Establishment time of liquid flow in a bath agitated by bottom gas injection

The establishment time of gas-liquid two-phase flows in a cylindrical bath agitated by bottom gas injection through a central single-hole bottom nozzle was investigated. Because the turbulence intensity in the bath was comparable to or larger than the unity, the conventional definition of the flow establishment time based on the history of mean velocity was not suitable for the present case. In fact, it was difficult to determine the flow establishment time based on the well-known 90 or 99 pct criterion for the mean velocity. Accordingly, two methods of determining the flow establishment time by focusing on the turbulence components instead of the mean velocity components were proposed. Velocity measurements were made with a two-channel laser Doppler velocimeter. The flow establishment time was correlated as a function of gas flow rate. Close agreement was obtained by the two methods.     

Changes in Aging Behavior and Defect Structure of Yttria-Fully-Stabilized ZrO2 with Sc2O3 Doping

Methods of suppressing decreased conductivity in 8 mol% Y₂O₃-stabilized–92 mol% ZrO₂ (8YSZ) with aging were investigated. Different amounts of Sc₂O₃ were doped into 8YSZ. The electrochemical properties of Sc₂O₃-doped 8YSZ were measured, and the microstructural and local structural changes were characterized. The present results indicate that an appropriate amount of Sc₂O₃ doping, 3 or 4 mol%, effectively suppresses decreased conductivity with aging in 8YSZ.     

Triglyceride analysis by combined argentation/nonaqueous reversed phase high performance liquid chromatography

Full analysis of triglycerides of natural fats and oils has been investigated by the combination of argentation high performance liquid chromatography (HPLC) with nonaqueous reversed phase (NARP) HPLC. An infrared detector was used in argentation HPLC, because it indicated molar responsibility to all triglycerides. After peak trapping with argentation HPLC, each triglyceride fraction was analyzed with NARP chromatography using the glyceride-selective post-column reactor detector. The results of the analyses of triglycerides of palm oil and cocoa butter by the proposed method agreed well with those reported earlier.     

Microstructure and mechanical properties of hot extruded Mg–Al–Mn–Ca alloy produced by rapid solidification powder metallurgy

The microstructure and mechanical properties of hot extruded Mg–Al–Mn–Ca alloy was investigated. Both rapid solidified powders and cast billets were extruded at 573, 623 and 673 K to optimize the processing conditions for obtaining better mechanical response. Powder was consolidated to prepare the extrusion billets using both cold compaction and Spark Plasma Sintering at 473 K. The tensile properties of the extruded alloy were then evaluated and correlated to the observed microstructure. The results show that the use of rapid solidified powder could lead to effective grain refinement, which in turn resulted in the improved mechanical response, especially compared to the extruded conventional cast material.     

Effect of CNTs on Activation Volume and Mobile Dislocation Exhaustion Rate of CNTs/Al under Compression Loading

In this study, stress relaxation compression tests were performed to investigate the strain rate sensitivity, activation volume and mobile dislocations in carbon nanotubes/aluminum (CNTs/Al) composites. The results reveal that, with the addition of CNTs, the strain rate sensitivity of CNTs/Al increased. Meanwhile, a smaller V^* of CNTs/Al compared with pure Al was attributed mainly to the CNT-Al interfaces and partly to the increased forest dislocations cutting activities in grain interior, which was related to the tendency of short ranges order formation during plastic deformation. The incorporation of CNTs also improved the dislocation storage capability and reduced the dislocation velocity, leading to a lower mobile dislocation exhaustion rate.     

Proposal of cause–effect pattern library for realizing sustainable businesses

Sustainable business design has gained growing interest in recent years. However, it is often difficult to clarify which business activities actually contribute to (or violate) the sustainability of the earth due to high complexity of environmental and economical system of our society. In order to help a business to generate sustainable business ideas handling this complexity in a systematic and comprehensive manner, this paper proposes a method to formulate a wide variety of causalities in our society into a cause–effect pattern library and illustrates how to use it for design and planning of sustainable businesses.     

Quantification of wear,strain and heat energy consumption rates for sliding steel ball against diamond-like carbon coatings

Abstract

In this work, we evaluated the different energy consumption rates associated with the total frictional energy for a ball sliding on a flat surface. The energy generated by the sliding two bodies in contact is dissipated into the materials in various forms. The wear consumption energy for a steel ball against a diamond-like carbon surface was evaluated by the wear coefficient of the wear volume–energy input equation. The strain energy generated in the steel ball as a result of being made to slide under a certain load was calculated using the Hertzian theory. The chemical reaction energy was estimated based on iron oxidation. Finally, the frictional energy dissipated as heat was obtained by subtracting the wear and the strain energies from the total frictional energy.     

