Discrete modeling of sand–tire mixture considering grain-scale deformability

Mixing sand or soil with small pieces of tire is common practice in civil engineering applications. Although the properties of the soil are changed, it is environmentally friendly and sometimes economical. Nevertheless, the mechanical behavior of such mixtures is still not fully understood and more numerical investigations are required. This paper presents a novel approach for the modeling of sand–tire mixtures based on the discrete element method. The sand grains are represented by rigid agglomerates whereas the tire grains are represented by deformable agglomerates. The approach considers both grain shape and deformability. The micromechanical parameters of the contact law are calibrated based on experimental results from the literature. The effects of tire content and confining pressure on the stress–strain response are investigated in detail by performing numerical triaxial compression tests. The main results indicate that both strength and stiffness of the samples decrease with increasing tire content. A tire contact of 40% is identified as the boundary between rubber-like and sand-like behavior.     

Performance Comparison of Four Fiber-Reinforced Polymer Deck Panels

In an effort to assess the constructability and performance of bridges with fiber-reinforced polymer (FRP) composite decks, the short-term and long-term responses of a 207 m, five-span bridge retrofitted with four different FRP panel systems were monitored. The overall aspects of the panel systems, connection details, and construction techniques are presented prior to presentation of the observed and measured responses. Key design parameters (impact factors, girder distribution factors, and level of composite action) for FRP and reinforced concrete decks are evaluated. This paper demonstrates that FRP replacement decks are a viable alternative to reinforced concrete decks and identifies the differences in performances of various FRP deck systems. Two of the FRP panel systems were found to perform considerably better than the other deck systems. Issues that may reduce the service life of FRP deck systems are presented and discussed.     

A Sliding Mode Controller Based on Robust Model Reference Adaptive Proportional-integral Control for Stand-alone Three-phase Inverter

This paper proposes a sliding mode controller based on robust model reference adaptive proportional-integral (RMRA-PI) control for a stand-alone voltage source inverter (SA-VSI). The proposed controller has two control loops where the coefficients of PI controller are regulated by the adaptive sliding law. This method is used to regulate the output voltage of the inverter under different load conditions and uncertainty, and adapts the output to the reference model to reduce the total harmonic distortion (THD). In this paper, the stability of the proposed controller is proven by using Lyapunov’s theory and Barbalet’s lemma. The proposed controller performs well in voltage regulation such as low THD under sudden load change and uncertainty. Also, the results of the proposed controller are compared with PI controller to show the effectiveness of the presented control system.     

The effect of microencapsulation with nitrocellulose on thermal properties of sodium azide particles

Based on the coacervation principle a solvent/non-solvent method has been used for microencapsulation of sodium azide (NaN₃) with fibrous nitrocellulose (NC). Scanning electron microscopy (SEM) was employed to examine the coating morphology. The thermal behavior of solid samples has been studied by means of thermogravimetry (TG) and differential scanning calorimetry (DSC). The results of TG–DTA analysis revealed that the main thermal degradation for the pure NC and NaN₃ occurs in the temperature ranges of 192–220 and 415–420 °C, respectively. The effects of some parameters, such as NC to NaN₃ weight ratio and volume and addition time of non-solvent, on coating quality and thermal properties have been investigated by SEM and thermal methods. The results of these experiments showed that the decomposition temperature of most stabilized coated sodium azide is about 50 °C higher than that of the pure sample. The DSC experiments were conducted to study the influence of the heating rate (5, 10, 15 and 20 °C/min) on the thermal decomposition processes of the pure NC, coated and pure NaN₃ samples. The results revealed that, as the heating rate was increased, decomposition temperature of the compounds was increased. Also, the kinetic parameters such as activation energy and frequency factor of the decomposition processes were obtained from the DSC data by non-isothermal methods proposed by ASTM E696 and Ozawa. Our finding showed that coated NaN₃ has lower decomposition rate with respect to the pure one.     

