投加聚氨酯泡沫微生物固定化载体的SBBR脱氮除磷实验研究

研究投加聚氨酯泡沫微生物固定化载体的SBBR脱氮除磷效果及机理.在SBR中填充聚氨酯泡沫微生物固定化载体,形成序批式生物膜反应器(SBBR).SBBR以实际生活污水为处理对象,在A/O运行工况下对微生物进行培养驯化,并在SBBR运行稳定时研究其脱氮除磷效果.研究结果表明,SBBR中的聚氨酯泡沫微生物固定化载体在空间上形...     

固定化铜绿假单胞菌生物降解对硝基苯酚

用海藻酸钠作载体,将一株能以对硝基苯酚(PNP)为唯一碳源和氮源的铜绿假单胞菌（Pseudomonas aeruginosa）进行固定化包埋,利用正交试验确定该菌株固定化细胞制备的最优条件,探讨固定化细胞技术对PNP的生物降解效果及其影响因素。结果表明,该菌株的固定化细胞对PNP的生物降解速度大于游离细胞;固定化细胞对PNP的耐受浓度比游离细胞高;固定化细胞生物降解PNP的最适pH为8.0～9.0,最适温度为30～35 ℃。该固定化细胞在PNP浓度为50 mg/L的无机盐溶液中培养42 h,可使PNP降解率接近100%,其生物降解的时间动力学曲线分为0～35 h和35～42 h两段,其中0～35 h为生长延滞期,35～42 h随着菌株生长的开始,PNP迅速被生物降解,约7 h生物降解完全结束。该菌株的固定化细胞可连续使用3次,生物降解效果稳定。     

牛骨粉对Cd污染土壤修复效应和土壤肥力的影响

通过一年静态培养试验,研究了牛骨粉对碱性和酸性Cd污染土壤钝化修复效应及土壤基本理化性质、肥力和酶活性的影响.结果表明,与对照相比,投加牛骨粉后碱性土壤有机质和含水率分别降低了5.4%～14.3%和0.29%～3.04%,而土壤阳离子交换量(CEC)增加了10.8%～18.9%;在酸性土壤中,添加牛骨粉后土壤pH、有机质和CEC分别较对照增加了0.70～1.42、0.4%～6.7%和1.1%～3.4%,含水率则下降了0.75%～2.58%.两种土壤有机碳红外光谱特征峰相似,图谱形状基本一致,但强度存在不同程度的差异.施用牛骨粉后土壤总氮、总磷和全钾含量均有所提高,其中,碱性土壤最大分别增加了39.8%、345.2%和3.4%,酸性土壤最大分别增加了61.0%、612.9%和5.1%.铵态氮、硝态氮、有效磷、速效钾含量均随牛骨粉施加量的增加而增加.土壤中TCLP(toxicity characteristic leaching procedure)提取态Cd含量随牛骨粉投加量增加而降低,与对照相比,酸性和碱性土壤分别减少了38.9%～71.9%和8.6%～18.2%.施加牛骨粉整体上促进了土壤过氧化氢酶、过氧化物酶和尿酶活性(仅碱性土壤脲酶活性受到抑制).在碱性土壤中,土壤有效态Cd含量与pH、有机质、含水率、有效磷和速效钾呈显著正相关(p0.01),而与阳离子交换量、全氮、全磷、过氧化氢酶表现为显著负相关(p0.01).在酸性土壤中,土壤有效态Cd含量与pH、有机质、全氮、全磷、全钾、有效磷、速效钾、过氧化氢酶、过氧化物酶呈显著负相关(p0.01),而与含水率呈显著正相关(p0.01).综合评价表明,采用牛骨粉原位钝化修复Cd污染土壤有效可行.     

