Effect of polyurethane surface chemistry on its lipid sorption behavior

The relationships among surface, bulk properties and lipid sorption behaviors of segmented polyurethanes (SPUs) with various polyol soft segments were investigated. The polyols used in this study were poly(ethylene oxide) (PEO), poly(tetramethylene oxide) (PTMO), and poly(dimethylsiloxane) (PDMS). The hard segment of these segmented polyurethanes was composed of 4,4'-diphenylmethane diisocyanate and 1,4-butanediol, present at 50 wt%. X-ray photoelectron spectroscopic (XPS) and dynamic contact angle measurements were carried out in order to analyze the surface chemical structure in the air- and water-equilibrated states. XPS revealed that in the air-equilibrated state, lower surface free energy components were enriched at the air-solid interface, whereas in the water-equilibrated state, higher surface free energy components were enriched at the water-solid interface. The change in environment from air to water induced the surface reorganization in order to minimize interfacial free energy. Lipid sorption behaviors of SPUs were investigated by means of infrared spectroscopy. Even after extensive rinsing of the surface, the amount of lipid present on the SPU surface was more than that calculated on the assumption that a monolayer covers the SPU surface. Therefore, the lipid was not only adsorbed on the surface of SPU but absorbed into SPU. The SPU with hydrophilic PEO sorbed larger amount of phospholipid compared with that with hydrophobic polyol such as PTMO and PDMS. Also, the competitive sorption behaviors of phospholipid and cholesterol from their mixed liposome solution were studied. The ratio of sorbed cholesterol to phospholipid increased with an increase in surface hydrophobicity owing to the hydrophobic nature of cholesterol.     

Effects of nondensifying inclusions on the densification and microstructure of zinc oxide matrix composites

The densification and microstructure development of ZnO containing Zn₇Sb₂O₁₂, ZrO₂, and aggregated ZnO were investigated to elucidate the effect of nondensifying inclusions on the sintering of ceramic/ceramic composites. The inclusion retarded the densification, and the degree of retardation was found to depend on the chemical species of inclusion; Zn₇Sb₂O₁₂ had the largest effect, followed by ZrO₂ and then aggregated ZnO last. The experimental results for aggregated ZnO was explained by the theory which predicts the generation of backstresses. The backstresses give a less significant effect on the densification. For Zn₇Sb₂O₁₂ and ZrO₂, the microstructure of the matrix varied with distance from an inclusion particle; much porosity was observed in the region surrounding the inclusion. Circumferential voids, which are responsible for the suppression of densification, form during the initial stage of sintering. Inclusion particles generate an anchoring effect which retards the densification of the matrix immediately surrounding the inclusion particle during the intermediate stage.Supported by the Inamori Foundation.     

Enhanced thermal stability of poly(lactide)s in the melt by enantiomeric polymer blending

Poly(l-lactide) (i.e. poly(l-lactic acid) (PLLA)) and poly(d-lactide) (i.e. poly(d-lactic acid) (PDLA)) and their equimolar enantiomeric blend (PLLA/PDLA) films were prepared and the effects of enantiomeric polymer blending on the thermal stability and degradation of the films were investigated isothermally and non-isothermally under nitrogen gas using thermogravimetry (TG). The enantiomeric polymer blending was found to successfully enhance the thermal stability of the PLLA/PDLA film compared with those of the pure PLLA and PDLA films. The activation energies for thermal degradation (ΔE_td) were evaluated at different weight loss values from TG data using the procedure recommended by MacCallum et al. The ΔE_td values of the PLLA/PDLA, PLLA, and PDLA films were in the range of 205-297, 77-132, and 155-242 kJ mol⁻¹ when they were evaluated at weight loss values of 25-90% and the ΔE_td value of the PLLA/PDLA film was higher by 82-110 kJ mol⁻¹ than the averaged ΔE_td value of the PLLA and PDLA films. The mechanism for the enhanced thermal stability of the PLLA/PDLA film is discussed.     

