Vorticity field structure associated with the 3D Tollmien-Schlichting waves

Details of the vorticity field structure associated with the 3D Tollmien-Schlichting waves have been examined based upon the recent numerical studies of the subject. First, a single obliquet-s wave has been found to have the velocity component parallel to the wave front playing an overall dominant role, in particular, to create the longitudinal vorticity. The so-called Benney-Lin longitudinal vortices are then demonstrated to be, in fact, a minor consequence compared with the localized longitudinal vorticity field and its periodic pumping. Finally, the formation of the longitudinal vorticity field in the fundamental- and subharmonic-mode interactions is explained. The research reported in this paper has been supported in part by Bundesministerium für Forschung und Technologie and by Deutsche Forschungsgemeinschaft. The major part of the paper has been presented at the Third Asian Congress of Fluid Mechanics, 1–5 September 1986, in Tokyo, as a General Lecture by the senior author, FRH.     

Towards inverse modeling of turbidity currents: The inverse lock-exchange problem

A new approach is introduced for turbidite modeling, leveraging the potential of computational fluid dynamics methods to simulate the flow processes that led to turbidite formation. The practical use of numerical flow simulation for the purpose of turbidite modeling so far is hindered by the need to specify parameters and initial flow conditions that are a priori unknown. The present study proposes a method to determine optimal simulation parameters via an automated optimization process. An iterative procedure matches deposit predictions from successive flow simulations against available localized reference data, as in practice may be obtained from well logs, and aims at convergence towards the best-fit scenario. The final result is a prediction of the entire deposit thickness and local grain size distribution. The optimization strategy is based on a derivative-free, surrogate-based technique. Direct numerical simulations are performed to compute the flow dynamics. A proof of concept is successfully conducted for the simple test case of a two-dimensional lock-exchange turbidity current. The optimization approach is demonstrated to accurately retrieve the initial conditions used in a reference calculation.     

Kilopixel X-ray Microcalorimeter Arrays for Astrophysics: Device Performance and Uniformity

We are developing kilopixel arrays of TES microcalorimeters to enable high-resolution x-ray imaging spectrometers for future x-ray observatories and laboratory astrophysics experiments. Our current array design was targeted as a prototype for the X-ray Microcalorimeter Spectrometer proposed for the International X-ray Observatory, which calls for a 40×40-pixel core array of 300?μm devices with 2.5?eV energy resolution (at 6?keV). Here we present device characterization of our 32×32 arrays, including x-ray spectral performance of individual pixels within the array. We present our results in light of the understanding that our Mo/Au TESs act as weak superconducting links, causing the TES critical current (I _c ) and transition shape to oscillate with applied magnetic field (B). We show I _c (B) measurements and discuss the uniformity of these measurements across the array, as well as implications regarding the uniformity of device noise and response. In addition, we are working to reduce pixel-to-pixel electrical and thermal crosstalk; we present recent test results from an array that has microstrip wiring and an angle-evaporated copper backside heatsinking layer, which provides copper coverage on the four sidewalls of the silicon wells beneath each pixel.     

Implications of Weak Link Effects on Thermal Characteristics of Transition-Edge Sensors

Weak link behavior in transition-edge sensor (TES) microcalorimeters creates the need for a more careful characterization of a device’s thermal characteristics through its transition. This is particularly true for small TESs where a small change in the bias current results in large changes in effective transition temperature. To correctly interpret measurements, especially complex impedance, it is crucial to know the temperature-dependent thermal conductance, G(T), and heat capacity, C(T), at each point through the transition. We present data illustrating these effects and discuss how we overcome the challenges that are present in accurately determining G and T from I–V curves. We also show how these weak link effects vary with TES size. Additionally, we use this improved understanding of G(T) to determine that, for these TES microcalorimeters, Kaptiza boundary resistance dominates the G of devices with absorbers while the electron-phonon coupling also needs to be considered when determining G for devices without absorbers     

Austenitic stainless steel for separating safeguards: development of an FEA-model for the simulation of impact tests in reference to material specific parameters

Austenitic stainless steels have a high potential for the use in separating safeguards of machine tools based on the TRIP (Transformation Induced Plasticity) effect. The problem with these materials is the high variance of the alloy composition. Therefore, the specific penetration resistance W _D,spec varies significantly. The presented research analyses the impact of material specific parameters on the specific penetration resistance W _D,spec and the FEA simulation of impact tests. The result of the project is the knowledge of the penetration resistance and hence the security (factor of safety) against penetration.     

