A cathode readout gas sampling calorimeter with conductive plastic tubes

We constructed and tested a prototype gas sampling electromagnetic calorimeter of the Pb-proportional tube sandwich type. The calorimeter uses conductive plastic tubes and cathode pad readout with a tower structure which resulted in reasonable energy and spatial resolutions for electrons in the momentum range 0.5–4.0 GeV/c; $\text{σ}{}_{\mathrm{E}}\text{E =}\text{21\%}\text{(E(}\text{GeV}\text{)}\text{)}{}^{\mathrm{<mtext>1</mtext><mtext>2</mtext>}}\text{, σ}{}_{\mathrm{x}}\text{= 6}\text{mm}\text{(at 3 GeV}$/c). This paper describes the test and the performance studied under various conditions.     

EXPANSION AND STRESS RELAXATION OF EXPRESSED CAKE

Expansion and stress relaxation of expressed cake are discussed.

The expansion process of expressed cake after release of load is very similar to consolidation of solidndashliquid mixtures, although a liquid flow in the expansion process is opposite in direction to that in consolidalion. This process can be analyzed well by use of the Terzaghi Voigt combined model. It is shown that the rate of primary deformation in expansion is much smaller than that in consolidation under the same change in compressive pressure. It is also found that the ratio of secondary deformation to total deformation in expansion is much larger than that in consolidation.

Stress relaxation of expressed cake, which is observed when expression is stopped before attaining an equilibrium compression state of a material, can be explained by use of a consolidation and expansion theory. In the relaxation process, local expansion appears near the drainage surface while local consolndash idation appears near the center of the cake. The equilibrium cake stress is uniquely determined by the average consolidation ratio when the expression is interrupted.     

Sensorless control of synchronous reluctance motors using on‐line parameter identification method not affected by position estimation accuracy

This paper presents a novel on‐line parameter identification method for sensorless control of Synchronous Reluctance Motors (SynRMs). Although conventional sensorless control methods based on mathematical models usually need some complex measurements of motor parameters in advance, the proposed identification method does not require them and can be realized on‐line. The proposed method identifies motor parameters under sensorless control, so rotor position and velocity cannot be used to identify these parameters. However, the proposed method does not need rotor position and velocity, and identified parameters are not affected by these estimation errors. The sensorless control using identified motor parameters is realized, and the effectiveness of the proposed method is verified by experimental results. © 2006 Wiley Periodicals, Inc. Electr Eng Jpn, 155(3): 62–69, 2006; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20258     

Immunohistochemical study of epithelioid hemangioendothelioma in the leg: a case report

Epithelioid hemangioendothelioma is a relatively rare lesion. Although its histogenesis has been well described, its immunohistochemical characteristics remain controversial. A case of epithelioid hemangioendothelioma of the soft tissue of the right leg in a 67-year-old Chinese woman is reported. Histologic findings of intracytoplasmic lumina in the tumor cells and positive immunostaining for vimentin, factor VIII-related antigen. CD34 and Ulex europaeus agglutinin 1 (UEA-1) were obtained, demonstrating differentiation of the tumor cells to endothelial cells, although staining for antibodies to cytokeratins AE1/AE3 and CAM5.2 was weak. CD34 as well as Factor VIII-related antigen is a useful marker of endothelial differentiation in this tumor. A review of the literature is also presented.     

A far-infrared spectroscopic study of low temperature soft phonon mode in Tris-Sarcosine Calcium Chloride(TSCC)

Temperature dependences of the soft phonon frequency and the damping constant in Tris-Sarcosine Calcium Chloride (TSCC) single crystal have been investigated between 5K and 100K by using a Fourier-transform far-infrared spectrometer. It has been observed that the soft phonon frequency decreases gradually and the damping constant increases as the transition temperature is approached from below The damping constant varies from 7cm^-1 a 90K to less than 0.5cm^-1 at 5K. It has been found that the damping constant is approximately proportional to temperature below about 60K.     

A simplified cascade current‐source inverter interconnected to a single‐phase three‐wire distribution system and its application to electric energy storage systems with batteries

A novel current source inverter system interconnected to the single‐phase grid is proposed. It has the same construction as the conventional three‐phase current source inverter that is interconnected to the single‐phase three‐wire distribution system. Though the proposed circuit has no output transformer, it can be equivalently performed as the single‐phase double cascade inverter by diverting the pole transformer in the utility system. By controlling the appropriate scheme, the output currents can be obtained as the five‐level waveforms and their distortions can be decreased sufficiently. It is applied to the interactive electric energy storage system with batteries and the basic discharging characteristics are discussed experimentally. © 2004 Wiley Periodicals, Inc. Electr Eng Jpn, 150(2): 50–61, 2005; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.10380     

Time-series primitive static states for detailing work state and flow of human-operated work machine

This paper proposes a quantification method for a comprehensive work flow in construction work for describing work states in more detail on the basis of analyzing state transitions of primitive static states (PSS), which consist of 16 symbolic work states defined by using on-off state of the lever operations and joint loads for the manipulator and end-effector. On the basis of the state transition rules derived from a transition-condition analysis, practical state transitions (PST), which are common and frequent transitions in arbitrary construction work, are defined. PST can be classified into essential state transition (EST) or nonessential state transitions (NST). EST extracts common phases of work progress and estimates positional relations between a manipulator and an object. NST reveals wasted movements that degrade the efficiency and quality of work. To evaluate comprehensive work flows modeled by combining EST and NST, work-analysis experiments using our instrumented setup were conducted. Results indicate that all the PSS definitely changes on the basis of PST under various work conditions, and work analysis using EST and NST easily reveals work characteristics and untrained tasks related to wasted movements.