Passivation effects of deuterium exposure on boron-doped CVD homoepitaxial diamond

The deuterium (hydrogen) passivation effect on acceptors in boron-doped CVD homoepitaxial diamond was studied by electrical (Hall-effect) and secondary ion mass spectroscopy (SIMS) measurements. Deuterium was incorporated into the samples using microwave (MW) deuterium plasma at 673 K for 2–24 h. We observed the progress of acceptor passivation with p-type conduction, which finally resulted in a highly resistive state.     

Rutile-type TiO2 thin film for high-k gate insulator

We investigated rutile-type titanium dioxide (TiO₂) films for possible use as a high-k gate insulator. The TiO₂ thin films were directly deposited on Si substrates using a RF magnetron sputtering method with a sintered oxide target. A single phase of rutile-type TiO₂ whose dielectric constant of approximately 75 was obtained when the film was deposited in an inert gas atmosphere and annealed at 800 °C in an oxidizing gas atmosphere. The oxygen ions were deficient in the as-deposited film, and consequently, a sufficient oxygen supply was needed to crystallize the film to a single phase of rutile during the post-annealing. However, the interfacial SiO₂ layer between the TiO₂ and the Si substrate simultaneously grew thicker than 2 nm. As the interfacial SiO₂ grew, the leakage current was decreased and the equivalent oxide thickness was increased, in the Au/rutile-type TiO₂/Si capacitor. Therefore, we concluded that the growth of the interfacial SiO₂ layer thicker than 2 nm is inevitable to form the single phase of rutile-type TiO₂ and to decrease the leakage.     

Elastic, anelastic, and piezoelectric coefficients of langasite: resonance ultrasound spectroscopy with laser-Doppler interferometry

This paper presents advanced techniques to determine all independent elastic-stiffness coefficients C/sub ij/, the associated internal friction Q/sub ij//sup -1/, and piezoelectric coefficients e/sub ij/ of monocrystal langasite (La/sub 3/Ga/sub 5/SiO/sub 14/) using a single rectangular parallelepiped specimen. Langasite's crystal structure belongs to the trigonal system with point group 32, and thus possesses six independent C/sub ij/, two e/sub ij/, and two dielectric coefficients /spl epsiv//sub ij/. All of the elastic and piezoelectric coefficients affect the mechanical resonance frequencies of the solid specimen, and measuring them very accurately permits one to determine the C/sub ij/ and e/sub ij/ with known density, dimensions, and e/sub ij/. We developed a piezoelectric tripod to support the specimen upward and measured the free-vibration resonance frequencies with minimum load from its own weight. This weak and stable acoustic coupling ensures accuracy of the frequency measurement better than 10/sup -5/, enough to determine the coefficients reliably. Our C/sub ij/ fall in the range of results measured with previous (conventional) methods. Our e/sub 11/ is smaller than the reported values by 1.2-13%, and e/sub 14/ is larger by 44-97%. For the internal friction measurement, we used a solenoid coil to vibrate the specimen without any contact. The longitudinal-wave internal friction considerably exceeds the shear-wave internal friction, which can be explained by phonon-phonon interactions.     

An Electronic Approach to Materials Design

A molecular orbital approach to materials design has recently made great progress. This approach is based on the electronic structure calculations by the DV-Xα cluster method. In this paper recent progress in this approachis reviewed. In particular     

Synthesis and applications of fluoroalkyl end-capped cooligomers having fullerene and mixed fullerenes in the main chain

