a result of the interplay between three factors: (i) the surface heterogeneity (solid-fluid interaction, sites with varying degree of affinity), (ii) fluid-fluid interaction and (iii) the overlapping of potentials exerted by the two defective walls. We illustrate this with argon adsorption in pores of various sizes, and results obtained from the simulation agree qualitatively with the experimental data at 77 K on Saran microporous S600H and micro-mesoporous S84 charcoals of Beebe et al. [R.A. Beebe, B. Millard, J. Cynarski, J. Am. Chem. Soc. 75 (1953) 839]. The S600H was found to contain pores predominantly in the neighborhood of 7 Å with 30% of defect and a defective size of 2.84 Å. This is consistent with the argument made by Beebe et al. that this sample is a microporous solid and most pores can accommodate only one layer. The other sample, S84, has larger pores than S600H, and it is found that it has a wider pore size distribution and the pore width is centered at about 12 Å.     

Petrographic/geochemical studies of primary and alteration–weathering minerals in garnetiferous ultramafic xenoliths–basanite, Tartous Province, NW Syria

Kimberlitic–pyropic peridotite–xenolites, probably of Jurassic–Cretaceous age, were found mixed with a younger Upper Tertiary basanitic diabase, as flow texture of plagioclase laths and ilmenite rods around those xenoliths indicated. Mafic–ultramafic rocks were crushed, sheared, and cropped along a creek about 15–18 km NE of the town of Dreikeesh, NW Syria. ⁴⁰K–⁴⁰Ar isotopic dating of a pure fresh black cpx sample, collected from the peridotite xenoliths, yielded an age of about 70 Ma. This age is concurrent to the time when Africa, Eurasia, and America were part of the super continent Pangaea. It also suggests that kimberlite–pyropic peridotitic rocks were located within a cratonic pipe prior to their 2000-km eastward journey (starting from the Mid-Atlantic Rift). Sampled outcrops were located within a ring of about 40 km diameter, considered to be a dome consisting of one or more clusters of kimberlitic pipes. The dome structure, mostly covered with Upper Jurassic–Cretaceous carbonate beds, was tilted westward, and rifted and sheared along its eastern edge. Tilting and crushing were accomplished after the opening of the Red Sea in the Miocene, and the counterclockwise movements of the Arabian plate, which folded the carbonate beds to form the N–S-trending Alawite mountain range along the Syrian coast. Olivine, cpx, and pyrope were the major phases in peridotite. Pyrope, including its Cr–Ni-contents, was found to be the best indicator to decipher the temperature–pressure (T–P) conditions for the system. The inferred temperature was found to be about 1460 °C, at a pressure of 62 kb (around 207 km-depth). Petrographic studies revealed many zoned, resorbed, octahedral and non-metasomatized tiny grains, associated with partly to wholly metasomatized and iddingsitized olivines.     

Structure and defects at Y2BaCuO5 interfaces in melt-textured YBa2Cu3Ox superconductors

Y₂BaCuO₅ (211) inclusions are prominent microstructural features found in melt-textured YBa₂Cu₃O_x (123) superconductors. These particles are of interest because the 123/211 interfaces and the interface-associated defects have been proposed to be flux pinning centers. In addition, the 211 particles are believed to be heterogeneous nucleation centers of dislocation which can increase the critical current density of 123. Unfortunately, only limited studies have been performed on these particles to ascertain their roles in flux pinning. In this investigation, 211 particles, the interfacial structure and defects in undeformed and mechanically deformed melt-textured 123 have been studied by transmission electron microscopy. It was found that there appears to be a preferred orientation between large oblong 211 particles and the 123 matrix. In addition, while the 123/211 interfaces in undeformed 123 are sharp and relatively undistorted, the interfaces in deformed 123 samples are much thicker. Also, the distribution of strained regions and dislocations around oblong 211 particles in undeformed 123 is nonuniform; the interfaces of low surface curvature are relatively free of defects while the surfaces of high curvature are abundant in dislocations. In contrast, the 123/211 interfaces in deformed 123 samples contain high density of dislocations regardless of interface curvature.     

Pulsed gas lenses

The concept of a pulsed gas lens is proposed. Potential applications are envisaged and preliminary experiments with pulsed ray refraction are reported.     

Planned positron experiments at FRM-II

The new research reactor FRM-II near Munich has a strong positron source, which delivers an intense, nearly monoenergetic positron beam. Our positron systems, the pulsed low energy positron source (PLEPS) and the scanning positron microscope (SPM) will be operated at this beam. Some aspects of matching these systems to the new positron source will be discussed.Considerable improvements are expected, e.g. more than 10⁵ s⁻¹ recorded events at PLEPS and sub-micrometre resolution at SPM. They will enable investigations in so far inaccessible problems like the evaluation of annihilation characteristics and trapping constants of individual defects or studies of fast dynamical processes. In applied materials science complex defect structures will be studied which demand a resolution into many differing lifetimes, e.g. fractured specimens, wear, corrosion, etc. Also large series of measurements at small systematic modifications are planned. There is also the opportunity to analyse in addition the chemical microstructure of the specimens by means of a hydrogen microprobe and other ion beam techniques available close to FRM-II at the Technical University of Munich.