电磁超声流量计的研制

基于电磁声换能器的原理，研制了一种新型的电磁超声流量计，并讨论提高测量精度的措施。     

燕皮传统加工工艺中碱液对肉糜特性的影响

燕皮是以猪肉和甘薯粉为原料,手工制成的薄如纸且经煮不烂的传统食品。在传统制作燕皮过程中添加山榉灰配制的碱液是影响肉糜品质的关键步骤。通过测定制作燕皮过程中各工序样品的氮溶解指数、持水性、乳化稳定性、pH值和粘度,利用SDS-PAGE分析样品中的蛋白质组分、利用光学显微镜观察它们的结构变化,证实植物碱液能够提高样品的氮溶解指数、持水性和乳化稳定性并且延迟了肉糜硬化。同时实验证明碳酸碱(Na2CO3或K2CO3)可替代传统工艺中的植物碱,为后续标准化、工业化生产提供可行条件。     

NSA-500-1型氩弧焊机VD9不同接法对引弧和稳弧的影响

从一起NSA－500－1型氩弧焊机故障，分析其高压脉冲旁路二极管VD9不同接法对引弧、稳弧及设备安全的影响。     

邻—(4—乙基苯甲酰基)苯甲酸的研究

本文阐述了通过Friedel-Crafts反应合成邻-(4-乙基苯甲酰基)苯甲酸的方法.研究了影响产物质量的因素,提出了适宜的工艺条件.     

Trends and variations in neonatal length of in-hospital stay in Canada

The objectives of this study were to evaluate the possible mechanisms involved in prolongation of bleeding time in pre-eclamptic patients receiving a magnesium sulfate infusion to prevent convulsions. Eighteen pre-eclamptic patients near term or at term (4 cases 33 to 35 weeks; the remainder > 36 weeks) were studied. Fifteen of them received magnesium sulfate infusion; 3 did not and served as controls. Bleeding time (modified Ivy method with Surgicutt), platelet count, platelet aggregation pattern, as well as serum arachidonic acid metabolites [thromboxane B2 (TxB2) and 6-Keto-prostaglandin F1 alpha (6-Keto-PGF1 alpha)] werde done on admission to the labor floor (before magnesium infusion) and repeated at discontinuation of the infusion, 12-24 hours postpartum; the controls received the second test 24 hours postpartum. Thirteen of 15 patients receiving magnesium sulfate had an increase in bleeding time from an average of 6 minutes 31 seconds to 11 minutes 56 seconds, an 82% rise (p < 0.004). In 2 there was a decrease. Among the 3 controls the averages were 6 minutes 38 seconds and 6 minutes 3 seconds. The total magnesium given ranged from 52.5 to 145 grams. Platelet counts averaged 251,000/mm3 (range 145,000-519,000). Platelet aggregation pattern done in 11 patients and was normal and unchanged after magnesium in 10 of the patients with increased bleeding time and one control. TxB2 and 6-Keto-PGF1 alpha levels did not change significantly either after magnesium administration (688 and 135 pgm/ml, to 654 and 117) or in controls (695 and 230 pgm/ml, to 445 and 225). Likewise, the ratio of these 2 substances did not change in either group (6.3 to 6.6, and 4.2 to 2.2). There was no correlation between duration of infusion or total magnesium given and directions of small changes observed. This study confirms a prior preliminary observation that magnesium sulfate infusion, as currently used to prevent eclamptic convulsions, induces a significant prolongation of bleeding time. This effect is mediated neither by changes in platelets count or aggregation pattern, nor by changing the level or ratios of serum arachidonic acid metabolites (TxB2 and 6-Keto-PGF1 alpha). Further studies are needed to clarify the mechanism of this clinically important observation of increased bleeding following magnesium sulfate infusion.     

预处理工艺对硬质合金与金刚石膜间粘结力的影响

在两种经不同预处理的硬质合金YG8基底上，采用微波等离子体化学气相沉积法，在微波功率2kW，压强4.0kPa和6.5kPa，CH4和H2流量分别为1.6cm/s和100.0cm/s的条件下生长金刚石薄膜。利用X射线衍射检测了金刚石薄膜是否存在，用拉曼光谱分析了薄膜的质量，用金相显微镜观察了薄膜的洛氏硬度压痕，标定并比较了不同预处理工艺膜与基底的结合力。实验结果表明，不同的预处理方法对于粘结力的影响不大，最主要的因素是钴含量的多少。     

基于CDMA智能网平台的增值业务--"位置服务"

本主要介绍基于CDMA智能网平台的一种增值业务——“位置服务”，阐述这个业务的网络结构、涉及到的技术问题和解决方案，并将这个整体思路投入到开发业务中去。     

Control of free-radical emulsion polymerization of methyl methacrylate by oxygen injection. II. Experimental study

Oxygen injection has been proposed and experimentally demonstrated as an effective control measure for limiting the rate of heat release and altering the rate of polymerization in emulsion processes. A detailed mathematical model has been previously developed to describe the system behavior with and without oxygen injection. A simple lab scale apparatus was constructed and run extensively. Only trace quantities of oxygen are needed to inhibit the reaction completely. The facile response makes this method attractive for fast temperature control. However, because of the rapid penetration of dissolved oxygen into the polymer particles, growing radical chains are terminated prematurely, lowering product molecular weights. To minimize this detrimental effect, pulsed oxygen control is used and extensive experimental work was performed to determine the effects of controller set points on molecular weight. Moderate oxygen flows and moderate set point temperatures are found to give the optimal response without significant lowering of the final molecular weight. Injected quantities agree well with the order-of-magnitude sparging calculations needed to completely stop initiation. However, complete agreement between model simulations and experimental results was not reached due to an unmeasured loss of monomer from the reactor. Chain transfer to monomer is found to be important in modeling the polymer molecular weight. It has, however, a negligible effect on the reaction rate.     

地源热泵——辐射地板联供试验

通过地源热泵－辐射地板系统冬夏联供试验，讨论了该系统作为新型环保节能空调方式的可行性及优越性，并对运行中出现的问题进行分析。