Bryostatin 1 induces ubiquitin COOH-terminal hydrolase in acute lymphoblastic leukemia cells

It has been previously reported that Bryostatin 1 (Bryo1) induces differentiation of the human acute lymphoblastic leukemia (ALL) cell line, Reh, to a monocytoid B-cell stage. In this study we demonstrate that a novel protein, ubiquitin COOH-terminal hydrolase (UCH-L1), is associated with this differentiation. Reh cells were treated with 200 nmol/l of Bryo1 for 72 h and analyzed for changes in morphology, surface immunophenotype, acid phosphatase and terminal deoxynucleotidyl transferase. Protein patterns of the parent and differentiated cells, by two-dimensional polyacrylamide gel electrophoresis (2D PAGE), were studied. Bryo1-treated cells expressed morphologic, phenotypic and enzymatic features of the monocytoid B-cell stage. The UCH-L1 enzyme (MW-pl 34-5.3) was detected by 2 D PAGE in the differentiated, but not in parent cells. The presence of UCH-L1 in the Bryo1-treated cells was further confirmed by immunoblotting of 2 D PAGE using UCH-L1 polyclonal antibody. Ubiquitin expression was studied in parent and Bryo1-treated cells and was compared with 12-O-tetradecanoylphorbol-13-acetate (TPA)-treated cells. Both agents, TPA and Bryo1, increased the level of ubiquitin expression as detected by flow cytometry. Sodium borohydride, an inhibitor of UCH-L1, inhibited the Bryo1-induced differentiating effect on Reh cells. To date, the mechanism by which Bryo1, exerts its B-cell differentiating effect is not fully understood. This study shows that UCH-L1 expression may play a major role in Bryo1-induced differentiation in pre-B-ALL.     

Redistribution of impurity during recrystallization of alite in portland cement clinker

The redistribution of impurity in alite during recrystallization has been confirmed by means of the electron probe microanalysis. Each of the main impurity components shows a significant decrease in content during recrystallization. This demonstrates that the growth velocity of alite exerts influence on the amount of the impurity taken up in alite in solid solution from the interstitial melt. Whether M₃ or M₁ occurs at ambient temperature depends on the cooling rate of clinker as well as the chemical composition of alite.     

Effect of polymer density on polyethylene hollow fiber membrane formation via thermally induced phase separation

Microporous high‐density polyethylene (HDPE) and low‐density polyethylene (LDPE) hollow fiber membranes were prepared from polyethylene–diisodecyl phthalate solution via thermally induced phase separation. Effect of the polyethylene density on the membrane structure and performance was investigated. The HDPE membrane showed about five times higher water permeability than the LDPE membrane because it had the larger pore and the higher porosity at the outer membrane surface. The formation of the larger pore was owing to both the initial larger structure formed by spinodal decomposition and the suppression of the diluent evaporation from the outer membrane surface due to the higher solution viscosity. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 93: 471–474, 2004     

Studies on phase separation rate in porous polyimide membrane formation by immersion precipitation

Phase separation rate during porous membrane formation by immersion precipitation was investigated by light scattering in a polyimide/N‐Methylpyrrolidone (NMP)/water system. In the light scattering measurement, plots of scattered intensity against scattered angle showed maxima in all cases, which indicated that phase separation occurred by a spinodal decomposition (SD). Characteristic properties of the early stage of SD, such as an apparent diffusion coefficient D_app and an interphase periodic distance Λ, were obtained. The growth process of Λ was also followed by light scattering. The growth rate had the same tendency as D_app when water content in the nonsolvent bath and the polymer concentration in the cast solution were changed. The pore size of the final membrane increased with decreasing water content, which was opposite to the tendency of Λ growth rate. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 292–296, 2003     

Tribological Characteristics of SiC Ceramics in High-Temperature and High-Pressure Water

The effects of temperature and sliding speed on the tribological behavior of a SiC ceramic by sliding on the same material in deoxygenated water were investigated from room temperature to 300°C under the corresponding saturated vapor pressures. The friction coefficient and specific wear rates of both plates and disks increased at elevated temperatures at all sliding speeds, but decreased with increasing sliding speed at 120° and 300°C. Fine mirrorlike worn surfaces were observed without wear debris under all sliding conditions. The wear mechanism appears to consist of hydrothermal oxidation of SiC and dissolution of reaction products such as silica.     

Stick-slip motion control based on cutter location data for an orthogonal-type robot

In this article, a new desktop orthogonal-type robot, which has the capacity of stick-slip motion control based on cutter location data, is presented for lapping small metallic molds with a curved surface. The robot consists of three single-axis devices with a high position resolution of 1 μm. A thin wooden stick tool with a ball-end shape is attached to the tip of the z-axis. In order to improve the lapping performance, a novel stick-slip motion control method is developed in the control system. The small stick-slip motion is orthogonally generated in the direction of the tool’s movement. The effectiveness of stick-slip motion control is examined through an actual lapping test of an LED lens cavity.     

iOS application for quadrotor remote control

With the progress of electronics technology, the development of civilian UAV (unmanned aerial vehicle) applications becomes possible. In addition, smartphones have rapidly gained popularity and become very important due to the simple operability and mobility. Hence, there is a need to have an easy and flexible way to control a UAV using such technology. In this study, a remote controller using an iOS device is developed for a quadrotor to enable remote control with easy operations. Four basic programs for obtaining compass information, controlling a gimbal, autopilot function for return, and video preview function are developed and implemented for an iOS device. The basic functionalities of the programs are evaluated and confirmed through experiments using a quadrotor and an iOS device.