Effect of surfactants on phenol removal by the method of polymerization and precipitation catalysed by Coprinus cinereus peroxidase

The removal of phenol by peroxidase‐catalysed polymerization was examined using Coprinus cinereus peroxidase in the presence of surfactants. The non‐ionic surfactants with poly(oxyethene) residues, Triton X‐100, Triton X‐405 and Tween 20, enhanced the phenol removal efficiency at a level similar to high relative molecular mass poly(ethylene glycol) (relative molecular mass 3000). Although the improvement in the removal efficiency was less than that of Triton X‐100, Span 20, sodium lauryl sulfate (SDS) and lauryl trimethylammonium bromide (DTAB) also enhanced the removal efficiency. The requirement of the enzyme for almost 100% removal of 100 mg dm^?3 phenol decreased to one‐fourth by the addition of 30 mg dm^?3 Triton X‐100. Triton X‐100, Triton X‐405, Tween 20 and DTAB could reactivate the enzyme precipitated with the phenol polymer, leading to the restarting of the phenol removal reaction. Copyright © 2003 Society of Chemical Industry     

Photothermal self-oscillation and laser cooling of graphene optomechanical systems

By virtue of their low mass and stiffness, atomically thin mechanical resonators are attractive candidates for use in optomechanics. Here, we demonstrate photothermal back-action in a graphene mechanical resonator comprising one end of a Fabry-Perot cavity. As a demonstration of the utility of this effect, we show that a continuous wave laser can be used to cool a graphene vibrational mode or to power a graphene-based tunable frequency oscillator. Owing to graphene's high thermal conductivity and optical absorption, photothermal optomechanics is efficient in graphene and could ultimately enable laser cooling to the quantum ground state or applications such as photonic signal processing.     

Extremely narrow spectral linewidth and low chirping of theMQW-DFB-PPIBH laser diode

The low threshold current of 9 mA, the high side-mode suppression ratio of more than 45 dB, the extremely narrow spectral linewidth of 1.1 MHz, and the low chirping of 2.8 Å at -20 dB at 2 Gb/s nonreturn to zero (NRZ) modulation have been achieved in the multiple quantum well (MQW) distributed feedback (DFB) p-substrate partially inverted buried heterostructure (PPIBH) laser diode. The spectral linewidth of 1.1 MHz is the narrowest value among 300-μm-length solitary laser diodes. These results suggest that the MQW-DFB laser diodes are a promising light source for longer distance and higher bit-rate optical communication systems and coherent optical communication systems     

Reusable Floating Beads with Immobilized Xylose-Fermenting Yeast Cells for Simultaneous Saccharification and Fermentation of Lime-Pretreated Rice Straw

Novel bioreactor beads for simultaneous saccharification and fermentation (SSF) of lime-pretreated rice straw (RS) into ethanol were prepared. Genetically modified Saccharomyces cerevisiae cells expressing genes encoding xylose reductase, xylitol dehydrogenase, and xylulokinase were immobilized in calcium alginate beads containing inorganic lightweight filler particles to reduce specific gravity. For SSF experiments, the beads were floated in slurry composed of lime-pretreated RS and enzymes and incubated under CO₂ atmosphere to reduce the pH for saccharification and fermentation. Following this reaction, beads were readily picked up from the upper part of the slurry and were directly transferred to the next vessel with slurry. After 240 h of incubation, ethanol production by the beads was equivalent to that by free cells, a trend that was repeated in nine additional runs, with slightly improved ethanol yields. Slurry with pre-saccharified lime-pretreated RS was subjected to SSF with floating beads for 168 h. Although higher cell concentrations in beads resulted in more rapid initial ethanol production rates, with negligible diauxic behavior for glucose and xylose utilization, no improvement in the ethanol yield was observed. A fermentor-scale SSF experiment with floating beads was successfully performed twice, with repeated use of the beads, resulting in the production of 40.0 and 39.7 g/L ethanol. There was no decomposition of the beads during agitation at 60 rpm. Thus, this bioreactor enables reuse of yeast cells for efficient ethanol production by SSF of lignocellulosic feedstock, without the need for instruments for centrifugation or filtration of whole slurry.     

Preparation and properties of transparent cellulose hydrogels

Highly transparent cellulose hydrogels with physical crosslinkage were prepared from nonaqueous organic cellulose solutions and viscose by coagulating and regenerating cellulose in an aqueous solution containing a water‐miscible organic solvent. Nonaqueous organic cellulose solutions used were LiCl/dimethylacetamide, paraformaldehyde/dimethyl sulfoxide, and triethylammonium chloride/dimethyl sulfoxide. Preparation conditions and physical properties of the transparent cellulose hydrogels were studied. The transparency of the cellulose hydrogels depended on the composition of the aqueous solution containing the organic solvent. Furthermore, transparent cellulose hydrogels from viscose showed high tensile strength. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 3020–3025, 2003     

Structural stability and mechanochemical activity of titanium nitride prepared by mechanical alloying

Pure titanium nitride (TiN) was synthesized by mechanical alloying (MA). In order to prevent the contamination from the MA vial and atmospheric gas, the MA steel vial was replaced with a titanium vial and atmospheric gas was deoxidized using sponge titanium heated to 623 K. The mechanochemical activity during MA was estimated from the gas purification temperature. The investigation of thermal and pressure stability by thermal treatment and hot isostatic pressing (HIP) revealed that titanium nitride, TiN, was stable on heating to 1173 K under a vacuum, but became unstable under a high pressure, 100 MPa.