Seismic response predictions of multi‐span steel bridges through pushover analysis

In the new trend of seismic design methodology, the static pushover analysis is recommended for simple or regular structures whilst the time‐history analysis is recommended for complex structures. To this end, the applicable range of the pushover analysis has to be clarified. This study aims at investigating the applicability of pushover analysis to multi‐span continuous bridge systems with thin‐walled steel piers. The focus is concentrated on the response demand predictions in longitudinal or transverse directions. The pushover analysis procedure for such structures is firstly summarized and then parametric studies are carried out on bridges with different types of superstructure‐pier bearing connections. The considered parameters, such as piers' stiffness distribution and pier–0.5ptdeck stiffness ratio, are varied to cover both regular and irregular structures. Finally, the relation of the applicability of pushover analysis to different structural formats is demonstrated and a criterion based on the higher modal contribution is proposed to quantitatively specify the applicable range. Copyright © 2003 John Wiley & Sons, Ltd.     

RC框架结构直接基于位移的抗震优化设计方法

探讨了静力弹塑性分析验证过程中遇到的几种情况及其产生原因,指出建筑结构设计方案在基于位移的抗震设计中的重要性。从框架结构的侧移模式出发,导出结构一定性能水平的目标顶点位移,建立结构目标顶点位移与等效位移的关系式,根据位移反应谱,由等效位移推出框架结构在各性能水平的目标周期。然后,由pushover曲线确定结构刚度退化机理,导出结构各性能水平相应的自振周期比例关系,根据结构各性能水平自振周期与目标周期的关系确定结构最优设计方案。通过例题加以验证,说明了此设计方法的可行性。     

钢筋混凝土框架结构抗震超强系数分析

基于我国建筑抗震规范要求设计的14栋代表不同抗震特征要求的多高层规则钢筋混凝土框架,通过静力弹塑性分析详细地评估了框架结构的体系超强能力。分析中采用与抗震规范等效静力地震作用效应分布模式相同的单调递增侧向荷载,以二维平面框架为分析对象。分析结果表明地震分区对超强系数的影响较大;有填充墙框架比无填充墙框架的超强能力明显要大;内框架的超强能力比外框架的超强能力大;超强系数随框架楼层数的增加而减小。     

南海某导管架海洋平台倒塌分析

针对在役老龄导管架平台进行倒塌计算分析,确定极限承载力进而评估老龄导管架的安全裕度。采用非线性有限元方法,考虑平台的波流载荷及桩-土的非线性相互作用,利用SACS软件建立导管架整体三维有限元计算分析模型,并用逐步加载的方式,对南海某导管架平台进行了全过程非线性倒塌分析。计算分析表明,该导管架平台极限强度很高,具有较大的安全裕度;导管架倒塌过程呈逐步破坏形式,先是撑杆屈服,造成局部结构破坏,然后是钢桩发生屈服,降低结构承载力,最后节点逐步失效,造成结构倒塌。揭示了导管架平台结构失效倒塌的机理,给出了倒塌分析的可行方法和步骤。     

Performance‐based design using structural optimization

A new methodology for seismic design is proposed based on structural optimization with performance‐based constraints. Performance‐based criteria are introduced for the seismic design of new buildings. These criteria are derived from the National Guidelines for Seismic Rehabilitation of Buildings (Reference [19], Federal Emergency Management Agency (FEMA), ‘NHERP Guidelines for seismic rehabilitation of buildings’, Report Nos 273 and 274, Washington, DC, 1997) for retrofitting existing structures. The proposed design methodology takes into account the non‐linear behaviour of the structure. The goal is to incorporate in the design the actual performance levels of the structure, i.e. how much reserve capacity the structure has in an earthquake of a given magnitude. The optimal design of the structure minimizes the structural cost subjected to performance constraints on plastic rotations of beams and columns, as well as behavioural constraints for reinforced concrete frames. Uncertainties in the structural period and in the earthquake excitation are taken into account using convex models. The optimization routine incorporates a non‐linear analysis program and the procedure is automated. The proposed methodology leads to a structural design for which the levels of reliability (performance levels) are assumed to be quantifiable. Furthermore, the entire behaviour of the structure well into the non‐linear range is investigated in the design process. Copyright © 2000 John Wiley & Sons, Ltd.     

Nonlinear analysis of masonry structures using fiber-section line elements

For seismic analysis of unreinforced masonry (URM) buildings characterized by a box-like behavior, a widely accepted model is based on the equivalent frame idealization of walls. The equivalent frame model uses 1D elements to represent the vertical piers and horizontal spandrels which are connected by rigid nodes. The mechanical characterization of the elements is one of the crucial aspects to predict reasonably the building seismic behavior. Through the comparison with pseudo-static and dynamic experimental tests performed on two-story full-scale buildings, this paper validates the frame modeling in the OpenSees framework, which includes a fiber-section force-based beam element for the axial-flexural behavior, coupled with a cyclic shear-deformation phenomenological law.     

