Structural properties of phosphorous-doped polycrystalline silicon

The structural properties and hydrogen bonding of undoped and phosphorous doped polycrystalline silicon produced by step-by-step laser dehydrogenation and crystallization technique were investigated using Raman spectroscopy and hydrogen effusion measurements. At low laser fluences, E_L, a two-layer system is created. This is accompanied by the change in hydrogen bonding. The intensity of the Si–H vibration mode at 2000 decreases faster than the one at 2100 cm⁻¹. This is even more pronounced in phosphorous-doped specimens. The laser crystallization results in an increase of the hydrogen binding energy by approximately 0.2–0.3 eV compared to the amorphous starting materials.     

A generalized equation for the prediction of melting temperatures of homopolymers and copolymers

A generalized equation was derived to calculate the melting temperatures of homopolymers and copolymers. The Gibbs‐Thomson equation for homopolymers and a modified application to copolymers were derived using the proposed equation. The melting temperature T_m⁰ in the Flory equation corresponds to the melting temperature T_m^C,∞ of copolymer crystals with stems of infinite length. Also, T_m^C,n*, the melting temperature for copolymer crystals with stems containing the maximum possible number of structural units, n*, should be used instead of T_m⁰ as the basis of supercooling in crystallization. The proposed equation shows good agreement with experimental data for α‐alkene‐ethylene homogeneous copolymers.     

A knowledge-based system for sensor selection

This paper presents a Knowledge-based system (KBS) developed to allow users, who may not be knowledgeable about sensors, to select sensors suitable for their specific needs. The KBS runs on a micro-computer. The selection criteria are user specified and are based on the desired measurement parameters. The system output includes all of the operational and dimensional parameters of the recommended sensor, price, and vendor information.     

Terson''s syndrome in a patient with acute promyelocytic leukemia on all-trans retinoic acid treatment

Hypothermia induced by surface cooling has shown to protect vulnerable regions of the brain during an ischemic insult. This study evaluated the neuroprotective efficacy of neurotensin, a potent hypothermic agent, using a 5-min carotid occlusion procedure in the gerbil. In Experiment 1, the dose-response and time course of neurotensin-induced hypothermia were evaluated (n = 5/dose). Central infusion of 10, 20, and 30 micrograms neurotensin were found to significantly decrease core body temperature of conscious gerbils within 30 min of administration. In Experiment 2, gerbils pretreated with 30 micrograms neurotensin were permitted to become hypothermic or were maintained at 37 degrees-38 degrees C (rectal) during ischemic insult. Other gerbils were pretreated with peptide vehicle prior to ischemic insult (at 37 degrees -38 degrees C) or underwent a sham procedure (n = 6/condition). At 24 h after surgery, gerbils were tested for increased locomotor activity in an open-field apparatus. Gerbils pretreated with peptide vehicle or neurotensin and maintained at 37 degrees-38 degrees C during ischemia had significantly higher activity levels compared to the other treated groups. In contrast, gerbils made hypothermic with neurotensin exhibited activity levels similar to sham gerbils. Histological assessment revealed that neurotensin-induced hypothermia protected the CA1 region from ischemic damage.     

Breakdown probabilities for thin heterostructure avalanche photodiodes

The recurrence theory for the breakdown probability in avalanche photodiodes (APDs) is generalized to heterostructure APDs that may have multiple multiplication layers. The generalization addresses layer-boundary effects such as the initial energy of injected carriers as well as the layer-dependent profile of the dead space in the multiplication region. Reducing the width of the multiplication layer serves to both downshift and sharpen the breakdown probability curve as a function of the applied reverse-bias voltage. In structures where the injected carriers have an initial energy that is comparable to the ionization threshold energy, the transition from linear mode to Geiger-mode is more abrupt than in structures in which such initial energy is negligible. The theory is applied to two recently fabricated Al/sub 0.6/Ga/sub 0.4/As-GaAs heterostructure APDs and to other homostructure thin GaAs APDs and the predictions of the breakdown-voltage thresholds are verified.     

