Influence of the cross‐sectional shape on the structure and properties of polyester fibers

The effects of the fiber cross‐sectional shape on the structure and properties of polyester fibers were investigated. Fully drawn yarn (FDY) polyester fibers (167 dtex and 48 filaments) were produced under the same spinning conditions used in a spinning plant. The only difference between the fibers was their cross‐sectional shapes. Four different cross‐sectional shapes were chosen for the experimental work: round, hollow‐round, trilobal, and hollow‐trilobal. The crystallinity and values of the maximum stress, maximum strain, modulus, yield stress, shrinkage in boiling water, and unevenness of the fibers were determined. The difference in the cross‐sectional shapes influenced the modulus, maximum strain, yield stress, and shrinkage in boiling water. No effects on the crystallinity and maximum stress were observed. The results suggested that the hollow fibers had higher amorphous orientation than the full fibers. The hollow‐round fiber had the highest unevenness value. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 2615–2621, 2007     

Fusion of smartphone sensor data for classification of daily user activities

Multimedia Tools and Applications - New mobile applications need to estimate user activities by using sensor data provided by smart wearable devices and deliver context-aware solutions to users...     

Micro-milling performance of AISI 304 stainless steel using Taguchi method and fuzzy logic modelling

In this study, micro-milling of AISI 304 stainless steel with ball nose end mill was conducted using Taguchi method. The influences of spindle speed, feed rate and depth of cut on tool wear, cutting forces and surface roughness were examined. Taguchi’s signal to noise ratio was utilized to optimize the output responses. The influence of control parameters on output responses was determined by analysis of variance. In this study, the models describing the relationship between the independent variables and the dependent variables were also established by using regression and fuzzy logic. Efficiency of both models was determined by analyzing correlation coefficients and by comparing with experimental values. The results showed that both regression and fuzzy logic modelling could be efficiently utilized for the prediction of tool wear, cutting forces and surface roughness in micro-milling of AISI 304 stainless steel.     

Experimental and numerical studies on the determination of twist drill temperature in dry drilling: A new approach

In this paper, the influences of the spindle speed and feed rate on the drill temperature responses have been investigated. A new experimental approach was developed to measure drill temperature in drilling process. Drill temperatures were measured by inserting standard thermocouples through the coolant (oil) hole of TiAlN-coated carbide drills. Experimental parameters used in the study has based on Taguchi’s method. Experimental study was conducted by using two different workpiece materials, AISI 1040 steel and Al 7075-T651. The drill bit temperature was predicted using a numerical calculation with Third Wave AdvantEdge^TM Lagrangian based on explicit finite element analysis software. The results obtained from experimental study and finite element analyses (FEA) were compared. Good agreement between the measured and analyzed temperature results was found in dry drilling process.     

A stochastic MIMO channel model with joint correlation of both link ends

Abstract-This paper presents a novel stochastic channel model for multiple-input multiple-output (MIMO) wireless radio channels. In contrast to state-of-the-art stochastic MIMO channel models, the spatial correlation properties of the channel are not divided into separate contributions from transmitter and receiver. Instead, the joint correlation properties are modeled by describing the average coupling between the eigenmodes of the two link ends. The necessary and sufficient condition for the proposed model to hold is that the eigenbasis at the receiver is independent of the transmit weights, and vice versa. The authors discuss the mathematical elements of the model, which can be easily extracted from measurements, from a radio propagation point of view and explain the underlying assumption of the model in physical terms. The validation of the proposed model by means of measured data obtained from two completely different measurement campaigns reveals its ability to better predict capacity and spatial channel structure than other popular stochastic channel models.     

Mechanical,chemical, thermal,and rheological properties of recycled PA6/ABS binary and PA6/PA66/ABS ternary blends

The effects of multiple injection molding cycles on the chemical and mechanical properties of PA6/ABS and PA6/PA66/ABS blends are investigated. The chemical structures of both PA6/ABS binary and PA6/PA66/ABS ternary blends do not alter after recycling process. For PA6/ABS binary blend, it is found that the tensile strength, strain at break, elastic modulus, impact strength, flexural strength, and modulus of recycled blend decrease by 6.49%, 15.19%, 21.00%, 9.41%, 7.09%, and 8.25%, respectively, while MFI increases by 23.59% as compared with the virgin blend. After five recycling process for PA6/PA66/ABS ternary blend, the tensile strength, strain at break, and impact strength of recycled blend decrease by 18.00%, 50.80%, and 87.27%, respectively. However, flexural strength and modulus of PA6/PA66/ABS blend increase slightly. For virgin PA6/PA66/ABS blend, MFI value was 7.7 g/10 min and with recycling this value showed an important increase to 31.56 g/10 min after five cycles. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40810.     

