稳态锁模产生4ps激光脉冲

首次利用ＧａＡｓ光电导开关，控制Ｎｄ：ＹＬＦ激光器腔内Ｑ值，实现稳态锁模，获得脉宽和能量稳定性极高的４ｐｓ激光脉冲。     

Effect of the geometry of workpiece on polishing velocity in free annular polishing

Base on Coulomb friction model, the workpieces with different geometry rotating in free annular polishing are simulated. From simulation, the following conclusions are drawn. The angular velocity of workpiece is higher than that of polishing pad if the ring rotates uncontrolled in free annular polishing. The circular workpiece can synchronize with polishing pad through controlling the rotation of ring, which depends on the radii of ring and workpiece, the friction coefficients of polishing pad-workpiece and ring-workpiece, and the angular velocity of polishing pad. The workpiece with sharp corner cannot contact with the ring contiguously, which causes the contact state changing and the angular velocity of workpiece fluctuating ceaselessly, and this type of workpiece should be controlled with clamp to rotate synchronistically with the polishing pad.     

抛光粉颗粒度对高功率激光玻璃材料抛光效率和粗糙度的影响

磷酸盐钕玻璃、熔石英和BK7是3类用于激光惯性约束聚变(ICF)装置主要光学元件材料.实验中采用不同平均粒径的氧化铈抛光粉对上述3类材料分别进行抛光,对特定材料抛光去除量和抛光粉平均粒径的关系进行了研究.实验表明:由于材料的物理和化学特性不同,特定的材料需选用相应平均粒径大小的抛光粉才能达到最佳的抛光效率.实验还就上述3类高功率激光玻璃材料抛光中各个阶段的抛光粗糙度与抛光粉平均粒径的关系进行了研究,结果表明:某一规格抛光粉的粒径对不同特性材料抛光后的表面粗糙度影响表征情况不同.     

脉冲压缩光栅光路调节新方法研究

介绍了一种简单而实用的大口径脉冲压缩光栅光路调节方法,有效解决了普通光路调节方法中轴向调节精度不高的问题。首先由全息透镜(光栅)成像公式出发,推导出了该光路调节的基本原理。并从光栅记录系统与光栅衍射波像差的关系,结合初级像差理论推导得出叠栅条纹像差为0.4786λ,大约是光栅衍射波像差(0.25λ)的两倍,利用此关系也可对光栅衍射波像差进行实时监测。从数值模拟结果可知,利用叠栅条纹法调节光路可将光栅波像差减至0.06λ,相应的轴向误差量为0.007 mm,可有效提高了轴向调节精度。     

复合折射棱镜的色散研究

理论分析用二种不同材料组成复合色散棱镜的色散量，提出变相色散棱镜，以增大色散量。结论在实验中得到验证。     

成组设计在高功率激光装置中的应用

在高功率激光装置研制中首次引入成组技术概念,并以空间滤波器为例论证了在高功率激光装置的器件研制过程中实施成组设计的必要性和可行性最后讨论了计算机辅助成组设计系统(GTCAD)的组成和在高功率激光装置中具体实施过程.     

双菱体λ/4消色差相位延迟器的设计

根据菲涅尔全内反射相变理论,给出了双菱体λ/4消色差器的结构设计、性能分析和测量方法.由有效通光孔径和光线追迹设计出BK7玻璃在波长532 nm时相位延迟λ/4的双菱体的结构,用作532 nm至1 064 nm波长范围的标准λ/4相位延迟器.理论分析了入射角变化和波长变化对双菱体相位延迟的影响,当入射角变化限制在±4.3°以内时,其影响得到补偿;波长从532 nm到1 064 nm产生的误差为－0.65°.采用椭偏法中的消光技术,分别实测了双菱体在532 nm和1 064 nm波长下的相位延迟为：90.08±0.14°和88.99±0.1°,可知两不同波长产生的相位延迟误差为－1.09°.     

高功率激光装置光束准直系统新型远场监测技术

利用高功率激光装置空间滤波器小孔成像和取样光栅的衍射,设计出一套新型光路远场监测方案,并且在实验平台上进行了实验验证.实验结果表明：相对传统的远场监测方法,该远场监测系统通过侧面离轴光栅取样灵活利用空间,其调整平均误差为空间滤波器小孔直径0.9%,能够满足准直系统远场调整精度(<小孔直径5%)的要求. 关键词： 激光技术 光束准直 光栅 远场     

Optimization of compensation for high spatial frequency in distorted wavefront using optical phase conjugation

A method is proposed to optimize the recording structure of the photorefractive volume grating to compensate high spatial frequency in the distorted wavefront by optical phase conjugation. Based on the coupled-wave equation, the diffraction efficiency of the recorded grating formed by the scattered beams in different recording structures is simulated. The theoretical results show that the recorded modulations with high spatial frequency can be significantly improved in the small recording angle. In the experiment, three recording structures with the recording angles of 7.5°, 30°, and 45° are chosen to verify the compensation effect. Compared with the reconstructed image in the large recording angle of 45°, the signal to noise ratio of the image recorded at 7.5° increases to 3.2 times of that at 45°.     

数字全息中再现像分离问题的研究

详细分析了数字全息的再现像分离条件,指出数字全息和普通全息的再现像分离条件之间的区别,同时也讨论了再现条件对数字全息记录光路的要求,同时给出一种能部分避免再现像重叠的处理方法,并做出相应的实验验证.