Effects of Surface Concentration on Drying Behavior of Carbohydrate Solutions

As the surface properties of the drying materials are very important not only for the drying rate but also for the quality change during drying, the effects of surface concentration on the drying behavior of liquid foods (sugar solutions) were investigated by isothermal drying experiments and by numerical calculation experiments. The isothermal drying experiments with gelled sugar solution systems (sucrose and maltodextrin) were carried out at various relative humidity (RH) values (RH = 0 to 84%). Separate experiments were carried out for determination of the desorption isotherms.

The isothermal drying curves of sugar solutions at RH = 0 to 51% were very similar. Numerical simulations also showed that the drying curves of these sugars at the surface concentration = 0 and 0.1 are almost the same, although the concentration distributions are different.

When a small amount of gelatin was added to sugar solutions, the drying rate decreased remarkably as the gelatin might form a thin film (skin) near the surface, and consequently the retention of ethanol increased.     

Preparation of polyimide-epoxy composites

The formation of a three dimensional network of crosslinked epoxy leads all unmodified epoxies to have inherent brittleness and relatively low degradation temperatures. Polyimides, on the other hand, are widely used for applications that require high degrees of flexibility and thermal resistance. Here, we have focused on the preparation of epoxy systems cured with polyamic acids instead of traditional amino-group-containing hardening agents. The cure behavior and potential reaction mechanisms of EPON 828 resin and polyamic acid mixtures were evaluated by DSC and TGA. Thermal analysis showed a complex reaction sequence taking place in the mixture and also determined the extent of reaction of the polyamic acid with itself and the competitive reaction of the polyamic acid with the epoxy. The compositions of the mixtures were varied to see the dependence of the cure behavior on component concentrations. Solutions of the two components did not phase separate and also phase separation was not apparent either optically or microscopically in the cured samples. This phase behavior was attributed to a unique in situ reaction. A novel solvent system for the polyamic acid precursor was also used.     

An equation of state for 1,1-difluroethane (HFC 152a)

An equation of state for 1,1-difluoroethane (HFC 152a, CH₃CHF₂) has been developed on the basis of reliable experimental data including PVT, liquid C_p, and saturated-liquid-density data measured by our group. It is a non-dimensionalized virial equation whose functional form is the same as that originally developed for 1,1,1,2-tetrafluoroethane (HFC 134a) in our group. The effective range is for pressures up to 15 MPa, temperatures from 230 to 450 K, and densities to 1000 kg m⁻³. The equation represents reliable PVT measurements within ± 1% in pressure for the superheated vapour and supercritical fluid, while within ±0.5% in density for the compressed liquid. In addition, it should be noted that the equation represents the other essential thermodynamic properties including vapour pressures, saturated-liquid/ vapour densities, isobaric/isochoric specific heats and sound velocity in both the liquid and gaseous phase of HFC 152a.     

Impulse breakdown voltages of triggered multistage vacuum gap

Several sealed-off triggered vacuum gaps are connected in series to improve hold-off voltage. The characteristics of impulse breakdown voltage of these series-connected gaps are investigated experimentally. The sum hold-off voltage of series-connected gaps decreases to a unit hold-off voltage when the maximum value of voltage division ratio across the gaps increases to unity. Self-breakdown probability of the series-connected gaps is always higher than that of a single gap under the same conditions. Hence, stage efficiency of the multistage gap decreases with increasing number of stages. Its value is 90 percent with 2-stage gap and 75 percent with 5-stage gap, respectively, under the same voltage division ratio and the same gap length (2.0 mm) in each stage. Triggered breakdown voltage of 2- or 3- stage gap is several hundred volts when all gaps are triggered simultaneously at the peak of the main impulse wave and a working voltage range is nearly 100 percent in this case. The working voltage range decreases with number of stages. Its value is 45 percent with 3-stage gap and 15 percent with 5-stage gap, respectively, when one triggered gap is fired for switching.     

Silica removal from Mokai, New Zealand, geothermal brine by treatment with lime and a cationic precipitant

Preliminary experiments using two chemicals (CaO, a quicklime, and a cationic nitrogen-bearing precipitant, EC-004) to remove silica from geothermal brine were undertaken at the Mokai geothermal plant, New Zealand. The brine was mixed with the reagent (CaO or EC-004). The reaction was studied from the start of the experiment (NRT, 0 min, no retaining time) and after 15 min (15RT) at 90 °C. The concentration of silica in the brine was initially 954 mg/l, and decreased linearly with increasing reagent concentration. When CaO is added, the silica concentration at 15RT was 200 mg/l lower than at NRT and became almost zero on addition of 1.5 g/l. In contrast, when EC-004 is added, the total silica concentration nearly reaches the solubility of amorphous silica at 90 °C. In order to prevent silica scaling in Mokai brines cooled to 90 °C, the CaO and EC-004 added should be individually adjusted to 0.5 g/l and 80 mg/l, respectively.     

