Formability of a high-strength Al–Mg6.8 type alloy sheet

Room temperature formability testing was performed on an AlMg6.8 type alloy sheet with a fully recrystallized structure (average grain diameter 18 m) and after partial annealing with a retained deformed structure. The yield strengths attained after full recrystallization and after partial annealing, were 175 and 283 MPa respectively. Such an increase in strength is followed by formability degradation, maximized around the plain strain state to either 42%, as obtained using the limiting dome height test (LDH), or 35% after using forming limit curves (FLC). A comparison with known high-strength formable alloys has shown that the tested alloy in the recrystallized condition has a better stretch formability (at the same or even higher yield stress level), while in the unrecrystallized-partially annealed condition it has a lower formability, limiting its application to moderate forming requirements for very high-strength parts. © 1998 Chapman & Hall     

Controlled linear perturbation

We present an algorithmic solution to the robustness problem in computational geometry, called controlled linear perturbation, and demonstrate it on Minkowski sums of polyhedra. The robustness problem is how to implement real RAM algorithms accurately and efficiently using computer arithmetic. Approximate computation in floating point arithmetic is efficient but can assign incorrect signs to geometric predicates, which can cause combinatorial errors in the algorithm output. We make approximate computation accurate by performing small input perturbations, which we compute using differential calculus. This strategy supports fast, accurate Minkowski sum computation. The only prior robust implementation uses a less efficient algorithm, requires exact algebraic computation, and is far slower based on our extensive testing.     

Prediction of Functional Consequences of Missense Mutations in ANO4 Gene

The anoctamin (TMEM16) family of transmembrane protein consists of ten members in vertebrates, which act as Ca²⁺-dependent ion channels and/or Ca²⁺-dependent scramblases. ANO4 which is primarily expressed in the CNS and certain endocrine glands, has been associated with various neuronal disorders. Therefore, we focused our study on prioritizing missense mutations that are assumed to alter the structure and stability of ANO4 protein. We employed a wide array of evolution and structure based in silico prediction methods to identify potentially deleterious missense mutations in the ANO4 gene. Identified pathogenic mutations were then mapped to the modeled human ANO4 structure and the effects of missense mutations were studied on the atomic level using molecular dynamics simulations. Our data show that the G80A and A500T mutations significantly alter the stability of the mutant proteins, thus providing new perspective on the role of missense mutations in ANO4 gene. Results obtained in this study may help to identify disease associated mutations which affect ANO4 protein structure and function and might facilitate future functional characterization of ANO4.     

Hydrodesulfurization of Diesel Feeds by Association of a Catalytic Process and a Separation Process Using Charge-Transfer Complexes

While deep hydrodesulfurization of gas oil is more and more important, elimination of sulfur compounds such as 4,6-dialkyldibenzothio-phenes still attracts considerable attention. A new process based on the association of a separation process by charge-transfer complex (CTC) formation and classical catalytic hydrotreating (HDT) was evaluated. The results indicated that a CTC pretreatment allows the rate of hydrodesulfurization (HDS) to increase and the final sulfur level to decrease. This process is even more efficient for feeds difficult to desulfurize.     

Weighted Superimposed Codes and Constrained Integer Compressed Sensing

We introduce a new family of codes, termed weighted superimposed codes (WSCs). This family generalizes the class of Euclidean superimposed codes (ESCs), used in multiuser identification systems. WSCs allow for discriminating all bounded, integer-valued linear combinations of real-valued codewords that satisfy prescribed norm and nonnegativity constraints. By design, WSCs are inherently noise tolerant. Therefore, these codes can be seen as special instances of robust compressed sensing schemes. The main results of the paper are lower and upper bounds on the largest achievable code rates of several classes of WSCs. These bounds suggest that, with the codeword and weighting vector constraints at hand, one can improve the code rates achievable by standard compressive sensing techniques.     

Generalized low-density parity-check codes for optical communication systems

This paper is concerned with investigating the performance of regular and irregular, randomlike and structured generalized low-density parity-check (GLDPC) codes for long-haul transmission. The proposed GLDPC codes outperform currently known turbo and low-density parity-check (LDPC) coding schemes with comparable parameters utilized in optical communication systems. For a GLDPC coding scheme with 23.6% redundancy, the largest so far reported coding gain of at least 11dB (at 40 Gb/s) is demonstrated.     

Sequential SO2/CO2 capture enhanced by steam reactivation of a CaO-based sorbent

The steam hydration reactivation characteristics of three limestone samples after multiple CO₂ looping cycles are presented here. The CO₂ cycles were performed in a tube furnace (TF) and the resulting samples were hydrated by steam in a pressure reactor (PR). The reactivation was performed with spent samples after carbonation and calcination stages. The reactivation tests were done with a saturated steam pressure at 200 °C and also at atmospheric pressure and 100 °C. The characteristics of the reactivation samples were examined using BET and BJH pore characterization (for the original and spent samples, and samples reactivated under different conditions) and also by means of a thermogravimetric analyzer (TGA). The levels of hydration achieved by the reactivated samples were determined as well as the conversions during sulphation and multiple carbonation cycles. It was found that the presence of a CaCO₃ layer strongly hinders sorbent hydration and adversely affects the properties of the reactivated sorbent with regard to its behavior in sulphation and multiple carbonation cycles. Here, hydration of calcined samples under pressure is the most effective method to produce superior sulphur sorbents. However, reactivation of calcined samples under atmospheric conditions also produces sorbents with significantly better properties in comparison to those of the original sorbents. These results show that separate CO₂ capture and SO₂ retention in fluidized bed systems enhanced by steam reactivation is promising even for atmospheric conditions if the material for hydration is taken from the calciner.     

Influence of calcination conditions on carrying capacity of CaO-based sorbent in CO2 looping cycles

This study examines the loss of sorbent activity caused by sintering under realistic CO₂ capture cycle conditions. The samples tested here included two limestones: Havelock limestone from Canada (New Brunswick) and a Polish (Upper Silesia) limestone (Katowice). Samples were prepared both in a thermogravimetric analyzer (TGA) and a tube furnace (TF). Two calcination conditions were employed: in N₂ at lower temperature; and in CO₂ at high temperature. The samples obtained were observed with a scanning electron microscope (SEM) and surface compositions of the resulting materials were analyzed by the energy dispersive X-ray (EDX) method. The quantitative influence of calcination conditions was examined by nitrogen adsorption/desorption tests, gas displacement pycnometry and powder displacement pycnometry; BET surface areas, BJH pore volume distributions, skeletal densities and envelope densities were determined. The SEM images showed noticeably larger CaO sub-grains were produced by calcination in CO₂ during numerous cycles than those seen with calcination in nitrogen. The EDX elemental analyses showed a strong influence of impurities on local melting at the sorbent particle surface, which became more pronounced at higher temperature. Results of BET/BJH testing clearly support these findings on the effect of calcination/cycling conditions on sorbent morphology. Envelope density measurements showed that particles displayed densification upon cycling and that particles calcined under CO₂ showed greater densification than those calcined under N₂. Interestingly, the Katowice limestone calcined/cycled at higher temperature in CO₂ showed an increase of activity for cycles involving calcination under N₂ in the TGA. These results clearly demonstrate that, in future development of CaO-based CO₂ looping cycle technology, more attention should be paid to loss of sorbent activity caused by realistic calcination conditions and the presence of impurities originating from fuel ash and/or limestone.