Operation of superconducting fault current limiter using vacuum interrupter driven by electromagnetic repulsion force for commutating switch

Using conventional high‐temperature superconducting wire, a model superconducting fault current limiter (SFCL) is made and tested. Solenoid coil using Bi2223 silver sheath wire is so made that inductance is as small as possible and a vacuum interrupter is connected in series to it. A conventional reactor coil is connected in parallel. When the fault current flows in this equipment, superconducting wire is quenched and current is transferred into the parallel coil because of voltage drop of superconducting wire. This large current in parallel coil actuates magnetic repulsion mechanism of vacuum interrupter. Due to opening of vacuum interrupter, the current in superconducting wire is broken. By using this equipment, current flow time in superconducting wire can be easily minimized. On the other hand, the fault current is also easily limited by large reactance of parallel coil. © 2008 Wiley Periodicals, Inc. Electr Eng Jpn, 164(1): 52–61, 2008; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20315     

Thermal stability of reinforced Nb3Sn composite superconductor under cryocooled conditions

Several types of reinforced Nb₃Sn wires have been developed to prevent reduction of superconducting properties by applying a strong electromagnetic force. To fabricate a cryocooled magnet using those reinforced wires, we experimentally measured the minimum quench energy (MQE) under cryocooled conditions of some reinforced Nb₃Sn wires. As a result, it became clear that thermal stability expressed as MQE was controlled by the temperature margin between the temperature of the operating condition and the transition temperature from superconductivity to normal. Using the FEM analysis, it was realized that the cause of the decline in thermal stability for the reinforced wires was the low thermal conductivity of the reinforced materials.     

Beam test of the CsI(Tl) calorimeter for the BELLE detector at the KEK-B factory

We studied the performance of a prototype electromagnetic calorimeter for the BELLE detector at the KEK proton synchrotron for an energy range of 0.25–3.5 GeV. The prototype consisted of an array of 6 × 5 CsI(Tl) crystals with 30 cm length (16.2 radiation lengths) and about 6 cm × 6 cm cross section. The scintillation light of each CsI(Tl) crystal was read out by two large-area PIN photodiodes and charge-sensitive preamplifiers attached at the rear face of the crystal. We measured the energy and position resolution for electrons and the e/π separation for two sets of matrix configurations: one corresponded to the center and the other to the edge of the barrel calorimeter. The overall performance measured by the test proves that the prototype calorimeter is satisfactory for the use in the BELLE detector.     

IMPINGING JET DRYER

In coating and gravure printing, an impinging jet nozzle with high thermal efficiency for drying of coated film was developed.

Trial production 0f 40 kinds of nozzle enables to develop a high-performance impinging jet nozzle with heat transfer coefficient 1.5 times larger than that of current slit nozzle, through measurement of heat transfer coefficient, visualizations of air flow and heat transfer, and measuremenu of jet velocity and turbulence distribution. The purpose of the trial production was to expand a range of high heat transfer and promote turbulence compared with the current nozzle.

Paying attention to mass transfer within gravure ink coated film, drying characteristic of the film was analyzed by numerical solution of a set of equations governing the drying process in which concentration dependencies 0f the diffusion coefficient and the equilibrium vapor pressure were considered.

Applying these analyses. an industrial scale dryer with excellent drying efficiency has finally been developed.     

FDTD analysis of switching characteristics in magnetooptic functional devices using magnetostatic surface waves

Collinear magnetooptic interaction with magnetostatic surface waves (MSSW) can be used for wavelength‐selective switches, wavelength filters, and frequency shifters in wavelength‐division‐multiplexed (WDM) photonic networks and optical processing systems. The switching efficiency can be improved with a multilayer waveguide structure. To investigate the dynamic switching characteristics, the FDTD method was employed. The mode conversion between TE and TM mode was successfully demonstrated with FDTD simulation. The filtering characteristics were also evaluated. The FDTD results were compared with the result from the coupled mode theory, and good agreement was obtained. Switching of an optical pulse was also demonstrated by the FDTD method. © 2007 Wiley Periodicals, Inc. Electr Eng Jpn, 162(1): 40–47, 2008; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20501     