Fluoroalkanoyl peroxides reacted with FULLERENES [fullerene (C₆₀) and commercially available fullerenes (Nanom Mix^TR and Nanom Black^TR)] and radical polymerizable comonomers such as acrylic acid, N,N-dimethylacrylamide, N-(1,1-dimethyl-3-oxobutyl)acrylamide, and acryloylmorpholine to afford fluoroalkyl end-capped cooligomers having FULLERENES in the main chain under very mild conditions. Fluoroalkyl end-capped Nanom Mix and Nanom Black cooligomers thus obtained were found to exhibit a similar solubility to that of the corresponding fluoroalkyl end-capped cooligomers having fullerene in the main chain. These fluorinated FULLERENES cooligomers were found to form the nanometer size-controlled self-assembled cooligomeric aggregates in aqueous solutions. These fluoroalkyl end-capped FULLERENES cooligomers were more effective for solubilizing fullerene, Nanom Mix and Nanom Black into water, compared to those of the corresponding fluoroalkyl end-capped homooligomers having no FULLERENES in the main chain. Fluoroalkyl end-capped fullerene- and Nanom Mix-acrylic acid cooligomers were found to exhibit fluorescence spectra related to fullerene and Nanom Mix in cooligomers, respectively, in aqueous solutions. Additionally, these fluorinated fullerene- and Nanom Mix-acrylic acid cooligomers were able to increase chemiluminescence intensity related to luminol, effectively, compared to the corresponding fluorinated acrylic acid homooligomers.     

Multiobjective dynamic load-dispatching method for optimal operation of power systems

A new practical method is proposed which gives a quasi-optimal solution of the dynamic load-dispatching problem formulated by a multiconstraint multiobjective optimization problem. Here, the multiple constraints are rate reserve constraints and power flow ones, and the multiple objectives are fuel cost and CO₂ emission. The proposed method is an integration of the following three techniques: (1) “Group Dispatch Scheme,” which is developed by the authors, is used to satisfy a violated constraint easily. This scheme consists of three steps. The first step is to classify all generators into two groups. One is the group which should be more loaded to satisfy the violated constraint, and the other is the should-be less loaded group. The second step is to add some load to the former group, and to subtract the same load from the latter. The third step is to dispatch each group load to each groups generators, respectively; (2) the dynamic load-dispatching algorithm is used which provides, in practical time, quasi-optimal generation trajectories; (3) the conventional weighting parametric method is used to obtain a Pareto optimal solution of multiobjective problems. The effectiveness of the method is clarified by a computer simulation on the actual power system of Kansai Electric Power Company.     

Crystallization of potassium titanate from the amorphous phase

By using amorphous potassium titanates as the starting materials, a sintered body of K₂Ti₄O₉ or K₂Ti₆O₁₃ with porous and fibrous textures was prepared. K₂Ti₂O₅ and a new phase, K₆Ti₄O₁₁ were synthesized by the thermal reaction of KNO₃ with TiO₂ at 1000° C for 10 to 20 h. On leaching in water to expel excess of potassium ions, both phases became amorphous. After mixing and moulding these amorphous materials in the desired proportion, a sintered body containing fibrous crystals of K₂Ti₄O₉ was readily fabricated by heating at 1000° C for 12 h. When 5 wt % B₂O₃ was added to the amorphous phases, single phase K₂Ti₆O₁₃, with a fibrous texture grew well on heating at 1000° C for 12 h. Addition of PVA polymer to the amorphous phases was responsible for controlling the porosity of the sintered body, e.g. about 52% theoretical density at 20 wt% PVA polymer. The optimum conditions for preparing the amorphous phases were systematically examined and the effect of the chemical reaction environments, such as different crucible materials on the calcination of KNO₃ and TiO₂ were also discussed.     

Strength and Fracture Toughness of Isostatically Hot-Pressed Composites of Al2O3 and Y2O3-Partially-Stabilized ZrO2

Composites of Al₂O₃ and Y₂O₃ partially-stabilized ZrO₂ were isostatically hot-pressed using submicrometer powders as the starting material. The addition of Al₂O₃ resulted in a large increase in bending strength. The average bending strength for a composite containing 20 wt% Al₂O₃ was 2400 MPa, and its fracture toughness was 17 MN·w^−3/2     

New software developments for quality mesh generation and optimization from biomedical imaging data

In this paper we present a new software toolkit for generating and optimizing surface and volumetric meshes from three-dimensional (3D) biomedical imaging data, targeted at image-based finite element analysis of some biomedical activities in a single material domain. Our toolkit includes a series of geometric processing algorithms including surface re-meshing and quality-guaranteed tetrahedral mesh generation and optimization. All methods described have been encapsulated into a user-friendly graphical interface for easy manipulation and informative visualization of biomedical images and mesh models. Numerous examples are presented to demonstrate the effectiveness and efficiency of the described methods and toolkit.