Influence of melt temperature on Rapid solidification of Al-Y and Al-Si alloy system

Solidification behavior of Al-Y and Al-Si were investigated for different melt temperatures. Levitation casting technique was used to achieve a cooling rate of around ～2000K/s during the experiment. Light optical microscopy (LOM) and Scanning electron microscopy (SEM) were used to analyze the samples. An energy dispersive system (EDS) analysis of SEM was performed on the samples to identify the phases. Plate like structure of Al₈Y₃ primary phase was observed at low melt temperature with small percentage of peritectic transformation of Al₈Y₃ and liquid melt into Al₉Y₂. A pre-dentritic star like crystal of Al₃Y was observed in a fine eutectic matrix at very high melt temperature. Amount and number of primary Si crystals formed in a unit area during the solidification increases as the melt temperature increases. It is believed the melt temperature affects the solidification pattern by changing chemical short range order.     

The structural characterization of (NH4)2B10H10 and thermal decomposition studies of (NH4)2B10H10 and (NH4)2B12H12

The structure of (NH₄)₂B₁₀H₁₀ (1) was determined through powder XRD analysis. The thermal decomposition of 1 and (NH₄)₂B₁₂H₁₂ (2) was examined between 20 and 1000 °C using STMBMS methods. Between 200 and 400 °C a mixture of NH₃ and H₂ evolves from both compounds; above 400 °C only H₂ evolves. The dihydrogen bonding interaction in 1 is much stronger than that in 2. The stronger dihydrogen bond in 1 resulted in a significant reduction by up to 60 °C, but with a corresponding 25% decrease in the yield of H₂ in the lower temperature region and a doubling of the yield of NH₃. The decomposition of 1 follows a lower temperature exothermic reaction pathway that yields substantially more NH₃ than the higher temperature endothermic pathway of 2. Heating of 1 at 250 °C resulted in partial conversion of B₁₀H₁₀²⁻ to B₁₂H₁₂²⁻. Both 1 and 2 form an insoluble polymeric material after decomposition. The elements of the reaction network that control the release of H₂ from the B₁₀H₁₀²⁻ can be altered by conducting the experiment under conditions in which pressures of NH₃ and H₂ are either near, or away from, their equilibrium values.     

Effect of bundling on the π plasmon energy in sub-nanometer single wall carbon nanotubes

Due to their unusual electronic and vibrational properties, single walled carbon nanotubes (SWCNTs) with sub-nanometer diameters d ∼ 0.5–0.9 nm have recently gained interest in the carbon community. Using UV–Vis–NIR spectroscopy and ultra-centrifugation, we have conducted a detailed study of the π plasmon energy (present at∼5–7 eV) in sub-nm SWCNTs as a function of the size of the bundle. We find that the energy of the π plasmon peak E varies with the bundle diameter D_h as E = (-0.023 eV)^∗ln(D_h/d_o) + 5.37 eV, where d_o = 0.5 nm and corresponds to the smallest tube diameter.¹ This is compared with the same data for HiPCo and Carbolex SWCNTs of larger diameter (1–1.4 nm) confirming a clear dependence of E on the bundle size, which is present in addition to the previously reported dependence of E on SWCNT diameter d.     

A Novel Coverage Improved Deployment Strategy for Wireless Sensor Network

Coverage of the bounded region gets importance in Wireless Sensor Network (WSN). Area coverage is based on effective surface coverage with a minimum number of sensor nodes. Most of the researchers contemplate the coverage region of interest as a square and manifest the radio ranges as a circle. The area of a circle is much higher than the area of a square because of the perimeter. To utilize the advantage of the circle, the coverage region of interest is presumed as a circle for sensor node deployment. This paper proposes a novel coverage improved disc shape deployment strategy. Comparative analysis has been observed between circle and square regions of interest based on the cumulative number of sensor nodes required to cover the entire region. A new strategy named as disc shape deployment strategy is also proposed. Traditional hexagon and strip-based deployment strategies are compared with the disc shape deployment strategy. The simulation result shows that the circle shape coverage region of interest extremely reduces the required number of sensor nodes. The proposed deployment strategy provides desirable coverage, and it requires few more sensor nodes than hexagon shape deployment strategy.

