KINETICS FOR LOW TEMPERATURE PYROLYSIS OF BLACK LIQUOR

A kinetic study of pyrolysis of dried black liquor was performed using a Netzsch 429 Thermogravimetric Analyzer. It was found that as conversion increases from 10 to 45% the apparent pyrolysis activation energy for black liquor increases from 77.20 to 112.74 KJ/mol. For black liquor the order of reaction was found to be first-order. The reaction rate constant was found to be 2.12×10⁹ min. These results are in agreement with the data reported by other investigators on biomass pyrolysis.     

Rheumatic heart disease in India

A cross-sectional study was carried out in rural areas of Jawan Block, District Aligarh, Uttar Pradesh, India, covering a total population of 3760 drawn from 11 villages. The total number of confirmed cases of rheumatic heart disease was 24 with a prevalence rate of 6.4 per 1000 of the general rural population. The prevalence of rheumatic heart disease increased with age until the age of 25 years. Females were more prone to rheumatic heart disease compared to males. Socio-economic class had a direct impact on the occurrence of rheumatic heart disease.     

A comprehensive study on RF MEMS switch

This paper emphasis on state-of-the-art of the earlier until the current trend and demand, principles, design considerations, key performance and fabrication technology of RF MEMS switch devices developed over the past few years. RF MEMS switch performance and features such as actuation voltage, insertion loss, isolation and ease with cost of fabrication and applications are compared and discussed.     

Graft Copolymerization of Acrylamide onto Oil Palm Empty Fruit Bunch (OPEFB) Fiber

Grafting of acrylamide (AAm) onto oil palm empty fruits bunch fiber using hydrogen peroxide as initiator and methyl acrylate as comonomer was investigated. The amount of comonomer needed to make grafting of acrylamide possible was determined. The percentage of poly(acrylamide) and the comonomer in the final graft copolymer was estimated by elemental analysis. Results obtained indicated that methyl acrylate facilitated the incorporation of acrylamide monomer onto OPEFB. The reactivity ratios for both monomers were determined by using Fineman–Ross plot. The effects of reaction temperature and period as well as amount of the initiator, solvent, monomer and comonomer on the percentage of grafting at fixed amount of comonomer (11 mmol) were studied. Maximum percentage of grafting was achieved when the amount of initiator and solvent 3.98×10⁻³ mol and 50 mL respectively. The optimum reaction temperature was 50 ^○C and the reaction period was 90 min. Highest percentage of grafting was 232% when 25.6 mmol of acrylamide was used under these optimum conditions. The presence of functional group in the grafted polymer is characterized by infrared spectroscopy and the surface morphology is observed by scanning electron microscopy. Thermoanalytic investigation on OPEFB and OPEFB-g-PAAM were carried out to evaluate the thermal stability and respective activation energy of the materials.     

Mullite for Structural, Electronic, and Optical Applications

Mullite (3Al₂O₃·2SiO₂) is becoming increasingly important in electronic, optical, and high-temperature structural applications. This paper reviews the current state of mullite-related research at a fundamental level, within the framework of phase equilibria, crystal structure, synthesis, processing, and properties. Phase equilibria are discussed in terms of the problems associated with the nucleation kinetics of mullite and the large variations observed in the solid-solution range. The incongruent melting behavior of mullite is now widely accepted. Large variations in the solid solubility from 58 to 76 mol% alumina are related to the ordering/disordering of oxygen vacancies and are strongly coupled with the method of synthesis used to form mullite. Similarly, reaction sequences which lead to the formation of mullite upon heating depend on the spatial scale at which the components are mixed. Mixing at the atomic level is useful for low-temperature (<1000°C) synthesis of mullite but not for low-temperature sintering. In contrast, precursors that are segregated are better suited for low-temperature (1250° to 1500°C) densification through viscous deformation. Flexural strength and creep resistance at elevated temperatures are significantly affected by the presence of glassy boundary inclusions; in the absence of glassy inclusions, polycrystalline mullite retains >90% of its room-temperature strength to 1500°C and displays very high creep resistance. Because of its low dielectric constant, mullite has now emerged as a substrate material in high-performance packaging applications. Interest in optical applications mainly centers on its applicability as a window material within the mid-infrared range.     

