TC4钛合金紧固件孔E-I强化研究

 介绍TC4(Ti-6Al-4V)钛合金螺栓孔无衬套冷胀孔干涉配合综合强化的研究结果。实验证明,在给定的条件下,冷胀孔强化的TC4板状空孔试件的疲劳寿命增益系数(LIF)为13,干涉配合螺栓连接的LIF=3,而E-l强化件的疲劳寿命比单纯干涉配合又有成倍提高。电镜断口分析表明TC4合金强化件的疲劳裂纹的形成和扩展与LY12CZ及30CrMnSiA相似,它们不表现为典型的角裂纹,即沿板平面和厚向扩展速率有明显差异。对于TC4合金,在改善疲劳品质上,带衬套冷胀孔强化比无衬套冷胀孔强化好得多。     

异型孔空心叶片壁厚检测的试验研究

发动机叶片的结构型式和制造误差，直接影响发动机的性能和使用寿命。运用超声波法和电涡流法，对两种不同材料和形式的试件进行了试验。电涡流法受到探头直径和试件几何尺寸的影响，测量误差大，超声波法由于存在测量盲区，测量厚度的下限受到限制。但测量值与实际值相关，若对探头加以改进，用于异型孔空心叶片壁厚检测是可行的。     

Spectra and time variability of black-hole binaries in the low/hard state

We propose a jet model for the low/hard state of galactic black-hole X-ray sources which explains the energy spectra from radio to X-rays and a number of timing properties in the X-ray domain such as the time lag spectra, the hardening of the power density spectra and the narrowing of the autocorrelation function with increasing photon energy. The model assumes that (i) there is a magnetic field along the axis of the jet, (ii) the electron density in the jet drops inversely proportional to distance, (iii) the jet is “hotter” near its center than at its periphery, and (iv) the electrons in the jet follow a power-law distribution function. We have performed Monte Carlo simulations of Compton upscattering of soft photons from the accretion disk and have found power-law high-energy spectra with photon-number index in the range 1.5–2 and cutoff at a few hundred keV, power-law time lags versus Fourier frequency with index 0.8, and an increase of the rms amplitude of variability and a narrowing of the autocorrelation function with increasing photon energy as they have been observed in Cygnus X-1. The spectrum at long wavelengths (radio, infrared, optical) is modeled to come from synchrotron radiation of the energetic electrons in the jet. We find flat to inverted radio spectra that extend from the radio up to about the optical band. For magnetic field strengths of the order 10⁵–10⁶ G at the base of the jet, the calculated spectra agree well in slope and flux with the observations.     

飞机数字化装配系统中机身交点孔加工方法研究

针对传统交点孔加工方法加工精度低且存在回弹变形的问题,设计了一种满足飞机大部件数字化装配要求的机身交点孔精加工方法,根据交点孔的加工特性完成了机身定位与固持、数控加工中心定位以及加工工艺的总体设计,确定了交点孔加工程序原点的计算方法和编程原则,最后通过交点孔试切加工试验验证了加工方法的可行性。     

Machining of a film-cooling hole in a single-crystal superalloy by high-speed electrochemical discharge drilling

Single-crystal superalloys are typical advanced materials used for manufacturing aeroengine turbine blades. Their unique characteristics of high hardness and strength make them exceedingly difficult to machine. However, a key structure of a turbine blade, the film-cooling hole,needs to be machined in a single-crystal superalloy; such machining is challenging, especially considering the increasing levels of machining efficiency and quality demanded by the aeroengine industry. Tube electrode high-speed electrochemical discharge drilling(TSECDD), a hybrid technique of high-speed electrical discharge drilling and electrochemical machining, provides high machining efficiency and accuracy, as well as eliminating the recast layer. In this study, TSECDD is used to machine a film-cooling hole in a nickel-based single-crystal superalloy(DD6). The Taguchi methods of experiment are used to optimise the machining parameters. Experimental results show that TSECDD can effectively drill the film-cooling hole; the optimum parameters that give the best performance are as follows: pulse duration: 12 ls, pulse interval: 30 ls, peak current:6 A, and salt solution conductivity: 3 m S/cm. Finally, a hole is machined by TSECDD, and the results are compared with those obtained by electrical discharge machining. TSECDD is found to be promising for improving the surface quality and eliminating the recast layer.     