     

Development of Nitrendipine Controlled Release Formulations Based on SLN and NLC for Topical Delivery: In Vitro and Ex Vivo Characterization

The aim of the investigation is to develop solid lipid nanoparticles (SLN) and nano-structured lipid carrier (NLC) as carriers for topical delivery of nitrendipine (NDP). NDP-loaded SLN and NLC were prepared by hot homogenization technique followed by sonication, and they were characterized for particle size, zeta potential, entrapment efficiency, stability, and in vitro release profiles. Also the percutaneous permeation of NDPSLN A, NDPSLN B, and NDPNLC were investigated in abdominal rat skin using modified Franz diffusion cells. The steady state flux, permeation coefficient, and lag time of NDP were estimated over 24 h and compared with that of control (NDP solution). The particle size was analyzed by photon correlation spectroscopy (PCS) using Malvern zeta sizer, which shows that the NDPSLN A, NDPSLN B, and NDPNLC were in the range of 124–300 nm during 90 days of storage at room temperature. For all the tested formulations (NDPSLN A, NDPSLN B, and NDPNLC), the entrapment efficiency was higher than 75% after 90 days of storage. The cumulative percentage of drug release at 24 h was found to be 26.21, 30.81, and 37.52 for NDPSLN A, NDPSLN B, and NDPNLC, respectively. The results obtained from in vitro release profiles also indicated the use of these lipid nanoparticles as modified release formulations for lipophilic drug over a period of 24 h. The data obtained from in vitro release from NDPSLN A, NDPSLN B, and NDPNLC were fitted to various kinetic models. High correlation was obtained in Higuchi and Weibull model. The release pattern of drug is analyzed and found to follow Weibull and Higuchi equations. The permeation profiles were obtained for all formulations: NDPSLN A, NDPSLN B, and NDPNLC. Of all the three formulations, NDPNLC provided the greatest enhancement for NDP flux (21.485 ± 2.82 μg/h/cm²), which was fourfold over control (4.881 ± 0.96 μg/h/cm²). The flux obtained with NDPSLN B (16.983 ± 2.91 μg/h/cm²) and NDPNLC (21.485 ± 2.82 μg/h/cm²) meets the required flux (16.85 μg/h/cm²).     

Heat recovery stamp charged coke making: An experience in operational excellence

The coal blend quality and process control of coke making technologies is an important lever to produce quality coke with optimal cost. Apart from impacting cost, this improves the CO₂ footprint. This is facilitated by proper selection of coke making technologies and coal/coal blend. Each technology has its own advantage and limitation based on its design criteria. Recently, Tata Steel introduced Asia largest single location 1.6 mtpa of heat recovery coke plant for the first time. This paper briefly described the operational philosophy evolved in heat recovery coke plant to produce desired quality coke at comparatively lower cost through operational excellence. The reduction of imported prime hard coking coal in coal blend up to 30% without affecting coke quality adversly and understanding the operational processes and finally mastering heat recovery coke making technology was also part of this paper.     

Development of nitrendipine controlled release formulations based on SLN and NLC for topical delivery: in vitro and ex vivo characterization

The aim of the investigation is to develop solid lipid nanoparticles (SLN) and nano-structured lipid carrier (NLC) as carriers for topical delivery of nitrendipine (NDP). NDP-loaded SLN and NLC were prepared by hot homogenization technique followed by sonication, and they were characterized for particle size, zeta potential, entrapment efficiency, stability, and in vitro release profiles. Also the percutaneous permeation of NDPSLN A, NDPSLN B, and NDPNLC were investigated in abdominal rat skin using modified Franz diffusion cells. The steady state flux, permeation coefficient, and lag time of NDP were estimated over 24 h and compared with that of control (NDP solution). The particle size was analyzed by photon correlation spectroscopy (PCS) using Malvern zeta sizer, which shows that the NDPSLN A, NDPSLN B, and NDPNLC were in the range of 124-300 nm during 90 days of storage at room temperature. For all the tested formulations (NDPSLN A, NDPSLN B, and NDPNLC), the entrapment efficiency was higher than 75% after 90 days of storage. The cumulative percentage of drug release at 24 h was found to be 26.21, 30.81, and 37.52 for NDPSLN A, NDPSLN B, and NDPNLC, respectively. The results obtained from in vitro release profiles also indicated the use of these lipid nanoparticles as modified release formulations for lipophilic drug over a period of 24 h. The data obtained from in vitro release from NDPSLN A, NDPSLN B, and NDPNLC were fitted to various kinetic models. High correlation was obtained in Higuchi and Weibull model. The release pattern of drug is analyzed and found to follow Weibull and Higuchi equations. The permeation profiles were obtained for all formulations: NDPSLN A, NDPSLN B, and NDPNLC. Of all the three formulations, NDPNLC provided the greatest enhancement for NDP flux (21.485 +/- 2.82 microg/h/cm(2)), which was fourfold over control (4.881 +/- 0.96 microg/h/cm(2)). The flux obtained with NDPSLN B (16.983 +/- 2.91 microg/h/cm(2)) and NDPNLC (21.485 +/- 2.82 microg/h/cm(2)) meets the required flux (16.85 microg/h/cm(2)).