An adaptive capacity spectrum method for assessment of bridges subjected to earthquake action

Estimating seismic demands on structures, to predict their performance level with confidence, requires explicit consideration of the structural inelastic behaviour: to this end, the use of nonlinear static procedures is inevitably going to be favoured over complex nonlinear time-history methods. The currently available assessment procedures have been tested predominantly against building frames. A newly derived assessment procedure is proposed within the scope of bridge applications, based on an innovative displacement-based adaptive pushover technique. The procedure, which can be incorporated into a performance-based engineering philosophy, is applicable to MDOF continuous span bridges with flexible or rigid superstructures, and for varying degrees of abutment restraint. As a first application to determine the viability of the proposed procedure, a parametric study is conducted on a ensemble of bridges subjected to earthquake motion. It is shown that, compared to the seismic demand estimated by means of the more accurate nonlinear dynamic analysis tool, the novel static assessment method can lead to the attainment of satisfactory predictions, both in terms of displacement as well as moment demand on members.     

Pushover analysis procedure for systems considering SSI effects based on capacity spectrum method

This paper presents a new procedure to transform an SSI system into an equivalent SDOF system using twice equivalence. A pushover analysis procedure based on the capacity spectrum method for buildings with SSI effects （PASSI） is then established based on the equivalent SDOF system, and the modified response spectrum and equivalent capacity spectrum are obtained. Furthermore, the approximate formulas to obtain the dynamic stiffness of foundations are suggested. Three steel buildings with different story heights （3, 9 and 20） including SSI effects are analyzed under two far-field and two near-field historical records and an artificial seismic time history using the two PASSI procedures and the nonlinear response history analysis （NLhRHA） method. The results are compared and discussed. Finally, combined with seismic design response spectrum, the nonlinear seismic response of a 9-story building with SSI effects is analyzed using the PASSI procedures, and its seismic performance is evaluated according to the Chinese ＇Code for Seismic Design of Buildings. The feasibility of the proposed procedure is verified.     

Soil–structure interaction effects observed in the in situ forced vibration and pushover tests of school buildings in Taiwan and their modeling considering the foundation flexibility

In the conventional structural seismic analysis, the rigid base model is usually adopted without considering the flexibility of the ground, leading to inaccurate estimation of the vibration characteristics and the seismic response of the structure. In 2007, several in situ tests were conducted by the National Center for Research on Earthquake Engineering (NCREE) on the school buildings in the Guanmiao Elementary School in Tainan, Taiwan. For the study of soil–structure interaction (SSI) effects, the forced vibration test (FVT) was performed, and the deformation of the foundation system was measured during the pushover test. In this paper, the results of these in situ tests are presented and discussed, and the finite element models of the school buildings were generated for the simulation of the FVT and for the pushover analysis in order to investigate the difference between the rigid base model and the flexible base model. Results show that the mechanical properties of the structure and the foundation could be demonstrated in these in situ tests. Additionally, the introduction of the flexibility of the foundation has a considerable influence on the results of structural analysis. Copyright © 2009 John Wiley & Sons, Ltd.     

Estimation of hysteretic energy demand using concepts of modal pushover analysis

Hysteretic energy dissipation in a structure during an earthquake is the key factor, besides maximum displacement, related to the amount of damage in it. This energy demand can be accurately computed only through a nonlinear time‐history analysis of the structure subjected to a specific earthquake ground acceleration. However, for multi‐story structures, which are usually modeled as multi‐degree of freedom (MDOF) systems, this analysis becomes computation intensive and time consuming and is not suitable for adopting in seismic design guidelines. An alternative method of estimating hysteretic energy demand on MDOF systems is presented here. The proposed method uses multiple ‘generalized’ or ‘equivalent’ single degree of freedom (ESDOF) systems to estimate hysteretic energy demand on an MDOF system within the context of a ‘modal pushover analysis’. This is a modified version of a previous procedure using a single ESDOF system. Efficiency of the proposed procedure is tested by comparing energy demands based on this method with results from nonlinear dynamic analyses of MDOF systems, as well as estimates based on the previous method, for several ground motion scenarios. Three steel moment frame structures, of 3‐, 9‐, and 20‐story configurations, are selected for this comparison. Bias statistics that show the effectiveness of the proposed method are presented. In addition to being less demanding on the computation time and complexity, the proposed method is also suitable for adopting in design guidelines, as it can use response spectra for hysteretic energy demand estimation. Copyright © 2008 John Wiley & Sons, Ltd.