Simulation of deep space network traffic under various loading conditions

This is a follow‐up report on the end‐to‐end data link performance of the NASA deep space network. The focus of this report is the effect of traffic loading on data delivery. Architecture of the existing network is modeled via COMNET. The contribution of the data latency to the overall acquisition time is simulated as a function of network traffic conditions. The results show steady‐state latencies in the range of tenths of milli‐seconds under a mild loading condition. During heavy traffic, a delay rate of over a hundred seconds of increased delay per hour of network operation time is observed. This is primarily due to the queueing delays associated with large volume of data stored in the buffers throughout the link. This revised version was published online in June 2006 with corrections to the Cover Date.     

Nasopharyngeal colonization in Costa Rican children during the first year of life

BACKGROUND: The establishment of the nasopharyngeal flora was followed in Costa Rican children from birth to 1 year of age. METHODS: Nasopharyngeal cultures were obtained at 1 (n = 413), 3 (n = 393), 6 (n = 376) and 12 months (n = 356) of age from children representative of the population in the Puriscal district. Weekly cultures were obtained from a subcohort of these children (n = 101). Mother-infant diads (n = 95) and preschool children (n = 208) attending day-care centers were also studied. RESULTS: The estimated proportion of colonized children in the population differed markedly depending on the frequency of culture. Quarterly cultures showed a slow increase in carrier rates from 3.9% for Haemophilus influenzae, 3.1% for Streptococcus pneumoniae and 6.5% for Moraxella catarrhalis at 1 month of age to 10.1% carrying H. influenzae and 19.4% carrying S. pneumoniae by the end of the first year. By quarterly culture the proportion of children colonized at least once was 36% for S. pneumoniae, 26% for H. influenzae and 28% for M. catarrhalis. In contrast weekly sampling showed that 95 to 100% of the children were colonized at least once during the first year of life with H. influenzae, S. pneumoniae or M. catarrhalis. Nasopharyngeal carriage of H. influenzae, S. pneumoniae and M. catarrhalis was low in the mothers, and very few mother-infant pairs carried identical bacteria at the same time. In contrast carrier rates were high in the siblings attending day care (H. influenzae 27.9%, S. pneumoniae 39.4%, both organisms 26.6%). Infants with siblings had significantly higher bacterial carriage at all ages than infants without siblings. CONCLUSIONS: Quarterly nasopharyngeal cultures showed that Costa Rican infants acquire their nasopharyngeal flora at a rate comparable with that for infants in developed countries and that siblings are an important source of the bacteria. Weekly samplings showed that virtually all children were colonized at least once during the first year of life.     

A new monitoring system for piping systems in fossil fired power plants

A CEC-funded project has been performed to tackle the problem of producing an advanced Life Monitoring System (LMS) which would calculate the creep and fatigue damage experienced by high temperature pipework components. Four areas were identified where existing Life Monitoring System technology could be improved:

1. 1. the inclusion of creep relaxation

2. 2. the inclusion of external loads on components

3. 3. a more accurate method of calculating thermal stresses due to temperature transients

4. 4. the inclusion of high cycle fatigue terms.

The creep relaxation problem was solved using stress reduction factors in an analytical in-elastic stress calculation. The stress reduction factors were produced for a number of common geometries and materials by means of non-linear finite element analysis. External loads were catered for by producing influence coefficients from in-elastic analysis of the particular piping system and using them to calculate bending moments at critical positions on the pipework from load and displacement measurements made at the convenient points at the pipework. The thermal stress problem was solved by producing a completely new solution based on Green's Function and Fast Fourier transforms. This allowed the thermal stress in a complex component to be calculated from simple non-intrusive thermocouple measurements made on the outside of the component. The high-cycle fatigue problem was dealt with precalculating the fatigue damage associated with standard transients and adding this damage to cumulative total when a transient occurred.

The site testing provided good practical experience and showed up problems which would not otherwise have been detected.     

Expectations about counseling in Yucatán, Mexico: Toward a "Mexican psychology."

Conducted a study of client expectations of psychological services in Yucatán, Mexico, under the sponsorship of a grant from the Organization of American States. The Expectations about Counseling–Brief form (EAC-B) questionnaire was translated and administered to 488 subjects across age, sex, and experience with psychological services. Subsequent analyses supported the reliability and robustness of the Spanish EAC-B, with factor structure similar to the EAC-B in English. Some relation was found among age, sex, prior counseling experience, and expectations about counseling. Implications of these data for future research and comparison with U.S. subjects are discussed. (PsycINFO Database Record (c) 2010 APA, all rights reserved)     

Properties of poly(ethylene terephthalate)–poly(ethylene naphthalene 2,6‐dicarboxylate) blends with montmorillonite clay