Surface Hardening of Carbon Steel Using High Powered YAG Laser

A high powered YAG laser with kaleidoscope for surface modification was applied to the surface hardening of carbon steels containing 0. 18-0.54 wt% C without the absorbents, and the relationships between laser processing and surface hardening were investigated by hardness and microstructure. The structure of the hardened zone underwent complete martensitic transformation in all of the carbon steels tested, and its hardness increased with greater carbon content. Under identical irradiated conditions, the hardened zone expanded with increasing carbon content. A hardened zone extending from the surface to a depth of 1.0 mm was obtained at a laser power of 1.0 kW and a scanning speed of 1 mm/sec. It was found that in the surface hardening of carbon steels, a high powered YAG laser can be used to control the hardened zone by selecting the appropriate irradiation conditions, however, the hardened zone was affected by the assistant gas and the flow rate.     

Far-Infrared Reflection Spectra of Dielectric Ceramics for Microwave Applications

Far-infrared reflection spectra of dielectric ceramics, BaSm₂Ti₅O₁₄, BaTi₄O₉, and some pcrovskites such as Ba(Zn_1/3Nb_2/3)O₃, have been measured at room temperature using a Fourier transform infrared spectrometer in order to investigate the effect of the crystal structure on the dielectric properties. As for perovskites, Sr(Zn_1/3Nb_2/3)O₃ and Sr(Mg_1/3Nb_2/3)O₃, in which B site ions are ordered, were also measured. Reflectance data were analyzed by means of a factorized form of dielectric functions instead of the classical dispersion theory, and all of the spectra were well fitted. The values of dielectric constants and tan δ calculated from the reflectance data were in good agreement with resonant cavity measurements at 5 GHz. Furthermore, results of this study have shown that the main contribution to the microwave dielectric properties is caused by low-frequency optically active modes located at 50 to about 300 cm⁻¹, and for perovskite structures it is suggested that the ordering of B site ions is significant in obtaining low dielectric losses.     

Expert system for dispatch control in restoration of ehv power system after complete blackout

Present-day power systems operate with high reliability, and it is rare that a blackout will extend over an entire system swiftly and securely. This paper considers automatic power supply to loads after a complete blackout of a system. First, taking into account characteristics of generators, loads, and initial power sources, a method is proposed of allocating several generators to each load in parallel to the system and supplying power to the load sequentially. Second, to remove the imbalance between supply and demand of power, a method is proposed of adjusting the amount of supply and generation according to a present imbalance and the sum of past ones. Third, to automatically issue orders for start-up, parallel, follow-up, stand-by, and stoppage of generators, several rules for each power station are set and an expert system is made based on them. Finally, the expert system is applied to a model power system, and it is verified that it can restore loads without any trouble for a complete blackout which occur at any time of a day and in any restoration pattern.     

Stability of protective oxide films in waste incineration environment—solubility measurement of oxides in molten chlorides

Solubility measurements of several oxides in molten NaCl-KCl and NaCl-KCl-Na₂SO₄-K₂SO₄ were conducted in three different levels of basicity. The dissolution behavior of the oxides showed almost the same tendency as that shown by the dissolution behavior of the oxides in molten Na₂SO₄ in literature. In a waste incineration environment, a protective Cr₂O₃ film easily dissolves in molten chlorides as CrO₄²⁻ because pO²⁻ of the molten chlorides tends to have a small value due to the effect of water vapor contained in the combustion gas. From the result of the solubility measurement, the addition of molybdenum and/or silicon was expected to improve the corrosion resistance of alloys. Laboratory corrosion tests confirmed this expectation. However, the scale analysis suggested that the effect of molybdenum could not be explained completely by only the mechanism derived from the result of the solubility measurement.     

High-Temperature Fracture Mechanism of Low-Ca-Doped Silicon Nitride

High-purity Si₃N₄ (with 2.5 wt% glassy SiO₂) doped with 0 to 450 at.ppm of Ca was prepared as a model system to investigate the effects of grain-boundary segregants on fracture phenomenology at 1400°C. Subcritical crack-growth (SCG) resistance as well as creep resistance was degraded significantly by the presence of a small amount of Ca. The internal friction of the doped materials exhibited the superposition of a grain-boundary relaxation peak and a high-temperature background, and the apparent viscosity of the grain-boundary film was determined from the peak. Based on these experimental data, the fracture mechanism at 1400°C was divided into three regions: "brittle," SCG, and creep failure as a function of both external strain rate and Ca concentration, C _Ca. From the investigation of the C _Ca dependence of the critical strain rate for the transition from "brittle" to SCG fractures, the SCG phenomenon is suggested to be triggered by small-scale, grain-boundary sliding. The C _Ca dependence of "steady-state" creep rate was far from the theoretical dependence of diffusional creep via a solution-precipitation mechanism. The discrepancy was interpreted to be due to the presence of an impurity-insensitive creep component. This component may correspond to the lowest limit of the tensile creep rate in Si₃N₄ polycrystalline materials containing intergranular glassy-SiO₂ film.