AFM observation of polyethylene single crystals: selective handedness of screw dislocations in a chair type

The three-dimensional morphology of polyethylene single crystals grown from dilute solution has been examined by atomic force microscopy. Single crystals were deposited on a soft ground of aqueous solution of poly(vinyl alcohol) (PVA) to avoid the collapse of thin lamellar crystals with thickness of 10 nm. The observation of single crystals on dried PVA clarifies the morphology of a chair type crystal as well as well-known hollow pyramidal type. It has been confirmed that the screw dislocations in the chair type follow a selection rule of the handedness in a manner to relieve the distortion in the chair type.     

Evaluation of inelastic constitutive models under plasticity-creep interaction for steel at 600°C

Uniaxial tests to identify plasticity-creep interaction in steel at 600°C were carried out as the Benchmark Project by the Subcommittee on Inelastic Analysis and Life Prediction, JSMS. The purpose of this paper is to present recent experimental data and predictions of constitutive models obtained in the project. Ten types of constitutive models were utilized to compare analytical predictions to sixteen benchmark experiments which are grouped into four categories: (I) tensile and creep tests under monotonic loading, (II) mixed mode tests under plastic and creep loading, (III) ratcheting deformation tests under program loads, and (IV) cyclic deformation tests under the combination of different strain rates. The benchmark tests in Group IV are used to estimate the creep-fatigue life of steel; the results will be published in a separate paper.     

Stabilization of inter-area and/or oscillatory modes in large-scale power system by voltage impedance power system (VIPS) apparatus based on decentralized control scheme

New technologies such as power electronics have made it possible to change continuously the impedance of a power system not only to control power flow but also to enhance stability. A power system incorporating a variable impedance apparatus such as a variable series capacitor (VSrC) and high-speed phase shifter (HSPS) is called VIPS (Variable Impedance Power System) by the authors. This paper proposes a novel control method of VIPS apparatus such as VSrC and HSPS installed at an interconnecting point for stabilizing inter-area unstable and/or oscillatory modes. The proposed design method of the control system is a kind of hierarchical decentralized control method of a large-scale power system based on a Lyapunov function. Under the proposed control scheme, each subsystem can be stabilized independently by local controllers such as AVR, speed governor and PSS, and then the whole interconnected system can be stabilized by VIPS apparatus taking into account interactions between subsystems. The effectiveness and robustness of the VIPS apparatus control are shown by numerical examples with model systems including a large-scale power system.     

Effect of surfactants on phenol removal by the method of polymerization and precipitation catalysed by Coprinus cinereus peroxidase

The removal of phenol by peroxidase‐catalysed polymerization was examined using Coprinus cinereus peroxidase in the presence of surfactants. The non‐ionic surfactants with poly(oxyethene) residues, Triton X‐100, Triton X‐405 and Tween 20, enhanced the phenol removal efficiency at a level similar to high relative molecular mass poly(ethylene glycol) (relative molecular mass 3000). Although the improvement in the removal efficiency was less than that of Triton X‐100, Span 20, sodium lauryl sulfate (SDS) and lauryl trimethylammonium bromide (DTAB) also enhanced the removal efficiency. The requirement of the enzyme for almost 100% removal of 100 mg dm^?3 phenol decreased to one‐fourth by the addition of 30 mg dm^?3 Triton X‐100. Triton X‐100, Triton X‐405, Tween 20 and DTAB could reactivate the enzyme precipitated with the phenol polymer, leading to the restarting of the phenol removal reaction. Copyright © 2003 Society of Chemical Industry     

Damage tolerance of glass mat/epoxy laminates hybridized with flexible resin under static and impact loading

This study deals with the impact property and damage tolerance of matrix hybrid composite laminates with different laminate constitution. The matrix hybrid composite laminates consisted of the laminae with a conventional epoxy resin and the laminae with a flexible epoxy resin modified from the conventional resin to avoid the interlaminar delamination. The impact energy absorption ratio greatly depended on the matrix resin placed at the impact face. The energy absorption was almost constant if the conventional resin was placed at the impact surface layer, while it increased exponentially with the increasing fraction of the flexible resin if the flexible resin was placed at the impact face. The impact energy was absorbed by the damage development and propagation in the laminate with conventional resin laminae as the impacted face, while it was absorbed by both the recoverable deformation of the flexible resin and the damage propagation in the laminate with flexible resin laminae as the impacted face.     

