Operation of superconducting fault current limiter using vacuum interrupter driven by electromagnetic repulsion force for commutating switch

Using conventional high‐temperature superconducting wire, a model superconducting fault current limiter (SFCL) is made and tested. Solenoid coil using Bi2223 silver sheath wire is so made that inductance is as small as possible and a vacuum interrupter is connected in series to it. A conventional reactor coil is connected in parallel. When the fault current flows in this equipment, superconducting wire is quenched and current is transferred into the parallel coil because of voltage drop of superconducting wire. This large current in parallel coil actuates magnetic repulsion mechanism of vacuum interrupter. Due to opening of vacuum interrupter, the current in superconducting wire is broken. By using this equipment, current flow time in superconducting wire can be easily minimized. On the other hand, the fault current is also easily limited by large reactance of parallel coil. © 2008 Wiley Periodicals, Inc. Electr Eng Jpn, 164(1): 52–61, 2008; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20315     

Thermal stability of reinforced Nb3Sn composite superconductor under cryocooled conditions

Several types of reinforced Nb₃Sn wires have been developed to prevent reduction of superconducting properties by applying a strong electromagnetic force. To fabricate a cryocooled magnet using those reinforced wires, we experimentally measured the minimum quench energy (MQE) under cryocooled conditions of some reinforced Nb₃Sn wires. As a result, it became clear that thermal stability expressed as MQE was controlled by the temperature margin between the temperature of the operating condition and the transition temperature from superconductivity to normal. Using the FEM analysis, it was realized that the cause of the decline in thermal stability for the reinforced wires was the low thermal conductivity of the reinforced materials.     

Effect of ibudilast on microcirculation thrombosis in rat inner ear

Arterial wall thickening may be quantitatively assessed by measuring the intima-media thickness (IMT) with high resolution ultrasound. Previous studies have shown a good inter/intraobserver variability of IMT measurements in the common carotid. In this study we evaluated the inter/intraobserver variability of IMT measurements in 10 randomly selected asymptomatic subjects (age 55.4 +/- 6). Two carotids and two femorals were studied in each subject. IMT for each patient was the average of five IMT measurements at the artery bifurcation. Three observers repeated the scanning and the measurements twice with no knowledge of the previous readings. The between observer coefficient of variation (CV) was 8.45%; the intraobserver CV (mean of carotids and femorals) varied from 4.4 to 5.1% for the three observers who measured IMT three times. The mean absolute difference between the first and the third measurement was 0.0738 mm. In conclusion IMT measurement variability is mostly due to differences between observers. The intraobserver variability is very small. IMT measurements at the carotid and femoral bifurcations have a low variability and are a good expression of atherosclerosis as they consider early lesions at the bifurcation level which may not be observed in the common carotid.     

Design optimization of tall tubular lead/acid cells based on an analysis of the reaction distribution

In order to estimate the discharge performance of tall lead/acid cells (with tubular positives), changes in current and potential distributions with discharge progress were calculated with a computer on the basis of plate resistance and the current—potential—time relationship between small facing parts of positive and negative plates. The taller the cell, the larger the voltage drop along the plates. Thus, the discharge time became shorter despite a large amount of available active mass remaining in the bottom part of the plates.Various current-collector designs were evaluated, e.g., one with varying resistance at each height; a side conductor placed along the plates and connected to them at the top, centre and bottom, etc. Results revealed an optimum collector design with which the maximum discharge capacity could be obtained. Furthermore, it was shown that the side conductor markedly improved the discharge performance because the active mass near the connecting parts was appreciably used.     

IMPINGING JET DRYER

In coating and gravure printing, an impinging jet nozzle with high thermal efficiency for drying of coated film was developed.

Trial production 0f 40 kinds of nozzle enables to develop a high-performance impinging jet nozzle with heat transfer coefficient 1.5 times larger than that of current slit nozzle, through measurement of heat transfer coefficient, visualizations of air flow and heat transfer, and measuremenu of jet velocity and turbulence distribution. The purpose of the trial production was to expand a range of high heat transfer and promote turbulence compared with the current nozzle.

Paying attention to mass transfer within gravure ink coated film, drying characteristic of the film was analyzed by numerical solution of a set of equations governing the drying process in which concentration dependencies 0f the diffusion coefficient and the equilibrium vapor pressure were considered.

Applying these analyses. an industrial scale dryer with excellent drying efficiency has finally been developed.     

A new voltage control equipment using fuzzy inference

Power system control equipment needs higher sensitivity and operational reliability. Advanced voltage control equipment is needed for reducing the frequency of tap changes and improving the characteristics (the relationship between the actual voltage and reference voltage) of the voltage to meet today's power system requirements. However, these objectives are in a trade-off relationship. Studies of voltage control derived from a knowledge base suitable for electric power systems can satisfy these objectives using fuzzy inference. Compared with corresponding conventional equipment, the new equipment improved the deviation of 30 min average voltage of 30 percent. This paper describes the design concept of new voltage control equipment using fuzzy inference. In addition, field test results are described along with rules of fuzzy inference, membership functions, and the deviation of 30 min average voltage through detailed simulation.     

Discharge behaviour of electrodeposited PbO2 and Pb electrodes

The discharge behaviour of electrodeposited lead dioxide and lead electrodes was investigated under various conditions; the surfaces of the discharged electrodes were observed with a scanning electron microscope. Both the positive and negative electrodes were passivated by a covering of deposited lead sulphate crystals. The amount of lead sulphate required for passivation depended on the size of the crystals.     

Handling of fine-particles by time-averaged particle driving method in plasmas

We developed a noble technique for the fine-particle handling in plasmas. In this method a pair of point electrodes are introduced in the plasma, to which positive pulses are applied alternatively. When the pulse repetition period is shorter than the particle response time, the particles feel only time-averaged force because of their large mass. Spatial profile of the equivalent potential of the time-averaged force varies from a circle to an ellipse with an increase in the local discharge at the electrodes. The particles are eventually transported toward a middle point between two point-electrodes, being almost independent of their initial positions. This method is quite effective for converging fine particles in the plasma.     

Development of an anisotropic conductive adhesive film (ACAF) from epoxy resins

A thermoset type anisotropic conductive adhesive film (ACAF), which electrically connects an ITO glass and a flex circuit both having conducting pattersn of less than 100 μm in pitch, has been developed. In this development, bisphenol A and bisphenol F epoxy resins were tested to formulate an ACAF with easy-to-handle tackiness, flexibility, and strenght. A curing agent that gives fast cure and long shelf-life properties to the epoxy resin was also selected. The tensile stress–strain responses of obtained adhesive films were successfully used for determining the formulation. Good aftercure physical properties (electrical and mechanical) were obtained. Durability against high temperature and high humidity were also tested to confirm long-term stability of the conduction of this ACAF. © 1995 John Wiley & Sons, Inc.