High-reliability, high-performance RF micromachined switch using liquid metal

Existing mechanical relays have reliability-related issues including unstable contact resistance and limited cycle life. These problems are caused by mechanical fatigue and wearing of the contact surfaces. In the liquid metal micro switch (LiMMS), we employ a liquid-liquid contact to address these issues. The switching operation is achieved by forming a gap in the liquid metal using gas expansion. Our prototype has a microchannel on a glass substrate to hold a tiny amount of mercury, 0.15 mm in width and 0.1 mm in height, and TaN thin-film heaters on a ceramic substrate to expand the operating gas by heating. The substrates are bonded together and the total size of the device is 5/spl times/5/spl times/1.4 mm. We successfully demonstrated 70-m/spl Omega/ on-resistance, 1 ms-switching speed, the ability to handle up to 1 A of dc current and over 1/spl times/10/sup 8/ cycle operation. LiMMS also has good RF performance, better than 1 dB insertion loss, and better than 20 dB isolation up to 18 GHz.     

Evaluation of MRCP compared to ERCP in the diagnosis of biliary and pancreatic duct

Recently, Magnetic Resonance Cholangiopancreatography (MRCP) is developed as a noninvasive diagnostic modality in the diagnosis of biliary and pancreatic tract. Using Endoscopic Retrograde Cholangiopancreatography (ERCP) as the gold standard, we evaluated the diagnostic quality of MRCP and direct cholangiography. Fifty-six patients (9 cases of cholangiocarcinoma, 5 of gallbladder carcinoma, 1 of gallbladder carcinoma and anomalous arrangement of pancreaticobiliary ductal system, 4 of cholecystlithiasis, 3 of papillary carcinoma, 1 of adenomyomatosis of the gallbladder, 1 of primary sclerosing cholangitis, 1 of hepatolithiasis and postoperative bile duct stricture, 4 of mucin producing pancreatic tumor, 13 of pancreatic carcinoma, 1 of chronic pancreatitis and pancreas divisum, 9 of chronic pancreatitis, and 1 of chronic pancreatitis and biliary stricture) are studied prospectively with MRCP and direct cholangiography (included ERCP and percutaneous transhepatic cholangiography). The image of MRCP accorded with direct cholangiography in twenty-two of 27 patients with biliary tract disease, and in sixteen of 29 patients with pancreatic disease. The different diagnosis is observed in ten of 56 patients. In cases of not visualized gallbladder, pancreatic cyst without communicated to the pancreatic duct, and pre-stenotic dilatation of biliary and pancreatic duct, the image of MRCP was better than that of ERCP. However, the image of MRCP for the diagnosis of either benign or malignant strictures, mucin producing pancreatic tumor, and a branch of pancreatic duct in patients with pancreatic carcinoma were not suitable for evaluation than that of ERCP. In our study, ERCP is superior to MRCP due to the important information for diagnosis such as mentioned above. Therefore we advocate using ERCP as the first diagnostic tool in the diagnosis of biliary and pancreatic duct.     

Fabrication of nanoscale tungsten tip arrays for scanning probemicroscopy-based devices

A new fabrication process for nanoscale tungsten tip arrays was developed for scanning probe microscopy-based devices. It is suitable to make a huge array on a device chip and is potentially compatible with CMOS technology. In this study, tungsten was selected as a tip material because of its hardness and conductivity. The newly developed fabrication process mainly consists of several important techniques: a combination of optical lithography and electron beam (EB) lithography to reduce the total exposure time with high resolution and chromium/tungsten/chromium (Cr/W/Cr) sandwich deposition and etching in which the first chromium layer is used as a mask and a second one is used as an etch stop. A periodic array of dots in an EB resist with a spot diameter of less than 50 nm was obtained by a combination of optical lithography and EB lithography with a positive resist (polymethylmethacrylate) in which all processing conditions were optimized carefully. A thin and uniform chromium film, deposited by ion-beam sputtering, allowed the use of thin polymethylmethacrylate (PMMA) film which led to the high resolution. The conditions of dc magnetron sputtering were also optimized in order to deposit a densely packed and low-resistivity film. The resulting tungsten tip arrays had a cylindrical shape with diameters of less than 60 nm and heights of 300 nm