Handling of fine-particles by time-averaged particle driving method in plasmas

We developed a noble technique for the fine-particle handling in plasmas. In this method a pair of point electrodes are introduced in the plasma, to which positive pulses are applied alternatively. When the pulse repetition period is shorter than the particle response time, the particles feel only time-averaged force because of their large mass. Spatial profile of the equivalent potential of the time-averaged force varies from a circle to an ellipse with an increase in the local discharge at the electrodes. The particles are eventually transported toward a middle point between two point-electrodes, being almost independent of their initial positions. This method is quite effective for converging fine particles in the plasma.     

Subcellular localization of Bcl-2 protein in synovial sarcoma

The subcellular localization of Bcl-2 protein in surgically resected, fixed-frozen tissue specimens of seven tumors from six cases of synovial sarcoma and a synovial sarcoma cell line was examined using laser-scanning confocal microscopy and immunoelectron microscopy. Bcl-2 protein in synovial sarcoma cells was detected in the nuclear envelope, endoplasmic reticulum membrane, and mitochondrial circumference. Based on the finding of pre-embedding immunoelectron-microscopy observation, the distribution of Bcl-2 protein in such membranous organella was patchy. A computer-based image analysis failed to reveal any quantitative differences between the inner and the outer mitochondrial membranes. The tumorigenesis of synovial sarcoma is also discussed from the viewpoint of Bcl-2 overexpression.     

Dynamic moduli for short fiber-CR composites

The dynamic moduli, E′ and E″, and tan δ for nylon–CR and PET–CR composites with unidirectional short fibers were studied as a function of temperature by using a Rheovibron. The temperature dependence of tan δ showed two dispersion peaks for nylon–CR composite. The peak at ?28°C corresponded to the main dispersion of CR and the peak at 100°C to the α-dispersion of nylon 6. For a PET-CR composite, in addition to the individual dispersion of CR and PET, a small and broad peak was observed at about 90°C. The angular dependence of E′ indicated that the short fibers assumed good orientation. The storage modulus for the composites was given by the parallel model as E′ = V_f′E_f + V_mE′_m., where E′_c, E′_f and E′_m were the storage modulus for the composite, fiber, and matrix and V_f and V_m were the volume fraction of fiber and matrix, respectively. In the transverse direction of fiber, the peak values of tan δ at ?28°C were given by the following equation; tan δ_c = tan δ_m ? δV_f, where tan δ_c and tan δ_m are the loss tangent for the composite and matrix, respectively, and α is coefficient depending on fiber type. The results indicated that a region with strong interaction was formed between fibers and CR matrix.     

Decomposition of chlorofluorocarbons on TiO2ZrO2

The decomposition of chlorofluorocarbons (CFCs) in the presence of water was examined over a variety of solid acid catalysts. The TiO₂ZrO₂ catalyst was found to have the highest activity and longest life among the catalysts examined. The activity of the TiO₂ZrO₂ catalysts depended upon the content of TiO₂. At the contents of TiO₂ from 58 to 90 mole%, the TiO₂ZrO₂ catalysts exhibited high activity, and these catalysts were proven to contain TiZrO₄ crystal. From the study of the XRD peak intensity of the TiZrO₄ crystal, it was highest on the TZ-58 which contained 58 mole% of TiO₂, and decreased with increasing the content of TiO₂. Furthermore, the conversion of CFC113 measured at 673 K was highest at TZ-58, and decreased gradually with increasing TiO₂ content. Therefore, the TiZrO₄ crystal influences the activity of decomposition of CFC113. However, the TiO₂ZrO₂ catalyst was gradually deactivated during the reaction due to the elimination of titanium atoms. A good relationship was found between the activity on TiO₂ZrO₂ catalyst and bond energy of CCl in the compounds of chlorofluorocarbons and hydrochlorocarbons, suggesting that the rate controlling step was the cleavage of CCl bond.