基于瞬态液晶测量技术的收缩-扩张形孔

采用一种进行全表面测量的瞬态液晶测量技术测量了新型气膜孔(收缩-扩张形孔)的气膜冷却特性,研究了动量比对冷却效率和换热系数的影响,并与传统的圆柱形孔气膜冷却特性进行了对比,结果表明:收缩-扩张形孔中心线附近区域的冷却效率相对较低,而两孔之间区域的冷却效率相对较高,与圆形孔分布规律相反;在上游区域,两孔中间区域的换热系数比相对孔中心线附近区域较高,而在下游区域,两孔中间区域的换热系数比相对孔中心线附近又较低,与圆形孔相比也有较大不同。相对于圆柱形孔,收缩缝形孔的平均换热系数比在上游较高,在下游较低;收缩-扩张形孔喷出气膜对下游壁面区域的有效覆盖率远大于圆柱形孔,其展向平均冷却效率明显高于圆柱形孔;收缩-扩张形孔在动量比为2时的平均冷却效率最高。     

孔间距和前倾角对进出口扩张形气膜孔流量系数的影响(英文)

Discharge coefficients of 3-in-1 hole of three inclination angles and three spacing between holes are presented which described the discharge behavior of a row of holes. The inlet and outlet of the 3-in-1 hole both have a 15° lateral expansion. The flow conditions considered are mainstream turbulence intensities and density ratios of secondary flow to mainstream. The momentum flux ratios varied in the range from 1 to 4. The comparison is made of the discharge coefficients of three shaped holes to find an optimal hole with low flow loss. The results show that the discharge coefficients of 3-in- 1 hole are highest in three shaped holes and therefore this article is focused on the measurements of discharge coefficients of 3-in-1 hole for various geometries and aerodynamic parameters. The measured results of 3-in-1 hole indicate that turbulence intensities, density ratios and momentum flux ratios have weak influence on discharge coefficients for inclination angle of 20°. The high turbulence intensity yields the small discharge coefficients for inclination angle of 45° and 90°. The increased both momentum flux ratios and density ratios lead to the increased discharge coefficients for inclination angle of 45° and 90°. The increased inclination angle causes the rapidly increased discharge coefficients. There is a weak dependence of discharge coefficients on hole pitches.     

基于角运动入流模型的旋翼俯仰状态气动响应计算

利用旋翼弯曲涡管理论模型,并计人涡核修正影响,发展了一个计算角运动对旋翼人流影响的分析方法,并通过该方法计算的旋翼人流分布与实验结果的对比,验证方法的有效性,然后计算了直升机在悬停和前飞时俯仰率对旋翼入流的影响.针对机动飞行时的尾迹畸变效应,对Pitt-Peters动态人流模型进行了增广,并建立了动态的尾迹畸变模型以考虑机动飞行时的尾迹滞后效应,推导了旋翼有角运动时的桨叶挥舞运动方程,并给出了旋翼的平衡分析模型.结合增广的人流模型、尾迹畸变模型、桨叶挥舞运动模型和旋翼平衡分析模型,建立了一个旋翼有角运动时的动态气动响应分析方法,并应用该方法分析了模型旋翼在机动俯仰状态下的旋翼动态挥舞响应和气动力响应.     

出流结构对涡轮叶栅端壁气膜冷却效率数值研究

通过对涡轮叶栅端壁上游不同气膜冷却结构模型进行数值模拟,得到了不同吹风比情况下,涡轮叶栅端壁的流动与换热特性.结果表明:圆柱形孔冷气射流在孔下游与主流相互作用形成一对转动方向相反的耦合涡,对涡轮叶栅端壁的气膜冷却效果不利.前向扩张孔降低了孔下游耦合涡的强度,对涡轮叶栅端壁总体气膜冷却效率要优于圆柱形孔.前向扩张缝结构增大了射流宽度,冷却了孔间端壁,对涡轮叶栅端壁总体气膜冷却效率要优于圆柱形孔和前向扩张孔.      

三角翼大幅度俯仰运动非定常测压实验洞壁干扰研究

用两个几何相似大小不同的前缘后掠角 70°三角翼模型在闭口风洞中进行正弦俯仰振荡实验 ,测量三角翼模型吸力面动态压力以及风洞洞壁上最佳测压点的非定常压力。实验表明 ,三角翼模型在正弦俯仰振荡时 ,其吸力面动态压力以及洞壁上最佳测压点的非定常压力与三角翼模型上的法向力一样呈现迟滞环现象。模型展宽比 (翼展 /洞宽 )增大 ,迟滞环幅度增大 ,动态压力绝对值增大。无论上仰或下俯 ,模型展宽比 (翼展 /洞宽 )增大 ,三角翼模型吸力面涡破碎位置离前缘较远。风洞顶壁上最佳测压点非定常压力迟滞环方向与风洞底壁上对应最佳测压点非定常压力迟滞方向相反。风洞洞壁上最佳测压点非定常压力变化频率与模型正弦俯仰振荡频率一致 ,各最佳测压点间呈现时间延迟现象。