Synthesis of ZSM‐5 Films and Monoliths with Bimodal Micro/Mesoscopic Structures

A route to synthesize ZSM‐5 crystals with a bimodal micro/mesoscopic pore system has been developed in this study; the successful incorporation of the mesopores within the ZSM‐5 structure was performed using tetrapropylammonium hydroxide (TPAOH)‐impregnated mesoporous materials containing carbon nanotubes in the pores, which were encapsulated in the ZSM‐5 crystals during a solid rearrangement process within the framework. Such mesoporous ZSM‐5 zeolites can be readily obtained as powders, thin films, or monoliths.     

Passive alignment method of polymer PLC devices by using a hot embossing technique

A novel fabrication process using a hot embossing technique has been developed for micromechanical passive alignment of polymer planar lightwave circuit (PLC) devices. With only one step of embossing, single-mode waveguide straight channels and micropedestals for passive aligning are simultaneously defined on a polymer thin film with an accuracy of /spl plusmn/0.5 /spl mu/m. This process reduces the steps for fabricating alignment structures. A fabricated polymer PLC chip and fibers are combined on a v-grooved silicon optical bench (SiOB) in a flip-chip manner. The process provides a coupling loss as low as 0.67 dB per coupling face and a cost-effective packaging solution for various polymer PLC devices.     

Hydrogen annealing effect on DC and low-frequency noise characteristics in CMOS FinFETs

The hydrogen annealing process has been used to improve surface roughness of the Si-fin in CMOS FinFETs for the first time. Hydrogen annealing was performed after Si-fin etch and before gate oxidation. As a result, increased saturation current with a lowered threshold voltage and a decreased low-frequency noise level over the entire range of drain current have been attained. The low-frequency noise characteristics indicate that the oxide trap density is reduced by a factor of 3 due to annealing. These results suggest that hydrogen annealing is very effective for improving device performance and for attaining a high-quality surface of the etched Si-fin.     

Inside Front Cover: The Elastic Properties and Plastic Behavior of Two‐Dimensional Polymer Structures Fabricated by Laser Interference Lithography (Adv. Funct. Mater. 10/2006)

The probing of the micromechanical properties within a two‐dimensional polymer structure with sixfold symmetry fabricated via interference lithography reveals a nonuniform spatial distribution in the elastic modulus “imprinted” with an interference pattern in work reported by Tsukruk, Thomas, and co‐workers on p. 1324. The image prepared by M. Lemieux and T. Gorishnyy shows how the interference pattern is formed by three laser beams and is transferred to the solid polymer structure. The elastic and plastic properties within a two‐dimensional polymer (SU8) structure with sixfold symmetry fabricated via interference lithography are presented. There is a nonuniform spatial distribution in the elastic modulus, with a higher elastic modulus obtained for nodes (brightest regions in the laser interference pattern) and a lower elastic modulus for beams (darkest regions in the laser interference pattern) of the photopatterned films. We suggest that such a nonuniformity and unusual plastic behavior are related to the variable material properties “imprinted” by the interference pattern.     

Transmission performance of 10-Gb/s 1550-nm transmitters using semiconductor optical amplifiers as booster amplifiers

We have demonstrated the transmission performance of 10-Gb/s transmitters based on LiNbO/sub 3/ modulator using semiconductor optical amplifiers (SOAs) as booster amplifiers. Utilizing the negative chirp converted in SOAs and self-phase modulation induced by high optical power, we can successfully transmit 10-Gb/s optical signals over 80 km through the standard single-mode fiber with the transmitter using SOAs as booster amplifiers. SOAs can be used for booster amplifiers with a careful adjustment of the operating conditions. In order to further understand an SOA's characteristics as a booster amplifier, we model SOAs and other subsystems to verify the experimental results. Based on the good agreement between the experimental and simulation results, we can find the appropriate parameters of input signals for SOAs, such as extinction ratio, rising/falling time, and chirp parameter to maximize output dynamic range and available maximum output power (P/sub o,max/).     