两种铁基材料对污染农田土壤砷、铅、镉的钝化修复

制备得到了铁钙（FeCa）和铁锰（FMBO）两种铁基材料,用于钝化修复As、Pb和Cd污染土壤.研究采集了来自绍兴上虞（SY）、广东佛山（FS）、广东韶关（SG）、湖南浏阳（LY）、江西赣州（GZ）、贵州独山（DS）和安徽马鞍山（MAS）的7种重金属污染水稻土（潮泥土）,通过土壤培养试验,研究铁钙材料（FeCa）和铁锰材料（FMBO）对各类土壤溶液中As、Pb和Cd浓度动态变化的影响,对土壤中有效态As、Pb和Cd钝化效果的影响,以及在不同种类土壤中有效态As、Pb和Cd钝化效果差异及影响因素.结果表明,培养过程中,铁基材料处理下土壤溶液中As、Pb和Cd浓度均低于对照处理.研究发现,两铁基材料均能对土壤中As、Pb和Cd起到较好的钝化作用,相同添加量下,铁钙材料对土壤As的钝化效率优于铁锰材料,而材料之间对土壤Pb和Cd钝化效率无显著差异.铁钙材料处理下各种土壤As钝化效果表现为GZ > SG > DS和MAS,土壤铅钝化效果表现为FS>SY、LY和SG>MAS,土壤镉钝化效果表现为SY、GZ和DS>MAS;铁锰材料处理下各种土壤As钝化效果表现为SY、LY和GZ > DS > FS,土壤Pb钝化效果表现为FS > GZ > SY,土壤Cd钝化效果表现为DS > LY > MAS.各种土壤As钝化效率在两铁基材料处理下均与土壤黏土含量呈显著负相关,各种土壤Pb钝化效率在两铁基材料处理下均与土壤pH呈显著正相关,各种土壤Cd钝化效率在铁钙材料处理下与土壤黏土含量显著负相关.总体来看,两铁基材料均适用于各不同种类As、Pb和Cd污染土壤的治理.     

微生物固定化技术在污水生物脱氮中的应用

综述了微生物固定化技术在污水硝化、生物脱氮中的应用,包括固定化材料与固定化工艺;国内外研究与应用现状;以及在较大规模污水处理中的实际应用;对该项技术目前存在的问题及其解决途径、发展前景和趋势进行了评述。     

钙、氯对磷酸盐稳定污染土壤中铅的促进作用研究

为探讨促进磷酸盐稳定污染土壤中铅的方法,在全铅含量为517 mg·kg-1的铅冶炼污染土壤中加入5 mmol·kg-1磷酸盐,同时加入10mmol·kg-1硝酸钙或5 mmol·kg-1氯化钾,在15%或30%的含水率下培养40 d,之后种植黑麦草.结果表明,与单独施用磷酸盐相比,采用磷酸盐与钙、氯结合或增加培养期间的土壤含水率后,土壤DTPA-Pb含量下降3.92%~26.1%;对于同一添加剂处理,培养期间土壤含水率从15%增加到30%,土壤有效铅(DTPA-Pb)含量下降8.83%~24.4%.增加土壤含水率后,土壤有效磷(Olsen-P)含量均显著升高(p0.05).土壤铅的EXAFS分析表明,与未施用磷酸盐的对照相比,土壤中加入磷酸盐后矿物态铅的比例由57%上升至81%,加施钙、氯或增加土壤含水率后,多数处理矿物态铅的比例有所下降,而有机结合态铅比例上升.与对照相比,污染土壤中施用磷酸盐后,植物产量大幅增加,但施用钙、氯或增加培养期间含水率后,部分处理植物产量有所下降.以上结果表明,在铅冶炼污染土壤中加入磷酸盐时,加入钙、氯或者增加土壤含水率均有利于铅的稳定,但以上措施可能对植物生长产生不利影响.     

固定化反硝化聚磷菌同步除磷脱氮实验研究

实验采用海藻酸钠和PVA添加膨润土包埋固定经富集驯化的以反硝化聚磷菌(DNPAOs)为主的活性污泥,利用体视显微镜和扫描电子显微镜考察了固定化小球的形态和表面结构,并对厌氧/好氧条件下,包埋小球除磷脱氮性能进行探讨,结果表明:固定化小球具有良好的强化生物除磷和较好的反硝化脱氮性能,体系的COD去除率平均达74.9%,平均除磷效率为95.3%,氨氮平均去除率达到95.2%左右。小球若长时间缺氧,在其内部会出现厌氧区,并产生厌氧放磷现象。     

