基于矢量平均的信道估计算法

提出一种适用于DS-CDMA无线通信系统的低计算量而性能良好的信道估计算法。在DS-CDMA系统中，当接收信号经过解扩或多用户检测等时域预处理后，可以认为干扰大大减弱、期望信号在处理后的信号中占主要地位。这样，用预处理后信号相关阵的最大特征值对应的特征矢量可以很好地近似期望信号的信道矢量。但是，直接特征分解需要很大的计算量，特征跟踪计算量较低，但瞬态性能较差。本文提出一种基于相关矩阵列矢量平均的信道估计算法，该算法不需要特征分解或跟踪。仿真结果表明：新算法在降低计算量的情况下可以获得同直接特征分解方法几乎相同的性能。     

Chemische Zusammensetzung und Mikrostruktur polymerabgeleiteter Gläser und Keramiken im System Si–C–O. Teil 2: Charakterisierung der Gefügeausbildung mittels hochauflösender Durchstrahlungselektronenmikroskopie und Feinbereichsbeugung

Chemical Composition and Microstructure of Polymer‐Derived Glasses and Ceramics in the Si–C–O System. Part 2: Characterization of microstructure formation by means of high‐resolution transmission electron microscopy and selected area diffraction Liquid or solid silicone resins represent the economically most interesting class of organic precursors for the pyrolytic production of glass and ceramics materials on silicon basis. As dense, dimensionally stable components can be cost‐effectively achieved by admixing reactive filler powders, chemical composition and microstructure development of the polymer‐derived residues must be exactly known during thermal decomposition. Thus, in the present work, glasses and ceramics produced by pyrolysis of the model precursor polymethylsiloxane at temperatures from 525 to 1550 °C are investigated. In part 1, by means of analytical electron microscopy, the bonding state of silicon was determined on a nanometre scale and the phase separation of the metastable Si–C–O matrix into SiO₂, C and SiC was proved. The in‐situ crystallization could be considerably accelerated by adding fine‐grained powder of inert fillers, such as Al₂O₃ or SiC, which permits effective process control. In part 2, the microstructure is characterized by high‐resolution transmission electron microscopy and selected area diffraction. Turbostratic carbon and cubic β‐SiC precipitate as crystallization products. Theses phases are embedded in an amorphous matrix. Inert fillers reduce the crystallization temperature by several hundred °C. In this case, the polymer‐derived Si–C–O material acts as a binding agent between the powder particles. Reaction layer formation does not occur. On the investigated pyrolysis conditions, no crystallization of SiO₂ was observed.     

NMOS器件两次沟道注入杂质分布和阈电压计算

分别考虑了深浅两次沟道区注入杂质在氧化扩散过程中对表面浓度的贡献。对两次注入杂质的扩散分别提取了扩散系数的氧化增强系数、氧化衰减系数和有效杂地系数，给出了表面浓度与工艺参数之间的模拟关系式，以峰值浓度为强反型条件计算了开启电压，文章还给出了开启电压、氧化条件、不同注入组合之间的关系式。     

Breakdown characteristics of oil and paper insulation for a very fast transient voltage

This paper describes the dielectric breakdown characteristics of oil and oil‐impregnated paper for very fast transient (VFT) voltages. Blumlein circuits generate VFT voltages of 60 and 300 ns in a pulse width that simulates disconnecting switching surges in gas‐insulated switch gears. We measured the breakdown voltages of needle‐to‐plane, plane‐to‐plane oil gaps and several pieces of paper between plane electrodes for VFT and lightning impulse voltages. The measured data were formulated in V‐t characteristics and Weibull probability distributions. The inclination n of V‐t characteristics of insulating paper is 150, which is less than n = 13.7 of the plane‐to‐plane oil gap in the VFT time range. The shape parameters of Weibull distribution obtained in this study show that the scattering of breakdown voltages of paper is much less than that of oil. © 2002 Wiley Periodicals, Inc. Electr Eng Jpn, 141(4): 16–24, 2002; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.10043     

Voltage sag compensation with minimum energy injection by use of a micro‐SMES

This paper presents a method to compensate voltage sags with minimum energy injection for a series‐connected voltage restorer using a micro‐SMES. A circuit for extracting the fundamental symmetrical components from sag voltages and a minimum energy injection algorithm is described. Simulations of voltage sag compensation have been carried out using PSCAD/EMTDC for various faults. The simulation results confirm the validity of the proposed method and show the possibility of reducing the size of energy storage devices. © 2002 Wiley Periodicals, Inc. Electr Eng Jpn, 141(3): 70–80, 2002; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.10047     

基于Protel DXP的电路仿真设计

Protel DXP是集所有设计工具于一身的电子设计自动化(EDA)软件.文中运用其内嵌的仿真器叙述了分压式偏置电路放大器的仿真设计过程,设计过程简单、方便.在电子线路理论教学过程中引入电路设计仿真环节在不同情况下对电路进行实时分析,不仅可以提高学生的学习兴趣,而且能够在较短时间内加深学生对理论知识的理解;在工程设计过程中利用仿真工具对电路进行即时测试,可以缩短设计周期,提高设计效率.     

低压直流供电电路中高压直流的产生

在由低压直流电源供电的电路中,往往电路的某些部位需要使用高于电源所供的电压,将电源所供的低压转换为较高的电压,常用的方法有3种:自举升压、电感升压、逆变升压。结合实际应用电路对各种升压方法从器件选择、升压原理、升压结果等诸方面进行分析、探讨,解决了总体供电电压不变时,局部高压产生的关键性问题。它对电子电器电路的设计人员有一定的启发作用,对优化电路、遴选器件有较强的参考价值。     

天津独流减河工程监控系统现地通信单元设计

提出一种配电网电容电流测量的新方法，在零序电压互感器的开口三角侧串联一个可调电感，通过注入一个变频恒流信号寻找配电网的谐振频率，改变可调电感的数值后寻找另一谐振频率，联立2个谐振方程求解电容电流，该方法消除了电压互感器漏抗对测量的影响。开发了配电网电容电流测量仪，经模拟试验和现场测试表明，该方法具有安全、快捷、准确等特点，适用于中性点不接地或经随调式消弧线圈接地配电网。     

锌电积的节电探讨

分析厂影响锌电积电能消耗的因素，提出了锌电积的节电对策与展望。     

数字电位器的应用技术

从应用的角度出发，介绍合理设计应用电路和合理选择数字电位器的种类与型号，来克服数字电位器普遍存在的主要缺点的方法。文章具有较强的针对性和可操作性，对数字电位器的应用实践具有指导作用。