Syntheses and structural properties of four Rb-aluminosilicate zeolites

Four types of Rb-aluminosilicate zeolites were hydrothermally synthesized in pure phase for the first time from Rb-aluminosilicate gels without using any organic structure-directing agent (SDA) under stirring conditions. The crystal structure of each zeolite was refined by Rietveld analysis of the X-ray diffraction (XRD) data. These crystal structures were confirmed to be Rb-mordenite, Rb-merlinoite, a new aluminosilicate zeolite with an ATT framework topology, and Rb-offretite denoted by RMA-1, RMA-2, RMA-3, and RMA-4, respectively. The Si/Al ratio of RMA-1 with an MOR topology varied from 5.3 to 8.0; however, the variation of the Si/Al ratios of the other zeolites was rather small. The crystal system of RMA-2 was tetragonal with space group I4/mmm, where two Rb sites were distributed at the center of an 8-membered ring (MR). On the other hand, two Rb sites in RMA-3 were located at the center of the 8-MR in small two cages. The structure of RMA-4 was identified as the OFF type with a local disorder or defect, which included a small amount of an intergrown ERI phase.     

Novel Constitutive Equation for Predicting Dynamic Recrystallization During Hot Working Considering the Efficiency of Power Dissipation

The efficiency of power dissipation (η) in a dynamic material model has been conventionally used for qualitative predictions to estimate the hot working conditions at which dynamic recrystallization (DRX) is dominant. However, predicting the quantitative value of the DRX fraction (X_DRX) from η remains a challenge. In this paper, a constitutive equation is proposed to quantitatively predict X_DRX using η. The proposed equation for describing X_DRX is derived from the reaction rate equation using the assumption that the DRX rate depends on η. The proposed equation is verified via hot compression tests of equiaxed Ti–6Al–4V ELI alloys (Ti-64) in the (α + β) region. The predicted and experimental X_DRX values are found to be generally consistent with one another, exhibiting an average absolute error of 0.05. Furthermore, the proposed equation provides the same level of prediction accuracy as the conventional Johnson–Mehl–Avrami–Kolmogorov (JMAK) equation. Therefore, the proposed equation can be used to quantitatively predict X_DRX following hot compression tests of equiaxed Ti-64. Moreover, compared with the JMAK equation, the proposed equation is expressed in fewer parameters and constant terms. It is, thus, expected to facilitate the quantitative prediction of X_DRX.

     

Effect of Silicon Dioxide on the Thermal Diffusivity of Aluminum Nitride Ceramics

The thermal diffusivity of AlN ceramics was significantly decreased by the addition of SiO₂. The AlN ceramics with 4 wt% SiO₂ could not be densified by pressureless sintering in the temperature range 1400° to 1800°C. The thermal diffusivity of these samples was very low because of their porous structure. The AlN ceramics containing 2, 4, and 8 wt% SiO₂ were densified by hot-pressing and also had low thermal diffusivity. In these samples, the grains of the 27R polytype that resulted from the reaction between AlN and SiO₂ were dispersed, obstructing the conduction of heat. The relation between the amount of 27R polytype and the thermal diffusivity of the AlN ceramics was determined.     

Protective effect of phytic acid hydrolysis products on iron-induced lipid peroxidation of liposomal membranes

Beneficial effects of dietary phytic acid (myo-inositol hexaphosphate; IP₆) have often been explained by its strong iron ion-chelating ability, which possibly suppresses iron ion-induced oxidative damage in the gastrointestinal tract. Because phytic acid is hydrolyzed during digestion, this work aimed to know whether its hydrolysis products (IP_2′ IP_3′, IP_4′ and IP₅) could still prevent iron ion-induced lipid peroxidation. Studies using liposomal membranes demonstrated that hydrolysis products containing three or more phosphate groups are able to inhibit iron ion-induced lipid peroxidation although their effectiveness decreased with dephosphorylation. Similarly, they also prevented iron ion-induced decomposition of phosphatidylcholine hydroperoxide. These results demonstrate that intermediate products of phytic acid hydrolysis still possess iron ion-chelating ability, and thus they can probably prevent iron ion-induced lipid peroxidation in biological systems.     

Photocatalytic H2 evolution under visible light irradiation on Zn1-x Cu x S solid solution

The H₂ evolution reaction from an aqueous Na₂SO₃ solution proceeded with 3.7% quantum yield under visible light irradiation (λ > 420 nm) on a Zn_0.957Cu_0.043S solid solution photocatalyst without co‐catalysts such as Pt. This revised version was published online in July 2006 with corrections to the Cover Date.