Characterization of minocycline loaded chitosan/polyethylene glycol/glycerol blend films as antibacterial wound dressings

Wound care has been a challenging subject for medical teams and researchers. Bacterial infections are one of the most serious complications in injured skins that often affect healing process. Antibacterial wound dressings can be used to facilitate wound healing process. The purpose of this study is to fabricate chitosan (Chito)/polyethylene glycol (PEG) antibacterial wound dressing doped with minocycline, and to evaluate the influence of composition ratio on the blending properties of the films. To improve the mechanical properties of these films, we examined various amounts of glycerol as a plasticizer. Moreover, we investigated morphological and mechanical aspects, water uptake, degradation, water vapor transmission and wettability properties of the films prepared with various ratios of Chito/PEG/Gly. Assessment of mechanical properties revealed that film containing 80:20 ratio Chito/PEG with 40 PHR Gly content exhibits the highest ultimate tensile strength and elongation at break (9.74 MPa and 45.73% respectively). Furthermore, results demonstrated that upon increasing PEG and Gly contents, degradability and hydrophilicity of the films increased whereas water uptake decreased. Water vapor transmission rate of the films was close to the range of 530–1200 g/m²d, indicating that the as formed films are possible candidates for dressing low exudate wounds or burns. Minocycline loaded films exhibited a biphasic drug release profile and it was more effective on gram-positive bacteria than on gram-negative bacteria. The polymeric film with the highest amount of loaded drug (2%) exhibited insignificant cytotoxicity (88%) against normal fibroblast cell line.     

CEDAR: Modeling impact of component error derating and read frequency on system-level vulnerability in high-performance processors

Reliability of the current microprocessor technology is seriously challenged by radiation-induced soft errors. Accurate Vulnerability Factor (VF) modeling of system components is crucial in designing cost-effective protection schemes in high-performance processors. Although Statistical Fault Injection (SFI) techniques can be used to provide relatively accurate VF estimations, they are often very time-consuming. Unlike SFI techniques, recently proposed analytical models can be used to compute VF in a timely fashion. However, VFs computed by such models are inaccurate as the system-level impact of soft errors is overlooked.     

On the mean residual lifetime of?consecutive k-out-of-n systems

In recent years, consecutive systems were shown to have many applications in various branches of science such as engineering. This paper is a study on the stochastic and aging properties of residual lifetime of consecutive k-out-of-n systems under the condition that n−r+1, r≤n, components of the system are working at time t. We consider the linear and circular consecutive k-out-of-n systems and propose a mean residual lifetime (MRL) for such systems. Several properties of the proposed MRL is investigated. The mixture representation of the MRL of the systems with respect to the vector of signatures of the system is also studied.     

Control of Hybrid Active Power Filter Based on Switching Function Coefficients

A pulse width modulation (PWM)-based control method for a three-level, four-wire neutral point clamped (NPC) inverter employed in a hybrid active power filter (HAPF) is proposed in this paper. The control method is based on switching function coefficients (SFCs) for harmonic compensation. An interior loop is also proposed for control and balancing of the DC-link voltages. In the proposed control system, one carrier signal is employed in the PWM unit in order to simplify its hardware as compared with traditional PWMs. Based on Fourier decomposition technique, mathematical analysis of the proposed control method is also presented. To decrease the NPC inverter rated power, passive power filters (PPFs) are designed to eliminate fifth and seventh order harmonic currents and to compensate source reactive currents. The proposed control system is implemented by a digital signal processing (DSP) in a laboratory prototype. The experimental results confirmed the validity of the proposed control method in compensation of harmonic currents under non-linear conditions     

Application of mesoporous magnetic carbon composite for reactive dyes removal: Process optimization using response surface methodology

Discharging the effluents of textile wastewaters into potable water resources can endanger the ecosystem, due to their reactivity, toxicity, and chemical stability. In this research, the application of powder activated carbon modified with magnetite nanoparticles (PAC-MNPs) as an adsorbent for removal of reactive dyes (Reactive black 5 (RB5) and reactive red 120 (RR120)) was studied in a batch system. The adsorption performance was evaluated as a function of temperature, contact time and different adsorbent and adsorbate concentrations. The levels of factors were statistically optimized using Box-Behnken Design (BBD) from the response surface methodology (RSM) to maximize the efficiency of the system. The adsorption process of both dyes was fit with the pseudo-second order kinetic and Langmuir isotherm models. The identified optimum conditions of adsorption were 38.7 °C, 46.3 min, 0.8 g/L and 102 mg/L for temperature, contact time, adsorbent dose, and initial dyes concentration, respectively. According to the Langmuir isotherm, the maximum sorption capacities of 175.4 and 172.4 mg/g were obtained for RB5 and RR120, respectively. Thermodynamics studies indicated that the adsorption process of the reactive dyes was spontaneous, feasible, and endothermic. After five cycles, the adsorption efficiency was around 84 and 83% for RB5 and RR120, respectively. A high value of desorption was achieved, suggesting that the PAC-MNPs have a good potential in regeneration and reusability, and also can be effectively utilized in industrial applications. PAC-MNPs also show a good anti-interference potential for removal of reactive dyes in dye-industry wastewaters.