Effect of electricity tariff on the optimum insulation-thickness in building walls as determined by a dynamic heat-transfer model

Thermal insulation is one of the most effective energy-conservation measures in buildings. Despite the widespread use of insulation materials in recent years, little is known regarding their optimum thickness under dynamic thermal conditions. Insulated concrete blocks are among the units most commonly used in the construction of building walls in Saudi Arabia. Typically, the insulation layer thickness is fixed at a value in the range 2.5–7.5 cm, regardless of the climatic conditions, type and cost of insulation material, and other economic parameters. In the present study, a numerical model based on a finite-volume, time-dependent implicit procedure, which has been previously validated, is used to compute the yearly cooling and heating transmission loads under steady periodic conditions through a typical building wall, for different insulation thicknesses. The transmission loads, calculated by using the climatic conditions of Riyadh for a west-facing wall, are fed into an economic model in order to determine the optimum thickness of insulation (L_opt). The latter corresponds to the minimum total cost, which includes the cost of insulation material and its installation plus the present value of energy consumption cost over the lifetime of the building. The optimum insulation thickness depends on the electricity tariff as well as the cost of insulation material, lifetime of the building, inflation and discount rates, and coefficient of performance of the air-conditioning equipment. In the present study, the effect of electricity tariff on the computed optimum insulation thickness is investigated. Different average electricity tariffs are considered; namely, 0.05, 0.1, 0.2, 0.3 and 0.4 SR/kWh (designated as Cases 1–5, respectively; 1 US$ = 3.75 Saudi Riyals). Results using moulded polystyrene as an insulating material show that the values of L_opt are: 4.8, 7.2, 10.9, 13.7 and 16.0 cm for Cases 1–5. Under the conditions of optimal insulation thickness for each electricity tariff, Case 1 gives the lowest total cost of 17.4 SR/m², while Case 5 gives the highest total cost of 53.1 SR/m². Corresponding thermal performance characteristics in terms of yearly total and peak transmission loads, R-value, time lag and decrement factor are presented.     

Impacts of varnishes and impregnation chemicals on combustion properties of oak (Quercus petreae lipsky)

This study was performed to determine the effects of varnishing after impregnation with boron compounds on combustion properties of oak. For this aim, the test samples prepared from oak (Quercus petreae Liebl.) wood were impregnated according to ASTM D 1413‐99 with boric acid (Ba) and borax (Bx) by vacuum technique. After impregnation, surfaces were coated by cellulosic (Cv), synthetic (Sn), polyurethane (Pu), waterborne (Wb), acrylic (Ac), and acid hardening (Ah) varnishes in accordance to ASTM D 3023. Combustion properties of samples after varnishing process were determined, according to ASTM E 160‐50. According to material and process types, combustion temperature was the highest in Bx and Cv, the lowest in Ba and Ac. An important difference was not observed between without flame source combustion (WFSC) and flame source combustion (FSC). According to combustion type, impregnation material and varnish type, combustion temperature was the highest value in WFSC + Bx + acid hardening varnish combination and the lowest in WFSC + Ba + acrylic varnish combination. As a result, the tested varnishes showed an increasing impact but boron compounds showed a decreasing impact on combustion properties of oak. In consequence, for usage areas having a high risk of fire, impregnation of wood material with boron compounds before varnishing will decrease combustion temperature and provide security. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2008     

Structures in superconducting YBa2Cu3O7−δ thin films investigated by magneto-optic technique

Using a reflection magneto-optic technique we have investigated natural inhomogeneities and artificial structures in YBCO thin films exposed to an external magnetic field. The artificial structures were mechanically scratched by scanning a diamond tip with different loading over the film surface. Alternatively planar structures with reduced oxygen content could be patterned by heating the YBCO film with a focused laser beam in nitrogen atmosphere. Depending on the laser annealing parameters different screening properties concerning the applied magnetic field could be achieved.As a magneto-optically active layer we used EuS films evaporated on glass as well as bismuth- and gallium-doped lutetium-iron-garnet films grown onto (111) oriented gadolinium-gal lium-gar net substrates by liquid phase epitaxy. In contrast to measurements with EuS films that show only weak faraday rotation for temperatures higher than 20 K the magneto-optic studies have been expanded to about 60 K by using the garnet films.     

Time jitter analysis of 1-bit sigma-delta synthesizer

This letter presents a general analysis of time jitter in sigma-delta synthesizer. One of the practical applications of 1-bit sigma-delta systems is a generation of high-resolution local oscillator (LO) signals. In order to generate LO signals, one may use a single-bit sigma-delta technique to encode sine waves. Today, direct generation of high-frequency sine wave using a clock with higher frequency, is possible. In this letter, we will analyze different LO signal generators and develop a practical way of computation to decide how to choose the best configuration under minimum degradation of signal-to-noise ratio (SNR) at the output.