Prosthetic Hand Finger Control Using Fuzzy Sliding Modes

In order to improve the life quality of amputees, providing approximate manipulation ability of a human hand to that of a prosthetic hand is considered by many researchers. In this study, a biomechanical model of the index finger of the human hand is developed based on the human anatomy. Since the activation of finger bones are carried out by tendons, a tendon configuration of the index finger is introduced and used in the model to imitate the human hand characteristics and functionality. Then, fuzzy sliding mode control where the slope of the sliding surface is tuned by a fuzzy logic unit is proposed and applied to have the finger model to follow a certain trajectory. The trajectory of the finger model, which mimics the motion characteristics of the human hand, is pre-determined from the camera images of a real hand during closing and opening motion. Also, in order to check the robust behaviour of the controller, an unexpected joint friction is induced on the prosthetic finger on its way. Finally, the resultant prosthetic finger motion and the tendon forces produced are given and results are discussed.     

A new method of reinforcing graphene nanoplatelets in glass/epoxy composites

This research aims to develop a method for the amalgamation of graphene nanoplatelets in glass/epoxy composites. The poor interface bonding between the fiber and matrix is critical and hinders the full performance of the composites. Glass fabric and epoxy were used as reinforcement and matrix in the composite, respectively. Graphene nanoplatelets were utilized as an additional nano-materials filler for the composites. Glass/graphene/epoxy and glass/epoxy composites were fabricated via vacuum infusion molding. The new method of applying graphene nanoplatelets as secondary reinforcement in the composite was developed based on proper functionalization in the sonication process. The physical, tensile, flexural, and short beam interlaminar properties of fabricated composites were examined to analyze the method's effectiveness. The results showed that density decreased by around 5 %; however, thickness increased by around 34 % after introducing graphene nanoplatelets into the composites. The tensile strength and modulus of the composites declined by approximately 19 %, on the other hand, flexural strength and modulus increased by around 63.3 % and 8.3 %, respectively, after the addition of graphene nanoplatelets into the composites. Moreover, interlaminar shear strength of the composite was enhanced by approximately 50 %.     

Visualizing Co‐occurrence of Events in Populations of Viral Genome Sequences

Virologists are not only interested in point mutations in a genome, but also in relationships between mutations. In this work, we present a design study to support the discovery of correlated mutation events (called co‐occurrences) in populations of viral genomes. The key challenge is to identify potentially interesting pairs of events within the vast space of event combinations. In our work, we identify analyst requirements and develop a prototype through a participatory process. The key ideas of our approach are to use interest metrics to create dynamic filtering that guides the viewer to interesting and relevant correlations of genome mutations, and to provide visual encodings designed to fit scientists' mental map of the data, along with dynamic filtering techniques. We demonstrate the strength of our approach in virology‐situated case studies, and offer suggestions for extending our strategy to other sequence‐based domains.     

Fabrication of circular microfluidic channels through grayscale dual-projection lithography

Circular microfluidic channels are in great demand since they are more realistic in mimicking physiological flow systems, generating axis-symmetrical flow, and achieving uniform shear stress. A typical microchannel with rectangular cross section can induce non-physiological gradients of shear rate, pressure, and velocity. This paper presents a novel method of fabricating microfluidic channels with circular and elliptical cross sections through grayscale dual-projection lithography. Our method utilizes two projecting systems to expose grayscale image face-to-face and simultaneously polymerize the photocurable material. The cross-sectional profiles of the fabricated microchannels are consistent with mathematical predictions and, therefore, demonstrate the capability of controlling the channel shapes precisely. Customized circular microchannels can be generated with complex features such as junctions, bifurcations, hierarchies, and gradually changed diameters. This method is capable of fabricating circular channels with a wide range of diameters (39 μm–2 mm) as well as elliptical channels with a major-to-minor axis ratio up to 600%. Microfluidic devices with circular cross sections suitable for particle analysis were made as a demonstrative application in nanoparticle binding and distribution within a mimetic blood vessel. A ready-to-use microfluidic device with customized circular channels can be fabricated within 1 h without the need of clean room or expensive photolithography devices.