Effect of plate-like glass fillers on the mechanical properties of dental nanocomposites

In this study, glass flakes were incorporated into the spherical nanosilica component of the dental composites and its effect on the mechanical properties of these composites was investigated. To achieve a good interfacial adhesion between matrix resin and fillers, the particles were surface treated with a silane coupling agent (γ-MPS). Composites with different plate-like and spherical nanoparticle contents were prepared and their mechanical properties, including flexural strength, flexural modulus and fracture toughness were measured. The morphology of the particles and fracture surface of the composites were studied by SEM. The distribution of the flakes in the composite was also monitored using EDXA. Statistical analysis of the data was performed with ANOVA and the Tukey’s post hoc test was at a significance level of 0.05. The results showed that the flexural modulus and fracture toughness of specimens were improved with increasing the glass flake content up to 15 vol % which then declined upon further increase due to the stacking of the flakes on each other. A good interfacial adhesion was observed between matrix resin and particles in the SEM micrographs. The results of this study suggest that incorporation of glass flakes into the dental composites containing spherical nanosilica particles may enhance their mechanical properties.     

On estimating the interface normal and curvature in piecewise linear interface calculation-volume of fluid approach for three-dimensional arbitrary meshes

Volume of fluid (VOF) method with its Piecewise Linear Interface Calculation (PLIC) reconstruction algorithm is one of the most popular approaches in numerical simulation of interfacial flows with a wide range of applications in different areas. In an effort to evaluate the similarity of the PLIC-generated planes in comparison with the exact interface, a point-cloud, based on the polygon centers of PLIC planes is extracted, which later is used to form a triangular grid that represents the estimated interface. The main objective of this article is to evaluate the interface geometrical properties based on the extracted triangular grid of the interface. The methods presented in this article, characterized by a higher spatially convergence ratio, are compared with the commonly used methods. The proposed methods are tested for two 3-dimensional general test cases, where an evident improvement is seen in calculation accuracy and spatial convergence of the errors of interface normal vector and curvature.     

Nutrition education alone improves dietary practices but not hematologic indices of adolescent girls in Iran

BACKGROUND: Iron-deficiency anemia is the most prevalent nutritional deficiency worldwide. Iron-deficiency anemia has particular negative consequences on women in their childbearing years, and its prevention is a high priority in most health systems. OBJECTIVE: This interventional study assessed the effect of nutrition education on hematologic indices, iron status, nutritional knowledge, and nutritional practices of high-school girls in Iran. METHODS: Sixty healthy 16- to 18-year-old girls were randomly selected from two high schools in the city of Ahvaz and divided into two equally matched groups, one that received nutrition education, and one that did not. The education group received instruction in face-to-face sessions, group discussions, and pamphlets for 2 months. The control group did not receive any information during the study. Hematologic tests, corpuscular indices, and serum ferritin levels were measured at baseline and after 2 months. Food-frequency questionnaires were administered and histories taken, clinical signs of nutritional deficiencies observed, anthropometric measurements taken, nutritional knowledge tested, practices determined, and lifestyle questionnaires administered to all subjects. RESULTS: There were no statistically significant differences in any baseline characteristics between the two groups. Scores for nutritional knowledge and practices of the education group were significantly higher after two months compared with the baseline (31.4 +/- 6 vs. 24.3 +/- 5.9 points, p < .001, and 31.2 +/- 5 vs. 28.4 +/- 5.7 points, p < .05, respectively). The scores in the control group showed no significant changes from baseline to 2 months. Mean corpuscular volume values were elevated in the education group (p < .001) but not in the control group. However, in the control group, serum ferritin concentrations showed about a 17% drop at the end of the study (p < .004). There were no changes in other hematologic, lifestyle, clinical, or anthropometric data compared with baseline after completion of the study in both groups. CONCLUSION: These findings indicate that nutritional education can improve knowledge of healthy nutrition and lifestyle choices. Focused nutritional education using available resources and correcting current dietary habits in a vulnerable group of young women may result in dietary changes that can ultimately improve iron intake.     

Investigation of hydrodynamic and mass transfer of mercaptan extraction in pulsed and non-pulsed packed columns

We investigated the hydrodynamic behavior and mass transfer characteristics of a pilot-scale conventional packed bed extraction column of mercaptan removal from liquid propane. The extraction column was filled with pall rings structured packing where mercaptan was extracted from the continuous phase to the dispersed phase, accompanied by a chemical reaction in propane-mercaptan-caustic system. The pulsing was introduced into the column to enhance the mass transfer rate. Hydrodynamic parameters such as hold up, flooding velocity and mean drop size were studied together with the effect of chemical reaction on increasing mass transfer performance. Finally, the mass transfer and axial mixing coefficients were obtained from the optimization of data by ADM. It was found that at the pulsation intensity from 0.003 to 0.007 m/s, the maximum mass transfer and minimum axial mixing occurred and it can be concluded that pulsation improves the efficiency of mass transfer just at low intensities.     

