动态评价技术在塔河碳酸盐岩缝洞型油气藏中的应用

塔河油田奥陶系油气藏是大型碳酸盐岩溶洞型油气藏，其储渗空间主要为大小不同的溶洞、裂缝带、溶蚀孔隙等组成，该油气藏具有极强的非均质性，单纯用静态资料来认识这类油气藏是非常困难。文章提出利用生产动态资料和信息进行该类型油气藏研究的新思路，利用人工神经网络技术在处理非线性相关参数预测方面的优势，并以渗流理论为基础，结合试井成果，选用已知油井的产量、油嘴、油压、含水率、气油比、原油密度等6个开发动态参数作为样品输入数据，推导出影响油气藏开发的重要参数（地层系数）与生产信息的关系，建立了人工神经网络预测储层参数的结构模型。通过塔里木盆地塔河油气田实例研究，说明了利用动态信息评价油气藏技术在碳酸盐岩缝洞型油气藏储层预测和非均质性分析等方面具有较高的实用价值。     

A high-performance multichannel dual-gate poly-Si TFT fabricated by excimer laser irradiation on a floating a-Si thin film

A new excimer laser annealing (ELA) process that uses a floating amorphous-Silicon (a-Si) thin film with a multichannel structure is proposed for high-performance poly-Si thin-film transistors (TFTs). The proposed ELA method produces two-dimensional (2-D) grain growth, which can result in a high-quality grain structure. The dual-gate structure was employed to eliminate the grain boundaries perpendicular to the current flow in the channel. A multichannel structure was adapted in order to arrange the grain boundary to be parallel to the current flow. The proposed poly-Si TFT exhibits high-performance electrical characteristics, which are a high mobility of 504 cm/sup 2//Vsec and a low subthreshold slope of 0.337 V/dec.     

Defocusing image to pattern contact holes using attenuated phase shift masks

The patterning of contact holes by selecting out-of-focus image plane (defocus) using attenuated phase shift masks (APSM) has been studied. Defocus is found to enhance the image modulation at low partial coherence for contact holes with negative local average of mask function. Semi-dense holes up to 130 nm in 8% APSM have been printed by 0.5 μm defocus at a partial coherence of 0.31 using KrF scanner with highest numerical aperture of 0.68. However, these holes were closed with in-focus imaging. Defocus is also found to be beneficial for patterning the pitches that have extensive side lobes with in-focus imaging.     

Joint scheduling and power control supporting multicasting in wireless ad hoc networks

This paper addresses the problem of power control in a multihop wireless network supporting multicast traffic. We face the problem of forwarding packet traffic to multicast group members while meeting constraints on the signal-to-interference-plus-noise ratio (SINR) at the intended receivers. First, we present a distributed algorithm which, given the set of multicast senders and their corresponding receivers, provides an optimal solution when it exists, which minimizes the total transmit power. When no optimal solution can be found for the given set of multicast senders and receivers, we introduce a distributed, joint scheduling and power control algorithm which eliminates the weak connections and tries to maximize the number of successful multicast transmissions. The algorithm allows the other senders to solve the power control problem and minimize the total transmit power. We show that our distributed algorithm converges to the optimal solution when it exists, and performs close to centralized, heuristic algorithms that have been proposed to address the joint scheduling and power control problem.     

Measurement and numerical simulation of three‐dimensional fiber orientation states in injection‐molded short‐fiber‐reinforced plastics

To determine three‐dimensional fiber orientation states in injection‐molded short‐fiber composites, a confocal laser scanning microscope (CLSM) is used. Since the CLSM optically sections the specimen, more than two images of the cross sections on and below the surface of the composite can be obtained. Three‐dimensional fiber orientation states can be determined by using geometric parameters of fiber images obtained from two parallel cross sections. For experiments, carbon‐fiber‐reinforced polystyrene is examined by the CLSM and geometric parameters of fibers on each cross‐sectional plane are measured by an image analysis. In order to describe fiber orientation states compactly, orientation tensors are determined at different positions of the prepared specimen. Three‐dimensional orientation states are obtained without any difficulty by determining the out‐of‐plane angles utilizing fiber images on two parallel planes acquired by the CLSM. Orientation states are different at different positions and show the shell–core structure along the thickness of the specimen. Fiber orientation tensors are predicted by a numerical analysis and the numerically predicted orientation states show good agreement with measured ones. However, some differences are found at the end of cavity. They may result from the fountain flow effects, which are not considered in the numerical analysis. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 500–509, 2003     

Recording of volume hologram using a beam pattern from taperedoptical fiber

A photorefractive volume hologram was recorded and probed using light diffracted from a tapered optical fiber as a reference beam. A single-mode fiber (SMF) was chemically etched and tapered to give a complicated beam pattern, and it is shown that the tapered optical fiber can be utilized to increase the storage density of the volume hologram. Spatial selectivity of the volume hologram with this method was increased by two times compared to the normal SMF referencing, which is due to the fact that the complicated beam pattern has little correlation with its shifted version     

降低丙烯酰胺晶体中水份的探讨

本文介绍了如何通过控制结晶时间和离心速率获得低水分的丙烯酰胺晶体，给出了最佳生产工艺条件。     

Synthesis of LiFePO4 with fine particle by co-precipitation method

LiFePO₄ is a potential candidate for the cathode material of the lithium secondary batteries. A co-precipitation method was adopted to prepare LiFePO₄ because it is simple and cheap. Nitrogen gas was needed to prevent oxidation of Fe²⁺ in the aqueous solution. The co-precipitated precursor shows the high reactivity with the reductive gas, and the single phase of LiFePO₄ is successfully synthesized with the aid of carbon under less reductive conditions. LiFePO₄ fine powder prepared by co-precipitation method shows high rate capability, impressive specific capacity and cycle property.