Modelling N mineralization from green manure and farmyard manure from a laboratory incubation study

Predicting N mineralization from organic manures like farmyard manure (FYM) is more difficult than from fresh organic materials like crop residues, as the manures vary greatly in composition. A laboratory incubation experiment was carried out for 98 days at 30 °C under aerobic conditions to study the effects on N dynamics of Gliricidia (Gliricidia sepium, Jacquin) and FYM application to soil at 5 and 10 g kg⁻¹. Application of Gliricidia induced N mineralization from the start of incubation period, with the amount of N mineralized increasing with rate of application. In contrast, application of FYM resulted in immobilization of mineral N in soil, irrespective of the rate of application. The initial net immobilization from FYM was limited by availability of N in the soil for the higher rate of application.We used the APSIM SoilN module to simulate these contrasting patterns of mineralization of N from Gliricidia and from FYM. The prediction of N mineralized from Gliricidia was better than FYM. The default model parameters specify that the fresh organic matter pools (FPOOL1, FPOOL2 and FPOOL3) have the same C:N ratio and this assumption was ineffective in predicting N mineralized from FYM. The predictive ability of the model improved when this default assumption was modified based on the size of the individual pools (FPOOL1, FPOOL2 and FPOOL3), and the pool's C:N ratios. The modelling efficiency, a measure of goodness of fit between the simulated and observed data, improved markedly for the modified model. The discrepancy between the modelled and observed data was a tendency for the model to underestimate the rate of re-mineralization at the lower rate of application of FYM in the later part of incubation. Unfortunately the appropriate modification to the size and C:N ratios of the FPOOLs could not be determined on the basis of chemical analysis alone. Thus, a true predictive application of the model to a new FYM material is not yet possible.     

Effect of Cell-to-matrix Ratio in Polyvinyl Alcohol Immobilized Pure and Mixed Cultures on Atrazine Degradation

Atrazine biodegradation by immobilized pure and mixed cultures was examined. A pure atrazine-degrading culture, Agrobacterium radiobacter J14a (J14a), and a mixed culture (MC), isolated from an atrazine-contaminated crop field, were immobilized using phosphorylated-polyvinyl alcohol (PPVA). An existing cell immobilization procedure was modified to enhance PPVA matrix stability. The results showed that the matrices remained mechanically and chemically stable after shaking with glass beads over 15 days under various salt solutions and pH values. The immobilization process had a slight effect on cell viability. With the aid of scanning electron microscopy, a suitable microstructure of PPVA matrices for cell entrapment was observed. There were two porous layers of spherical gel matrices, the outside having an encapsulation property and the inside containing numerous pores for bacteria to occupy. J14a and MC were immobilized at three cell-to-matrix ratios of 3.5, 6.7, and 20 mg dry cells/mL matrix. The atrazine biodegradation tests were conducted in an aerobic batch system, which was inoculated with cells at 2,000 mg/L. The tests were also conducted using free (non-immobilized) J14a and MC for comparative purpose. The cell-to-matrix ratio of 3.5 mg/mL provided the highest atrazine removal efficiency of 40–50% in 120 h for both J14a and MC. The free cell systems, for both cultures, presented much lower atrazine removal efficiencies compared to the immobilized cell systems at the same level of inoculation.     

TiO2-PTFE光催化膜的制备及性能

以聚四氟乙烯（PTFE）乳液和纳米TiO2粉末为原料,采用无水乙醇为溶剂,经辊压后与不锈钢网结合,制备了多孔固定化TiO2-PTFE光催化膜。膜性能研究结果表明,m（TiO2）：m（PTFE）=4时,光催化反应处理质量浓度为20mg／L的苯甲酸溶液,2h内TOC去除率高达81．3％。通过扫描电子显微镜观察,TiO2-PTFE光催化膜表面平整,且孔隙分布均匀。TiO2最佳负载量为15mg／cm2。在优化反应条件下同悬浮态TiO2光催化反应体系相比,TiO2-PTFE光催化膜对光源有更高的利用率,表现出更佳的催化活性。