Effects of Light, Oxygen, and pH on the Absorbance of 2,2-Diphenyl-1-picrylhydrazyl

ABSTRACT: The absorbance of 2,2-diphenyl-1-picrylhydrazyl (DPPH) at 517 nm in methanol and acetone decreased by 20 and 35% for 120 min at 25 °C under light, respectively; in the dark it did not change significantly for 150 min. Decomposition of DPPH under 21% oxygen after 90 min under light was significantly higher than that under 1% oxygen. Absorbance of DPPH in pH 4 buffer solution in methanol, and in pH 10 buffer solution in acetone, decreased by 55 and 80%, respectively, under light for 120 min. The evaluation of antioxidant activity by the changes of DPPH absorbance should be carefully interpreted since the absorbance of DPPH at 517 nm is decreased by light, oxygen, pH, and type of solvent in addition to the antioxidant.     

Effect of high valency cations on the (BiPb)2Sr2Ca3Cu4O12+δ compounds

We have produced the (BiPb)₂V _x Sr₂Ca₃Cu_4−y Ti _y O_12+δ compounds by a melt-quenching method. For two different sintering times (185 and 192 hours), the effects of vanadium adding and Ti doping on the structure have been investigated by electrical resistance, scanning electron micrographs (SEM), XRD patterns and magnetic hysteresis loop measurements. It has been found that the high-T _c superconducting phase, (2223), is formed in the samples annealed at 845 ^○C for 185 and 192 h, with concentration x=0.2 and y=0.05. However, with increasing Ti doping the (2223) phase gradually transforms into the (2212) phase. The hysteresis loop areas decrease with increasing Ti concentration and sintering time. Our data have indicated that the critical current, J _c , decreases with increasing magnetic field.     

The effect of recycling number on the mechanical,chemical, thermal,and rheological properties of PBT/PC/ABS ternary blends: With and without glass‐fiber

The recycling possibilities of poly(butylene terephthalate)/polycarbonate/acrylonitrile–butadiene–styrene (PBT/PC/ABS) ternary blend with and without glass‐fiber content were investigated using repeated injection molding process. In this study, PBT/PC/ABS ternary blends were reprocessed at five times and the results were presented after each recycling process. The recycling possibility of PBT/PC/ABS ternary blend was evaluated by measuring the mechanical, chemical, thermal, and rheological properties. Mechanical properties were determined by the tensile strength, yield strength, strain at break, elastic modulus, impact strength, flexural strength, and flexural modulus. Chemical and thermal properties were evaluated by Fourier transform infrared spectroscopy, differential scanning calorimetry, thermal gravimetric analysis, and scanning electron microscopy. Rheological properties of the ternary blends were studied by melt flow index measurement. From the results, it was found that mechanical properties of recycled composites were better than virgin PBT/PC/ABS ternary blends. POLYM. COMPOS., 35:2074–2084, 2014. © 2014 Society of Plastics Engineers     

Evaluating the in vitro bioaccessibility of phenolics and antioxidant activity during consumption of dried fruits with nuts

Dried fruits and nuts are considered as healthy snacks and they are often consumed together in the Turkish diet. In order to investigate the effect of codigestion of dried fruits (figs, apricots, raisins) together with nuts (almonds, walnuts, hazelnuts), total phenolics (TP) and total antioxidant capacity (TAC) have been evaluated spectrophotometrically at different phases of simulated gastrointestinal (GI) digestion, using an in vitro model. TP, ABTS and CUPRAC results revealed that for all fruit–nut mixtures, the amount recovered in the dialyzed fraction was lower than the recovery of fruits or nuts alone, indicating an antagonistic effect. On the other hand, DPPH results showed that for fig–walnut, fig–hazelnut and apricot–hazelnut mixtures the quantity recovered in the dialyzed fractions were 35–107% higher than the recovery of fruits or nuts alone, representing a synergistic effect. Similarly, FRAP results also demonstrated a synergistic effect in case of fig–walnut, apricot–walnut and apricot–hazelnut mixtures (10–74% higher recovery). Current study provides valuable insights into the changes taking place during in vitro GI digestion of dried fruits and nuts.