Miscibility and morphology of poly(vinylidene fluoride)/poly[(vinylidene fluoride)‐ran‐trifluorethylene] blends

This study presents an investigation of the effect of the different crystalline phases of each blend component on miscibility when blending poly(vinylidene fluoride) (PVDF) and its copolymer poly[(vinylidene fluoride)‐ran‐trifluorethylene] [P(VDF–TrFE)] containing 72 mol % of VDF. It was found that, when both components crystallized in their ferroelectric phase, the PVDF showed a strong effect on the crystallinity and phase‐transition temperature of the copolymer, indicating partial miscibility in the crystalline state. On the other hand, immiscibility was observed when both components, after melting, were crystallized in their paraelectric phase. In this case, however, a decrease in crystallization temperatures suggested a strong interaction between monomers in the liquid state. Blend morphologies indicated that, in spite of the lack of miscibility in the crystalline state, there is at least miscibility between PVDF and P(VDF–TrFE) in the liquid state, and that a very intimate mixture of the two phases on the lamellar level can be maintained upon crystallization. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 85: 1362–1369, 2002     

Mass transfer in 3D-printed electrolyzers: The importance of inlet effects

This article investigates the effect of inlet shape, entrance length, and turbulence promoters on mass transfer by using 3D-printed electrolyzers. Our results show that the inlet design can promote turbulence and lead to an earlier transition to turbulent flow. The Reynolds number at which the transition occurs can be predicted by the ratio of the cross-sectional area of the inlet to the cross-sectional area of the electrolyzer channel. A longer entrance length results in more laminar behavior and a later transition to turbulent flow. With an entrance length of 550 mm, the inlet design did no longer affect the mass transfer performance significantly. The addition of gyroid type turbulence promoters resulted in a factor of 2 to 4 increase in mass transfer depending on inlet design, entrance length, and the type of promoter. From one configuration to another, there was a minimal variation in pressure drop (<1600 Pa).     

pH sensitive phosphate crosslinked films of starch-carboxymethyl cellulose

This work aims to develop hydrogel films of starch and carboxymethyl cellulose (CMC) crosslinked with sodium trimetaphosphate (STMP) and to characterize some of their properties. Starch and STMP (S/T), starch and CMC (S/C), and mixed (S/T/C) films were prepared by casting. The degree of substitution, morphology, swelling degree, FTIR, mechanical properties, and sorption isotherms were studied. Reticulated samples (S/T and S/T/C) showed the same degree of substitution (0.050 ± 0.001). All films presented homogeneous morphology, but the mixed film showed greater roughness. Crosslinking increased the swelling capacity of the mixed hydrogel at pH 7, although it remained decreased concerning the S/T hydrogel. However, this property was sensitive to pH variations. The mixed film (S/T/C) showed greater mechanical resistance. The casting process was efficient to produce hydrogel films of starch/CMC crosslinked with STMP and the general results demonstrated the advantages of the mixed hydrogel.     

Vapor- and liquid-phase adsorption of alcohol and water in silicalite-1 synthesized in fluoride media

In this work, batch-adsorption experiments and molecular simulations are employed to probe the adsorption of binary mixtures containing ethanol or a linear alkane-1,n-diol solvated in water or ethanol onto silicalite-1. Since the batch-adsorption experiments require an additional relationship to determine the amount of solute (and solvent) adsorbed, as only the bulk liquid reservoir can be probed directly, molecular simulations are used to provide a relationship between solute and solvent adsorption for input to the experimental bulk measurements. The combination of bulk experimental measurements and simulated solute–solvent relationship yields solvent and solute loadings that are self-consistent with simulation alone, and allow for an assessment of the various assumptions made in the literature. At low solution concentrations, the solute loading calculated is independent of the assumption made. At high concentrations, a negligent choice of assumption can lead to systematic overestimation or underestimation of calculated solute loading.     

Effect of natural oils on the thermal stability and degradation kinetics of recycled polypropylene wood flour composites

Recycled polypropylene was reinforced with wood fibers that were non‐treated and treated with different natural oils (hexanoic, octanoic, decanoic and dodecanoic acids). The thermal properties, morphology, kinetics and thermodynamic parameters were investigated. The use of natural oils as coupling agents clearly improved the interfacial adhesion with the matrix and increased the thermal stability of the composites. Octanoic acid improved the thermal stability of the composite the most compared with the other evaluated natural oils. The improvement caused by this natural oil is similar to that promoted by the addition of PPgMA. The thermal stability of the composite was affected by the boiling temperature and the chain length of the acid used. POLYM. COMPOS., 35:1935–1942, 2014. © 2014 Society of Plastics Engineers     

Preparation of monoglycerides by guanidine-catalyzed processes

Glycerolysis of methyl stearate and tristearin has been carried out in the presence of alkylguanidines—strong nonionic bases—as catalysts. When applied at 10 mol%, 1,5,7-triazabicyclo [4.4.0]dec-5-ene, 1,2,3-tricyclohexylguanidine, and 1,3-dicyclohexyl-2-n-octylguanidine give monoglycerides in more than 90% selectivity, in a maximum of 6 h reaction time.     

Leaf and stem micromorphology of Byrsonima sericea DC. by light and scanning electron microscopy

Micromorphological studies were carried out using multiple microscopic techniques on the leaves and stem bark of Byrsonima sericea DC. (Malpighiaceae), a species popularly known as “murici” and used medicinally, in order to identify both qualitative and quantitative features of leaf and stem anatomy and histochemistry as differential parameters to support both the quality control of its ethnodrugs and the taxonomy of the genus. The study was conducted using traditional techniques of plant anatomy, histochemical tests, and the stomatal index (SI). Byrsonima sericea has hypostomatic leaves, anomocytic stomata, and its epidermal walls are anticlinal and straight on the adaxial and curved on the abaxial faces. T‐shaped trichomes were observed mainly on the abaxial surface. The leaf epidermis showed waxes syntopism on both surfaces, with the occurrence of different crystalloid forms on a single phylloplane. The mesophyll is dorsiventral, with 3‐4 collateral vascular bundles. Phenolic compounds, starch, and proteins were identified in the petiole and stem. The SI was 14.5 ± 0.53% (p < .05), but did not showed significant variations. A set of characters were found to be distinctive for the studied species, however, constituting parameters that could be used to separate B. sericea from other species of the genus.     

Analysis of microstructure and microhardness of Zr-2.5Nb processed by High-Pressure Torsion (HPT)

Nanostructured materials have been widely studied due to the improvement of their mechanical properties comparing to those of coarse grain materials. The present work intended to analyze the microstructure and microhardness of Zr-2.5Nb processed by high-pressure torsion (HPT), one of the severe plastic deformation techniques. The deformations were carried out at room temperature using a pressure of 5?GPa and 5 anvil turns. Vickers indentation was used to evaluate the microhardness of the samples. Transmission electron microscopy and X-ray diffraction were used to analyze the microstructure. The results showed a significant refinement from the initial microstructure achieving nanometric grain size around 50?nm and phase transformation α?→?ω?+?β_I induced by shear. The Vickers microhardness values of the material submitted to HPT technique were significantly higher than those of non-deformed material. Also, HPT procedure resulted in a huge grain refinement of the material and in phase transformation.