A printer model using signal processing techniques

An accurate printer model that is efficient enough to be used by halftoning algorithms is proposed. The proposed signal processing model (SPM) utilizes a physical model to train adaptive linear combiners (ALCs), after which the average exposure of each subpixel for any input pattern can be calculated using the optimized weight vector. The SPM can be used to model multi-level halftoning and resolution enhancement, as well as traditional halftoning. The SPM is comprised of a single ALC layer followed by a peak-to-average ratio (PAR) correction layer, which serves to produce a PAR of less than 1.5 in the modeled exposure. The PCN (PAR correction network) employs one ALC/pixel and exploits the physics governing the characteristics of exposure in small regions. A relatively small number of training patterns suffices to train the SPM.     

Wireless-adaptive fair scheduling for multimedia stream

As packet cellular networks are expected to support multimedia services, the authors incorporate the multimedia QoS requirements into the design of a new scheduling algorithm. The proposed wireless-adaptive fair scheduling tries to allocate time slots for each user with fair share by considering the varying channel condition while reflecting the stream requirements and achieving high throughput.     

Abnormal junction profile of silicided p+/n shallowjunctions: a leakage mechanism

The leakage mechanism in p⁺/n shallow junctions fabricated using Co silicidation and shallow trench isolation processes has been investigated using transmission electron microscopy (TEM) combined with selective chemical etching. TEM and TSUPREM-4 simulation results show that dopant profiles bend upward near the edge of the active region. The formation of the abnormal profile is attributed to transient enhanced diffusion induced by source/drain implantation. Based on the TEM and simulation results, it is suggested that the shallower junctions formed near the active edge can serve as a source for leakage current in the silicided p+ /n shallow junctions     

Model-based monitoring of diamond turning process using cross entropy

This paper discusses the model-based monitoring as one of key steps toward building an inprocess diagnostic tool for the supervisory level control in diamond turning. In particular, estimation of surface profile from a nonlinear force model and model-based monitoring of tool chipping are demonstrated. Classification rule is based on the minimization of information-theoretic measure called the cross entropy. The experimental results indicate that monitoring strategy based on the minimum cross entropy guarantees the consistent and optimum classification results in the presence of varying cutting conditions. In addition, the cross entropy as a criterion for indicating the dynamic quality of machine-tool is explained.     

The effect of topical corticosteroids on refractive outcome and corneal haze after photorefractive keratectomy

BACKGROUND: The effect of topical corticosteroids after excimer laser photorefractive keratectomy (PRK) remains a matter of some controversy. Refractive effects may be different according to the amount of myopia and timing of instillation. METHODS: Two groups of patients were studied: Study A consisted of 215 eyes (128 patients) with PRK (mean baseline myopia, -6.53 +/- 2.22 D) that received no corticosteroids (No Corticosteroid Group) unless significant regression or corneal haze appeared (Delayed Corticosteroid Group), and in Study B, we randomly assigned eyes to the Initial Corticosteroid Group (mean baseline myopia, -6.39 +/- 1.84 D) or the No/delayed Corticosteroid Group (mean baseline myopia -5.78 +/- 2.02 D). Clinical results after PRK for low-to-moderate and high myopia were compared. RESULTS: In the first group, 70.9% (73 eyes) of moderately myopic eyes (mean, -4.56 +/- 1.10 D) belonged to the No Corticosteroid Group that had a mean refraction of -5.39 +/- 1.77 D. Delayed Corticosteroid Group eyes were more myopic (mean, -7.52 +/- 2.10 D), and showed more severe haze than those in the No Corticosteroid Group. In study B, only in high myopes with more than -6.00 D (mean, -7.76 +/- 1.15 D) did refraction and corneal haze outcomes show significant difference between the Initial Corticosteroid Group and the No/delayed Corticosteroid Group. CONCLUSIONS: The effects of topical corticosteroids after PRK were less in moderate myopes compared to high myopes. Delayed instillation of corticosteroids did not reverse the regression or haze whereas initial instillation showed a beneficial effect on high myopes but not on moderate myopes.