Allelopathic effects of giant foxtail on germination and radicle elongation of loblolly pine seed

Water extracts of giant foxtail grass inhibited germination and radicle elongation of loblolly pine seed in a laboratory test. Most of the toxic effects came from extracts of dried foxtail tops, with lesser amounts from fresh tops and roots. Soil texture affected the phytotoxicity of the extracts. Eight chemical compounds known to be phytotoxins inSetaria were identified in extracts of foxtail leaves but could not be found in soil samples under the leaves.     

Numerical analyses of high‐beta spherical tokamaks with varied elongation

The effect of plasma elongation on the second‐stable spherical tokamak (ST) was numerically studied using the experimentally measured pressure and current profiles of ultrahigh‐beta STs. The maximum beta of ST over 50% was obtained in the TS‐3 ST/CT experiment by applying an external toroidal field to an FRC. It was found that the marginal beta for the ballooning instability increased with the plasma elongation κ of ST. The elongated STs with κ > 2 have the magnetic shear (S)–pressure gradient (α) profiles located in the second‐stable regime for the ballooning mode and the stability margin increased with κ. The close relation between the absolute minimum‐B profile and the second stability was documented. The effect of elongation on maximum beta was observed to saturate when κ exceed 3, indicating that the optimized elongation for high‐beta STs is located around 2 < κ < 3. © 2006 Wiley Periodicals, Inc. Electr Eng Jpn, 155(4): 1–6, 2006; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20132     

Evidence of thermally induced borehole elongation: a case study at Soultz, France

When they occur, borehole breakouts are considered strong markers of principal stress directions at depth. An innovative processing method for automatically identifying breakouts from ultrasonic borehole wall images has been developed. It has been applied to data sets from two deep, sub-vertical wells (GPK1 and GPK2) at the Soultz geothermal site in eastern France. In well GPK1, below 3 km depth, compression breakouts, with a 95°±7° azimuth, increasingly occur with depth. They result from time dependent compression failure at sub-critical stress levels and are indicators of the minimum horizontal principal stress orientation. However, in the uppermost logged section of well GPK2 (1.6–2.9 km depth), continuous borehole elongations share roughly the same azimuth with so called drilling-induced fractures (164°±18° and 175°±17° azimuth, respectively). Both features concomitantly vanish with depth, together with the amplitude of the thermal perturbation induced by drilling. It is proposed that these latter borehole elongations result from a pervasive, cooling-induced, tensile micro-cracking process prior to macroscopic failure localization. They are termed thermal elongations and are indicators of the maximum horizontal principal stress orientation. Had a simple logging caliper tool been used for this work, these thermal elongations might have been confused with classical compression breakouts. A simple criterion for differentiating compression breakouts from thermal elongation is proposed.     

Development of temperature compensated high elongation resistance strain gauges for use up to 250°C

The paper describes the development and evaluation of temperature compensated high elongation resistance strain gauges for use from room temperature to 250°C. These gauges could be temperature-compensated on steels with coefficient of thermal expansion α = 11 ppm/°C. Thermal output within 250°C was about 1 μm/m/°C and maximum standard deviation of 5 gauges was 34 μm/m. Strain limit was > 4% at room temperature and at 250°C. Gauge factors of different strain ranges at R.T. and at 250°C are tabulated. Some applications are stated.     

工字钢腿腰延伸系数均匀分配的计算方法

对轧制工字钢采用一种新的腿腰划分方法，用计算机迭代计算，使腿腰延伸系数趋于均匀更趋于实际，使孔型设计更为合理。     

Antisense Oligonucleotide-Based Rescue of Aberrant Splicing Defects Caused by 15 Pathogenic Variants in ABCA4

The discovery of novel intronic variants in the ABCA4 locus has contributed significantly to solving the missing heritability in Stargardt disease (STGD1). The increasing number of variants affecting pre-mRNA splicing makes ABCA4 a suitable candidate for antisense oligonucleotide (AON)-based splicing modulation therapies. In this study, AON-based splicing modulation was assessed for 15 recently described intronic variants (three near-exon and 12 deep-intronic variants). In total, 26 AONs were designed and tested in vitro using a midigene-based splice system. Overall, partial or complete splicing correction was observed for two variants causing exon elongation and all variants causing pseudoexon inclusion. Together, our results confirm the high potential of AONs for the development of future RNA therapies to correct splicing defects causing STGD1.     

Preparation of High Strength and Toughness Aramid Fiber by Introducing Flexible Asymmetric Monomer to Construct Misplaced-Nunchaku Structure

High performance fibers with high strength and toughness have great potential in composites, but contradiction between tensile strength and elongation at break makes the preparation to become a current challenge. Herein, an asymmetric structure of more flexible diamine, 3,4′-diaminodiphenyl ether (3,4′-ODA), is introduced into heterocyclic aramid (PBIA) fibers to replace rigid symmetric p-phenylenediamine (PDA). By studying the properties of copolymer (mPEBA) fibers with different ratios of diamine, it is found that the mPEBA fiber reached the optimal mechanical properties with the 30% content of 3,4′-ODA. Compared with homopolymerized heterocyclic aramid fibers, the tensile strength and elongation at break of mPEBA fiber are improved by 26.2% and 38.7%, respectively. Results of X-ray diffraction show that the introduction of 3,4′-ODA structure can increase stretchability of mPEBA fibers, improving the orientation degree during hot-drawing. Molecular dynamics simulations confirm that 3,4′-ODA structure undergoes a conformation transformation to form a straightened chain during hot-drawing, while symmetrical 4,4′-diaminodiphenyl ether (4,4′-ODA) cannot form the same conformation. The misplaced-nunchaku structure is formed based on the special meta-para position of 3,4′-ODA, achieving the synergy of high strength and high toughness.     

16MnR 容器板性能不合格的原因

运用扫描电镜、金相检验和力学检验对不合格的16MnR容器板进行了检验分析。结果表明，材料中的条状MnS夹杂物和少量的马氏体、贝氏体组织是导致钢板延伸、冲击性能不合格的主要原因。     

钛制容器产品试板压弯角度的探讨

针对钛制容器产品试板弯曲角度按现行标准执行中出现的问题，从力学角度进行探讨，导了了试板压弯对所采用的压头直径与试板厚度和延伸率的关系，即Ｄ〉（１／δ－１）ｔ，并提出了设定试板弯曲压头直径的新思路。     

涤纶低弹网络丝拉伸断裂性能表征

研究在不同的夹持距离、不同拉伸速率条件下涤纶低弹网络丝机械性能 ,从实验结果得知 ,在相同拉伸速率下 ,断裂强力随夹持距离的增加呈对数关系减少。在相同夹持距离下 ,随着拉伸速率的提高 ,平均断裂强力提高 ,断裂伸长增大 ,断裂比功也增大。