声波测井换能器激发响应实验研究

声波测井换能器的激发响应由换能器振动时所表现出来的动态阻抗和激发电路参数决定。而换能器的动态（阻抗）参数随压电晶体及其装配方式（力学边界条件）改变。为了测量换能器动态参数的影响，采用声波测井仪器常用的压电晶体和升压变压器，通过改变激发脉冲宽度和直流电压进行了实验，结果发现：在换能器两端的瞬态响应中，一共有三个二阶网络响应，分别对应于不同的频率。最低的一个影响声波测井波形的基线、与换能器主频接近的一个决定激发效率以及电路与压电晶体之间的匹配关系，是激发电路设计中比较关键的，其参数可以通过导纳圆测量仪器得到。     

有互感和电源的电容耦合电路的量子涨落

通过正则变换和幺正变换的方法研究了有互感和电源存在的情况下的介观电容耦合电路的量子涨落。结果表明电荷和电流的量子涨落与电源无关。当电路元件确定时，如果L1／L2的值很大或很小，耦合对涨落的影响很大。互感从有到无的过程中，回路1中电流的涨落和回路中2中电荷的涨落有明显的变化。换句话说，互感的有无对涨落的大小起着举足轻重的作用。     

超宽带极窄脉冲设计与产生

超宽带(UWB)技术是以持续时间极短的脉冲作为传输载体进行数据通信的无线新技术。基于BJT雪崩特性,本文采用并行同时触发的工作方式,设计并产生了高重复速率的UWB脉冲电路发生器,极大地减少了时延,缩短了上升时间,提高了脉冲的幅度,并从等效电路法的观点分析计算了脉冲的特性参数,理论结果与实测结果具有较好的一致性。     

可编程模拟器件与技术新进展

简述可编程模拟器件的基本原理、典型应用和开发方法,介绍并比较主要的模拟可编程实现技术与主流器件系列,指出现存的主要问题并展望其未来发展方向.     

Generation of Technology-Independent Retargetable Analog Blocks

This paper introduces a complete methodology for retargeting of analog cells to different sets of specifications. This methodology is technology-independent, thus allowing the migration, from one technology to another, of the circuit under retargeting. Careful integration of the device sizing and layout generation tasks via the incorporation of layout constraints during the sizing process allows to generate fully functional designs in a few minutes. The methodology is illustrated via the retargeting of a fully-differential Miller-compensated two-stage operational amplifier for a new set of specifications and two different technological processes.An erratum to this article can be found at     

基于IP核复用技术的SoC设计

概述了国内外IP产业的发展情况,论述了我国发展IP核复用技术SoC设计的可能性和必要性,指出我国急需发展的关键芯片及IP核种类.     

一种动态开关电容运算放大器共模负反馈电路

本文主要介绍了一种应用于Cascode结构运放中的开关电容共模负反馈电路，它具有稳定性好、对运放频率特性影响小、不消耗额外功率等优点。对电路运用Hspice进行了模拟，并给出了模拟结果。     

幅频特性的数学分析

根据数控装置检测系统中传感器信号电路工作要求,以共射电压放大电路为例,分别考虑耦合电容、旁路电容、结间电容和分布电容对不同信号频率的作用,分析了电路的低频特性和高频特性,给出了上下限截止频率的解析式.由此得出,电路其他参数一定时,在低频段,下限截止频率与耦合电容、旁路电容成反比,在高频段,上限截止频率与等效输入输出电容成反比,从而为传感器系统设计提供理论依据.     

Integrated Smart Sensor Calibration

In many applications electronic sensors are used toimprove performance and reliability of measurement systems. Suchsensors should provide a correct transfer from the physical signalto be measured to the electrical output signal. One importantstep to achieve this, is to calibrate each sensor by applyingdifferent reference input signals and adjusting the sensor transferaccordingly. Besides expensive reference equipment the calibrationprocess takes much time and attention per individual sensor,which means a considerable increase in sensor production costs.By including at the sensor or sensor interface chip a programmablecalibration facility the calibration of such smart sensors caneasily be automated and can be executed for a batch of sensorsat a time, thus minimizing the calibration time and costs. Thispaper presents a calibration method and options for integrationin the smart sensor concept, in hardware as well as in software.An advantage of the proposed method is that it does not needa large matrix of calibration data, which needs to be storedin a look-up table or converted into a correction formula, butinstead it uses a step-by-step approach to correct the sensortransfer at each calibration measurement until the error is sufficientlysmall.     

起重机吊钩拖动绕线电动机他励双高调速系统

本文提出励磁电流可自动控制的他励式双高调速系统设计方案。系统在提升特别是在下放重物时，具有较硬的机械性；在负载１０－１００％的变化范围内，可实现最大偏差Δｎｍａｘ／ｎｍｉｎ１００％≤１０％，调速范围Ｄ≥１０；在满载运行条件下，可节约电能８０％以上。