The production and properties of blends of poly(ethylene terephthalate) (PET) and poly(ethylene naphthalene 2,6‐dicarboxylate) (PEN) with three modified clays are reported. Octadecylammonium chloride and maleic anhydride (MAH) are used to modify the surface of the montmorillonite–Na⁺ clay particles (clay–Na⁺) to produce clay–C18 and clay–MAH, respectively, before they are mixed with the PET/PEN system. The transesterification degree, hydrophobicity and the effect of the clays on the mechanical, rheological and thermal properties are analysed. The PET–PEN/clay–C18 system does not show any improvements in the mechanical properties, which is attributed to poor exfoliation. On the other hand, in the PET–PEN/clay–MAH blends, the modified clay restricts crystallization of the matrix, as evidenced in the low value of the crystallization enthalpy. The process‐induced PET–PEN transesterification reaction is affected by the clay particles. Clay–C18 induces the largest proportion of naphthalate–ethylene–terephthalate (NET) blocks, as opposed to clay–Na⁺ which renders the lowest proportion. The clay readily incorporates in the bulk polymer, but receding contact‐angle measurements reveal a small influence of the particles on the surface properties of the sample. The clay–Na⁺ blend shows a predominant solid‐like behaviour, as evidenced by the magnitude of the storage modulus in the low‐frequency range, which reflects a high entanglement density and a substantial degree of polymer–particle interactions. Copyright © 2005 Society of Chemical Industry     

Long-term transients in a reactor under forced concentration cycling

In the approach to a cycle-invariant state in the forced feed concentration cycling of the CO oxidation over a NiO catalyst, a very long transient has been observed lasting 80 ks or more. This transient appears to be associated only with CO pretreatment of the catalyst and is not a general phenomenon. The slow convergence to the cycle-invariant state reported in certain modelling calculations in the literature appears to have a different cause.     

Dynamical modelling of an activated sludge system of a petrochemical plant operating at high temperatures.

The Mexican petrochemical industry, Morelos S.A. de C.V., is one of the biggest and more important petroleum industries in Mexico and Latin America. It has an activated sludge system to treat its wastewater flow, which is approximately 7,000 m3/d. The wastewater contains volatile organic carbon substances classified as toxics. The old surface aeration system was changed for fine bubble diffusers; however, one major drawback of the new aeration system is that the temperature in the bioreactor has increased due to the compression of the air, which at the compressor exit reaches 85 degrees C. This effect results in the temperature in the bioreactor attaining 32 degrees C during the fall, whereas in the spring and summer, the bioreactor temperature reaches higher values than 40 degrees C. The high temperatures reduce the microorganism activity and cause a higher volatilisation rate of volatile compounds, among other effects, which affect the performance of the biological treatment. This work was performed to obtain a better modelling of the wastewater treatment from the petrochemical industry. The model describes the effect of the temperature on the performance of the biological treatment. The model was obtained from tests that were carried out in laboratory reactors with 14 L capacity, which were operated at different temperatures (from 30 to 45 degrees C), with the same wastewater and conditions as the actual system.     

Inverted Solution Processable OLEDs Using a Metal Oxide as an Electron Injection Contact.

A new type of bottom‐emission electroluminescent device is described in which a metal oxide is used as the electron‐injecting contact. The preparation of such a device is simple. It consists of the deposition of a thin layer of a metal oxide on top of an indium tin oxide covered glass substrate, followed by the solution processing of the light‐emitting layer and subsequently the deposition of a high‐workfunction (air‐stable) metal anode. This architecture allows for a low‐cost electroluminescent device because no rigorous encapsulation is required. Electroluminescence with a high brightness reaching 5700 cd m^–2 is observed at voltages as low as 8 V, demonstrating the potential of this new approach to organic light‐emitting diode (OLED) devices. Unfortunately the device efficiency is rather low because of the high current density flowing through the device. We show that the device only operates after the insertion of an additional hole‐injection layer in between the light‐emitting polymer (LEP) and the metal anode. A simple model that explains the experimental results and provides avenues for further optimization of these devices is described. It is based on the idea that the barrier for electron injection is lowered by the formation of a space–charge field over the metal‐oxide–LEP interface due to the build up of holes in the LEP layer close to this interface.     

Capture of Airborne Particulate Using Surface Applied Emulsions: Potential for Postdetonation Dirty Bomb Cleanup

Recent research has proposed the use of asphalt and tall-oil-pitch emulsions for stabilizing radioactive contamination deposited on surfaces in urban areas. The objective of this project was to investigate whether surface applied emulsions could capture airborne radioactive particulate. Laboratory experiments included wind-blown particulate capture studies using an acrylic column and particulate retainment experiments using a wind box capable of producing wind speeds of 96?km/h. A probe methodology was developed to relate particulate retainment to a tack force on the emulsion surface. Experiments were also performed to determine the potential for such emulsions to absorb particulate matter into their emulsion matrix. Tall-oil-pitch emulsions outperformed asphalt emulsions in terms of particulate retention, tack force, and the ability to absorb magnesium silicate. Both tall-oil-pitch and asphalt emulsions were capable of extracting 22–24?g?m?2 of powder from particulate-laden airflow. Tall-oil-pitch emulsions were capable of retaining as much as 5–10% of magnesium silicate powder applied (i.e., retainment densities of 10–20?g?m?2) even after seven?days of curing and after applying 96.5?km/h (60?mph) wind. Tall-oil-pitch emulsions were able to absorb surface-applied magnesium silicate (approximately 0.1–0.2?g of magnesium silicate per 1.0?g of emulsion within three?days) into their emulsion matrix, preventing the magnesium silicate from being exposed to the external environment. Initial results with these five different emulsion formulations suggested particulate capture was feasible. Future emulsion formulations (i.e., longer curing times with greater acid concentrations) should be tested to optimize this postdetonation response strategy.