Genetic based sensorless hybrid intelligent controller for strip loop formation control between inter-stands in hot steel rolling mills

Safe operating environment is essential for all complex industrial processes. The safety issues in steel rolling mill when the hot strip passes through consecutive mill stands have been considered in this paper. Formation of sag in strip is a common problem in the rolling process. The excessive sag can lead to scrap runs and damage to machinery. Conventional controllers for mill actuation system are based on a rolling model. The factors like rise in temperature, aging, wear and tear are not taken into account while designing a conventional controller. Therefore, the conventional controller cannot yield a requisite controlled output. In this paper, a new Genetic-neuro-fuzzy hybrid controller without tension sensor has been proposed to optimize the quantum of excessive sag and reduce it. The performance of the proposed controller has been compared with the performance of fuzzy logic controller, Neuro-fuzzy controller and conventional controller with the help of data collected from the plant. The simulation results depict that the proposed controller has superior performance than the other controllers.     

Efficacy of biogenic silver nanoparticles against clinical isolates of fungi causing mycotic keratitis in humans

Mycotic keratitis is mainly responsible for vision loss caused by various fungi. Sometimes, proper treatment of such infection is not possible due to unavailability of effective antifungal agents and development of resistance of such fungi to antimycotic drugs. Hence, it is necessary to search for potential antifungal agents, which can effectively eradicate fungal infection of eyes. Nanoparticles‐based antifungal drugs overcome this problem by increasing permeability and properties of drug molecules. In the present study, silver nanoparticles were synthesised by using Helminthosporium sp. and Chaetomium sp. following sequential reduction technique. The synthesised silver nanoparticles were detected primarily by UV‐visible spectrophotometer showing absorption spectra at 424 and 433 nm, respectively. Nanoparticles tracking analysis confirmed the mean particle size of silver nanoparticles as 45 and 55 nm. The synthesised AgNPs showed significant antifungal activity against fungi causing mycotic keratitis, when used alone and in combination with ketoconazole and amphotericin B in the range of 30–70 microgram per millilitre of minimum inhibitory concentration. Thus, the synthesised AgNPs can be used to enhance the activities of ketoconazole and amphotericin B.Inspec keywords: silver, nanoparticles, nanomedicine, antibacterial activity, diseases, permeability, ultraviolet spectra, visible spectra, particle sizeOther keywords: biogenic silver nanoparticles, fungi, mycotitic keratitis, vision loss, infection, antifungal agents, antimycotic drugs, antifungal drugs, permeability, Helminthosporium sp, Chaetomium sp, sequential reduction technique, UV‐visible spectrophotometer, mean particle size, ketoconazole, amphotericin B, wavelength 424 nm, wavelength 433 nm, size 45 nm, size 55 nm, Ag     

Multiwalled carbon nanotubes grafted chitosan nanobiocomposite: A prosperous functional nanomaterials for glucose biosensor application

Multiwalled carbon nanotubes (MWNTs) grafted chitosan (CS) nanowire (NW) was prepared by phase separation method. Glucose oxidase (GOx) was sequentially immobilized into MWNT-CS-NW to obtain MWNT-CS-NW/GOx biosensor. Field emission scanning electron microscopy (FESEM) images of MWNT-CS-NW/GOx reveals the existence of MWNT and CS. Cyclic voltammetry and amperometry were used to evaluate the electrochemical determination of glucose. The MWNT-CS-NW/GOx biosensor shows an excellent performance for glucose at +0.34 V with a high sensitivity (5.03 μA/mM) and lower response time (3 s) in a wide concentration range of 1-10 mM (correlation coefficient of 0.9988). In addition, MWNT-CS-NW/GOx biosensor possesses better reproducibility, storage stability and there is negligible interference from other electroactive components.     

Investigation on microstructure and tensile behaviour of stir cast LM13 aluminium alloy reinforced with copper coated short steel fibers using response surface methodology

Copper coated steel fibers reinforced LM13 aluminium alloy composites have been prepared using stir casting process. Experiments have been designed using response surface methodology by varying wt% of reinforcement (0–10), stirrer speed (350–800 rpm) and pouring temperature (700–800 °C). Microstructure, tensile strength and fracture surface of composites have been investigated. Analysis of variance, significance test and confirmation tests have been performed and regressions models have been developed to predict the tensile strength of composites. Response surface plots reveal that tensile strength of composites increases with increasing wt% of copper coated steel fibers reinforcement up to 6 wt%. Further increase in wt% of steel fibers decreases the tensile strength of composites. However tensile strength of composites increases with increasing stirrer speed due to the uniform and homogeneous dispersion of steel fibers in matrix. Optimum stir cast process parameters for obtaining higher tensile strength are found to be 5.9 wt% of reinforcement, 753 °C pouring temperature and stirrer speed of 633 rpm. Fracture mechanism is dominated by steel fiber pullouts in composites with higher wt% of reinforcement and dimples are observed in the surface of composites containing lower levels of wt% of reinforcement.     

Electrospun MgO/Nylon 6 Hybrid Nanofibers for Protective Clothing

Nano-Micro Letters - Magnesia (MgO) nanoparticles were produced from magnesite ore (MgCO3) using ball mill. The crystalline size, morphology and specific SSA were characterized by X-ray diffraction...     

Study of tribofilms formed during dry sliding of Ta2AlC/Ag or Cr2AlC/Ag composites against Ni-based superalloys and Al2O3

Herein we show that dry sliding, in air, in the 25–550 °C temperature range, of the novel Ta₂AlC/20 vol.% Ag and Cr₂AlC/20 vol.% Ag composites against Ni-based superalloys (SAs) and alumina led to the formation of steady-state tribofilms whose thicknesses and compositions varied depending on sliding conditions. At elevated temperatures, under both isothermal and thermocyclic conditions, relatively thick (>0.5 μm) well-compacted “glaze” lubricious tribofilms were developed as a result of joint action of tribo-chemical and tribo-mechanical factors involving repeated tribo-oxidation, mixing, fracturing, sintering, etc. They were mainly composed of oxidized constituents from both counterparts (if slid vs. SA) or solely from MAX-Ag ones (vs. Al₂O₃) and possessed a fine multi-layered microstructure, i.e. a more oxidized thin outermost layer and a less oxidized carbide-containing thicker inner layer. During thermocycling the tribofilms adapted to 25–550 °C temperature variations and preserved their primary macro- and microstructure, hardness, good adhesion to the matrix and lubricating characteristics. Consequently, the tribological properties of MAX-Ag/SA tribocouples did not deteriorate, but slightly improved with sliding distance. A possible mechanism of tribofilm generation and their transformations at various temperatures is discussed. The effect of SA and alumina counterparts on the formation and degradation of the tribofilms are also discussed.