Wear and Creep Characteristics of a Carbon‐Derived Si3N4/SiC Micro/Nanocomposite

In the presented work some properties of a recently developed Si₃N₄/SiC micro/nanocomposite have been investigated. The material was tested using a pin on disc configuration. Under unlubricated sliding conditions using Si₃N₄ pin at 50 % humidity, the friction coefficient was in the range of 0,6 ‐ 0,7. The reduction of humidity resulted in a lower coefficient of friction, in vacuum the coefficient of friction had a value of about 0,6. The wear resistance in vacuum was significantly lower then that in air. The wear patterns on the Si₃N₄+SiC disc revealed that mechanical fracture was the wear controlling mechanism. Creep tests were realized in four point bending configuration in the temperature interval 1200‐1400 °C at stresses 50,100 and 150 MPa and the minimal creep deformation rate was established for each stress level. The activation energy, established from the minimal creep deformation had a value of about 360 kJ/mol and the stress exponent values were in the range of 0.8‐1.28. From the achieved stress exponents it can be assumed that under the studied load/temperature conditions the diffusion creep was the most probable creep controlling mechanism.     

Magnetic field dependence of shielding current density in Y-Ba-Cu-O rings at 77 K

A method for contactless measurement of the shielding critical current density and its dependence on the external magnetic field is described and analyzed. The obtained values are compared with those measured resistively on two different samples. It is shown that the shielding critical current densityJ _cs and the intergranular transport current densityJ _cr are identical if the measurement conditions are similar. A degradation ofJ _cs measured in the external field with AC ripple has been observed.     

CFD Prediction of Flow and Homogenization in a Stirred Vessel: Part I Vessel with One and Two Impellers

A simulation of flow field and tracer homogenization was performed using the commercial CFD software FLUENT 6.1. The aim is to investigate the potential of CFD software to predict concentration distribution of added tracer in cylindrical vessels. The calculated results – dimensionless velocity profiles, power and pumping numbers, dimensionless concentration curves, and mixing times – were compared with experiments in stirred vessels. In Part I, the study was performed for vessels agitated by one or two impellers on a centric shaft. Two different impellers were used – a 6‐bladed 45° pitched blade turbine and a standard Rushton turbine. The standard k‐? turbulence model and multiple reference frames method were used for the simulations. The influence of the grid type was also investigated; three types of grid – a structured, unstructured and a special user‐defined grid – were studied.     

3D Hair sketching for real-time dynamic & key frame animations

Physically based simulation of human hair is a well studied and well known problem. But the “pure” physically based representation of hair (and other animation elements) is not the only concern of the animators, who want to “control” the creation and animation phases of the content. This paper describes a sketch-based tool, with which a user can both create hair models with different styling parameters and produce animations of these created hair models using physically and key frame-based techniques. The model creation and animation production tasks are all performed with direct manipulation techniques in real-time.     

Nonuniformity of phase structure in immiscible polymer blends

This article is focused on the phase structure development in immiscible polymer blends during melt mixing. Nonuniformity of the phase structure, i.e., the coexistence of areas containing particles with markedly different size distribution, was detected in quenched and compression molded samples of a number of various blends prepared by long and intensive mixing in the chamber of a Plasticorder. The same effect was found also for polystyrene/polyamide blends prepared in a twin‐screw extruder. It was shown that neglecting nonuniformity of the phase structure can lead to considerable error in evaluation of the effect of system parameters on the blend morphology. The reasons for the effect were discussed and it was found that inhomogeneous flow field in mixers is a plausible explanation of the nonuniform phase structure. POLYM. ENG. SCI., 2008. © 2008 Society of Plastics Engineers     

A Study on NMR and GC/MS Spectra of the Isomers of Linear Hexyl Naphthalene

The GC/MS and NMR analysis of the reaction products of naphthalene with 1-bromohexane were reported. The products obtained were suggested to have six isomers of linear hexylnaphthalene and the structure of each isomer was determined by GC/MS and NMR spectra. For the first time, the unique chemical shift data were obtained. The content of each isomer calculated by ¹H NMR and ¹³C NMR spectra was consistent with that by GC/MS spectra, which confirmed the accuracy of NMR data.     

Thomas Fincke und die <Emphasis Type="Italic">Geometria rotundi</Emphasis>

Thomas Fincke (January 6^th, 1561–April 24^th, 1656), born in Flensburg (Germany), was one of the very most important and significant scientists in Denmark during the seventeenth century, a mathematician and astrologer and physician in the beginning of modern science, a representative of humanism and an influentual academic organizer. He studied in Strasbourg (since 1577) and Padua (since 1583) and received his M.D. in Basel (1587), he practised as a physician throughout his life (since 1587 or 1590) and became a professor at Copenhagen (1591). But he was best known because of his Geometriae rotundi libri XIIII (1583), a famous book on plane and spherical trigonometry, based not on Euclid but on Petrus Ramus. In this influentual work, in which Fincke introduced the terms tangent and secant and probable first noticed the Law of Tangents and the so-called Newton-Oppel-Mauduit-Simpson-Mollweide-Gauss-formula, he showed himself to be „abreast of the mathematics of his time“.