Mechanisms for the formation of low temperature,non-alloyed Au-Ge ohmic contacts to n-GaAs

Low temperature, non-alloyed Au-Ge contact formation ton-GaAs is a multi-step pro-cess. During the first 5 min of annealing at 320° C the Au and Ge segregate into regions a few microns in size and extend over the entire thickness of the metal layer and sig-nificant in-diffusion of the Au and Ge and out-diffusion of the Ga and As occurs. This intermixing reduces the barrier height from 0.75 to 0.40 eV. The contact does not show ohmic behavior until it has been annealed for 3 hr. During this time Ge continues to in-diffuse but at a slower rate than it did initially. The rate of Ge in-diffusion is en-hanced by the presence of Au since samples containing less Au require longer anneals to show ohmic behavior and have higher specific contact resistances. The presence of excess As, which is prevented from evaporating by a Si₃N₄ cap has the opposite effect since capped layers have higher specific contact resistances. Au-Ge phases appear after approximately 3 hr of annealing, therefore, Au-Ge phases cannot be responsible for the reduction in barrier height. The interface morphology is smooth, differing from that of pure Au and alloyed contacts that often contain spiking of the metals into the semi-conductor. The orientation relationship for the Au grains differs from that of pure Au. Work performedat U.S. Army ETDL, Fort Monmouth, NJ 07703. Work performed at U.S.Army ETDL, Fort Monmouth, NJ 07703.     

Mehr leichte Produkte aus Rohölen – Eine Herausforderung für die Ölindustrie

More light products from crude oil – A challenge to the oil industry . A new long-term pattern of demand for oil is evolving mainly due to the politically limited availability of crude oil and increasing prices. For the Federal Republic of Germany an essentially constant level of demand for naphtha and gasoline is expected with a shrinking demand for distillate and fuel oil. The expected pattern cannot be met by the currently predominating hydroskimming process. Technological possibilities and development of conversion processes are emphasized in this article: Thermal catalytic and hydrocracking as well as hydroconverting for steam cracker feed generation. Increasing importance is predicted for residue cracking. Oil will continue to make a major contribution and the oil industry will be able to keep step with product demand.     

增强现实技术于洪水风险沟通中的应用

气候变迁,特别是洪水问题给地处三角洲的城市带来了与日俱增的风险。作为应对手段,提出一种整合性的洪水风险管理方法,该方法确保了洪水风险沟通在洪水风险管理战略中的重要地位。洪水的可视化作为洪水风险沟通的一种工具,在改变人们对洪水风险的观念方面有着强大的作用。它可以通过互动的方式,使当地的利益相关者了解洪水的剩余风险和未来风险。其中增强现实技术作为一种可视化手段,它的快速发展与应用为风景园林设计、规划与教育等领域提供了崭新的交互方式。首先,探讨增强现实技术(AR)在洪水风险沟通中的应用现状,并重点关注增强现实技术的2个关键应用领域:对现场决策的支持和针对高层次设计的可视化与对景观干预的评估。随后,展示一种基于增强现实技术所开发的应用,该款创新性的应用为洪水风险沟通提供了一种轻量化的可视化手段。     

Gyroscopic and mode interaction effects on micro-end mill dynamics and chatter stability

This paper investigates the gyroscopic and mode interaction effects on the micro-end mill dynamics and the stability behavior due to regenerative chatter. A high-speed spindle system for micro-milling is modeled using finite elements. The transfer functions and the mode shapes are studied to gain a deep insight into the dynamic characteristics. The experimentally identified chatter states and operational vibration modes are given to verify the analytical results. It is shown that, due to the small rotary inertia of the micro-end mill, the gyroscopic effect considered in the inertial frame is less significant despite high rotational speeds. The mode interaction strongly affects the dynamics and the chatter stability. Moreover, piezoelectric elements are applied to in-process excitation in order to identify the transfer behavior of the micro-end mill in the operating state.     

Learners' questions and comprehension in a tutoring setting.

Three experiments, presented within the framework of Activity Theory, deal with the relationship between adult learners' questions and subsequent comprehension in a tutorial learning setting. Students were first given verbal instructions (acquisition) to a novel card game and then asked to play one hand with the teacher (implementation). In Experiment 1, there was no correlation between number of questions asked during acquisition and comprehension, but questions during implementation were negatively correlated with comprehension. In Experiment 2, learners whose questions were answered during acquisition scored higher than those whose questions were not answered. In Experiment 3, learners whose questions were answered during implementation showed greater gains in comprehension than those whose questions were answered during acquisition. Individual differences in question-asking during implementation but not acquisition were significantly related to comprehension. The results confirm the view that questions answered during knowledge implementation more effectively aid comprehension than those answered during acquisition. (PsycINFO Database Record (c) 2010 APA, all rights reserved)