Effect of polymer density on polyethylene hollow fiber membrane formation via thermally induced phase separation

Microporous high‐density polyethylene (HDPE) and low‐density polyethylene (LDPE) hollow fiber membranes were prepared from polyethylene–diisodecyl phthalate solution via thermally induced phase separation. Effect of the polyethylene density on the membrane structure and performance was investigated. The HDPE membrane showed about five times higher water permeability than the LDPE membrane because it had the larger pore and the higher porosity at the outer membrane surface. The formation of the larger pore was owing to both the initial larger structure formed by spinodal decomposition and the suppression of the diluent evaporation from the outer membrane surface due to the higher solution viscosity. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 93: 471–474, 2004     

Studies on phase separation rate in porous polyimide membrane formation by immersion precipitation

Phase separation rate during porous membrane formation by immersion precipitation was investigated by light scattering in a polyimide/N‐Methylpyrrolidone (NMP)/water system. In the light scattering measurement, plots of scattered intensity against scattered angle showed maxima in all cases, which indicated that phase separation occurred by a spinodal decomposition (SD). Characteristic properties of the early stage of SD, such as an apparent diffusion coefficient D_app and an interphase periodic distance Λ, were obtained. The growth process of Λ was also followed by light scattering. The growth rate had the same tendency as D_app when water content in the nonsolvent bath and the polymer concentration in the cast solution were changed. The pore size of the final membrane increased with decreasing water content, which was opposite to the tendency of Λ growth rate. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 292–296, 2003     

A coaxial pulsed plasma thruster using chemical propellants

Pulsed plasma thrusters (PPTs) have the advantages of mechanical simplicity and robustness compared to other electric propulsion systems. However the thrust power ratio of PPTs is lower than that of other electric propulsion systems. To enhance the thrust performance of the PPT, we propose to use several combustible solid chemicals as coaxial PPT propellants to replace Teflon^® (Polytetrafluoroethylene: PTFE). With the design, the force obtained thermodynamically is expected to augment the PPT thrust power ratio with the help of the chemical energy contained in the propellants. As a result, the thrust power ratio is increased using hydroxyl-terminated polybutadiene-ammonium perchlorate (HTPB-AP)-based propellants compared to the case of ordinary Teflon. The discharge current and voltage waveform does not change even when the propellant is changed. These findings could indicate that the impulse bits by gasdynamic contribution are lager in the case of chemical solid propellants than in the case of Teflon.     

Macrophage Activation Markers Predict Liver-Related Complications in Primary Biliary Cholangitis

Primary biliary cholangitis (PBC) has a wide variation in clinical presentation and course. There is no significant correlation between these symptoms and the disease stage, although patients with more advanced stages generally have more symptoms. It is important to develop biomarkers in order to identify patients with an increased risk of complications and end-stage liver disease. This study investigated surrogate markers for risk estimation of PBC-related complications, including a study population of 77 patients with PBC who underwent liver biopsy and were measured for serum levels of macrophage activation markers, soluble CD163 (sCD163), soluble mannose receptor (sMR), and zonulin. Patients with PBC were divided into symptomatic (Group S, n = 20) and asymptomatic (Group A, n = 57) groups. The correlations of histological stages based on both Scheuer and Nakanuma classifications with the three serum markers were investigated. The Nakanuma classification involves grading for liver fibrosis and bile duct loss. The three biomarkers were assessed for their diagnostic ability to identify patients with PBC having high risk of developing complications. The predictive factors of these complications were examined as well. Group S had significantly higher serum sMR (p = 0.011) and sCD163 (p = 0.048) levels versus Group A. A composite index of sMR and sCD163 measurements had significantly better prediction performance than sCD163 alone (p = 0.012), although not when compared to sMR alone (p = 0.129). Serum sMR was an independent factor for developing complications on both univariate (Odds ratio (OR) = 30.20, 95% confidence interval (95% CI): 3.410–267.0, p = 0.00220), and multivariate (OR = 33.70, 95% CI: 3.6600–311.0, p = 0.0019) analyses. Patients with PBC having sMR of ≥56.6 had a higher incidence of clinical complications versus those with a sMR of <56.6. Serum sMR predicts the development of complications in patients with PBC. sMR plus sCD163 showed better predictive power than either marker alone, although the addition of sCD163 did not improve the predictive power of sMR. Future prospective studies are required in order to validate the findings of the present study.