Well-defined core-shell nanoparticles containing cyclodextrin in the shell: A comprehensive study

The purpose of this study was to conceive novel nanoparticles (NPs) designed for drug delivery applications. The NPs were based on a hydrophobic poly (lactic acid) (PLA) core and a hydrophilic β-cyclodextrin polymer (Poly-β-CD) shell. The PLA NPs were prepared by the nanoprecipitation method. The Poly-β-CD shell was obtained by adsorption from Poly-β-CD solution. Different complementary techniques have been used to fully characterize the system including dynamic light scattering, Zeta potential measurements, solution proton nuclear magnetic resonance spectroscopy, transmission electron microscopy, and small angle neutron scattering. They provide good evidence of a core-shell structure. The NPs parameters are dependent on the elaboration process, Poly-β-CD characteristics and adsorption conditions. In the conditions of adsorption’ saturation, the shells were constituted of Poly-β-CD monolayers covering the PLA surfaces with adsorption amounts from 2 to 4 mg/m², allowing reaching Poly-β-CD weight fractions of 10-20% in the NPs.     

Measurement of Consumed Energy Due to the Two-Phase Pressure Drop in a Pulsed Semi-Industrial Column: Effect of Geometry

This article deals with the evaluation of pressure drop and consumption of energy for a steady-state solvent extraction in a horizontal pulsed sieve-plate column, which are important for the design and optimization of the periodic-flow processes for industrial applications. In this study, the pressure drop and the position of loading points are investigated. Moreover, a mathematical evaluation on the energy consumption in the case of a pulsed flow is conducted, and besides the influence of pulsation intensity, the effect of geometrical parameters including the plate spacing and plate-free area is investigated as well. The results of this study are helpful for optimization of column geometry targeted to higher performance and lower energy consumption.     

Proton conductivity and morphology of new composite membranes based on zirconium phosphates,phosphotungstic acid,and silicic acid for direct hydrocarbon fuel cells applications

The effect of Phosphotungstic acid (PWA) on the proton conductivity and morphology of zirconium phosphate (ZrP), porous polytetrafluoethylene (PTFE), glycerol (GLY) composite membrane was investigated in this work. The composite membranes were synthesized using two approaches: (1) Phosphotungstic acid (PWA) added to phosphoric acid and, (2) PWA + silicic acid were added to phosphoric acid. ZrP was formed inside the pores of PTFE via the in situ precipitation. The membranes were evaluated for their morphology and proton conductivity. The proton conductivity of PWA–ZrP/PTFE/GLY membrane was 0.003 S cm^?1. When PWA was combined with silicic acid, the proton conductivity increased from 0.003 to 0.059 S cm^?1 (became about 60% of Nafion’s). This conductivity is higher than the proton conductivity of Nafion–silica–PWA membranes reported in the literature. The SEM results showed a porous structure for the modified membranes. The porous structure combined with this reasonable proton conductivity would make these membranes suitable as the electrolyte component in the catalyst layer for direct hydrocarbon fuel cell applications.     

Microstructure, property and processing relation in gradient porous cathode of solid oxide fuel cells using statistical continuum mechanics

This paper investigates the relation between microstructure, macroscopic transport properties, and fabrication processing for a gradient porous cathode of solid oxide fuel cells (SOFCs). Functionally graded porous cathode with smooth variations in pore size is composed of lanthanum strontium manganite (LSM) fabricated on yttria stabilized zirconia (YSZ) electrolyte substrate using a multi-step spray pyrolysis (SP) technique at various deposition conditions. Two-dimensional (2D) serial-sections of the gradient porous microstructure obtained by FIB-SEM are fully characterized using statistical correlation functions. Results of statistical analysis of the microstructures revealed that the SP processing technique is capable of generating statistically identical and homogeneous microstructures with smooth gradient in pore size resulting from changing the processing parameters. Strong contrast statistical approach is also used to predict the in-plane temperature dependent effective electrical conductivity of the gradient porous cathode and the results are compared to the experimental data.     

Object-based hyperspectral image classification using a new latent block model based on hidden Markov random fields

Pattern Analysis and Applications - Efficient high-dimensional analyses of hyperspectral datasets and their utilization within classification algorithms is a popular topic in the field of data...     

Novel composite membrane based on zirconium phosphate-ionic liquids for high temperature PEM fuel cells

Composite membranes composed of zirconium phosphate (ZrP) and imidazolium-based ionic liquids (IL), supported on polytetrafluoroethylene (PTFE) were prepared and evaluated for their application in proton exchange membrane fuel cells (PEM) operating at 200 °C. The experimental results reported here demonstrate that the synthesized membrane has a high proton conductivity of 0.07 S cm^?1, i.e, 70% of that reported for Nafion. Furthermore, the composite membranes possess a very high proton conductivity of 0.06 S cm^?1 when processed at 200 °C under completely anhydrous conditions. Scanning electron microscopy (SEM) images indicate the formation of very small particles, with diameters in the range of 100–300 nm, within the confined pores of PTFE. Thermogravimetric analysis (TGA) reveals a maximum of 20% weight loss up to 500 °C for the synthesized membrane. The increase in proton conductivity is attributed to the creation of multiple proton conducting paths within the membrane matrix. The IL component is acting as a proton bridge. Therefore, these membranes have potential for use in PEM fuel cells operating at temperatures around 200 °C.