A probabilistic model for cleavage fracture with a length scale--parameter estimation and predictions of stationary crack experiments

This study presents a large experimental investigation in the transition temperature region on a modified A508 steel. Tests were carried out on single-edge-notch-bend specimens with three different crack depth over specimen width ratios to capture the strong constraint effect on fracture toughness. Three test temperatures were considered, covering a range of 85 °C. All specimens failed by cleavage fracture prior to ductile tearing. A recently proposed probabilistic model for the cumulative failure by cleavage was applied to the comprehensive sets of experimental data. This modified weakest link model incorporates a length scale, which together with a threshold stress reduce the scatter in predicted toughness distributions as well as introduces a fracture toughness threshold value. Model parameters were estimated by a robust procedure, which is crucial in applications of probabilistic models to real structures. The conformity between predicted and experimental toughness distributions, respectively, were notable at all the test temperatures.     

The Gas-to-Particle Heat Transfer and Hydrodynamics in Spouted Bed Drying of Sawdust

This article presents experimental results for spouted bed drying of sawdust, carried out in a full-scale as well as in a laboratory-scale dryer using air as well as steam as drying media. The aim is to present design parameters for a spouted-bed sawdust dryer that can be used by the industry in designing full-scale dryers. A hydrodynamically stable spouted jet spouted bed was obtained. The heat transfer characteristics of the bed were represented in terms of a volumetric heat transfer coefficient (VHC). When sawdust is dried in a spouted bed, the mean VHC is increasing up to fiber saturation level (20-25% wb) from 40 to 110 W/m³ K. The VHC decreases with the residence time and with an increased static bed height. Gas temperature profiles are also presented for the bottom part of the drying chamber.     

Manufacturing method for monolithic dye-sensitised solar cells permitting long-term stable low-power modules

A manufacturing technique for monolithic dye-sensitised solar cells is presented. Encapsulated modules designed for indoor low-power applications have been prepared using industrial methods and equipment. Under certain conditions (light intensity <5000 lx, temperature between –10°C and 50°C, and relative humidity of appr. 50%), the modules have performed well and shown excellent long-term stability. Moreover, modules withstand illumination in combination with storage at 100% relative humidity. However, a certain degradation of the module performance takes place at illuminations exceeding 5000 lx and temperatures exceeding 50°C.     

D-lactic acidosis: a treatable encephalopathy in pediatric patients

Isolation of Salmonella from the feces of impounded dogs was carried out to make clear the recent microbiological condition of dogs introduced into our facilities. Salmonella was isolated from 10 out of 283 samples (3.5%). Inparticular, during the first week after introduction, Salmonella was isolated from nine out of 74 dogs (12.2%). The isolation rate during the first week after introduction was significantly higher than that for dogs introduced later. No isolates were detected from dogs reared for more than 3 weeks after introduction. This study indicates that impounded dogs had the highest risk of infecting a person with Salmonella during the first week after introduction into our laboratory animal facilities, and that we need to pay attention to this fact when handling them.     

Lack of de-epoxidation of type B trichothecenes in incubates with human faeces

The ability of human gastrointestinal organisms to transform the trichothecenes 3-acetyldeoxynivalenol and nivalenol was investigated. Samples of human faeces were incubated under anaerobic conditions for 48 h with the toxins. They were then extracted and analysed for trichothecenes and metabolites. 3-Acetyldeoxynivalenol was metabolized to deoxynivalenol during the incubation period. In contrast to what has been reported for other species such as rats, mice and pigs, no de-epoxidated metabolites were detected in the faecal incubates. The toxicological significance of the difference in the intestinal ability to transform trichothecenes between species is unknown.     

Influence of strain rate on interpass softening

Most laboratory simulations of hot rolling involve a scaling down of the strain rate from the much higher industrial levels. This leads to slower softening between each rolling pass, for which corrections must be made. In the present work, torsion testing simulations of “warm” rod rolling were conducted on a Ti-Nb interstitial-free (IF) steel at 840 °C and 770 °C(i.e., in the ferrite range). For this purpose, “strain rate corrected” interpass times were used, in addition to the more familiar corrections for the stress. The results are compared with those obtained from simulations using uncorrected industrial interpass times. At 840 °C, simulations using corrected interpass times led to high levels of softening between the stages of rolling, thus triggering the reinitiation of cycles of dynamic recrystallization. The initially high stress level at the start of these cycles was responsible for the large differences in the pass-to-pass mean flow stress behavior, compared with that observed when using uncorrected industrial interpass times, or continuous deformations. The differences were much less pronounced at 770 °C, where the rate of softening is much slower than at 840 °C. Predictions for softening based on the Avrami equation underestimated the softening observed using the continuous and uncorrected industrial interpass time schedules and overestimated it for the corrected ones. The former is due to the occurrence of recovery, which is not addressed by the Avrami relation, while the latter is due to the precipitation that takes place during the corrected (longer) interpass times. It was also found that simulations using continuous deformations are applicable only if the interpass softening that would be expected using the corrected interpass times does not exceed about 20 pct.     

Probabilistic cell modelling of cleavage fracture

Various aspects on probabilistic modelling of cleavage fracture are discussed. The investigation involves consideration of a unit cell with an explicitly modelled void. The results from this model are compared with results for the case when the void content is accounted for in the sense of a Gurson-Tvergaard law. It is found that explicit modelling of the void can give substantially different results for the fracture probability. The effect depends on the exponent in the assumed Weibull distribution, the threshold stress, the constraint conditions and the hardening of the material. This revised version was published online in August 2006 with corrections to the Cover Date.     

Nonlinear black-box modeling in system identification: a unified overview

A nonlinear black-box structure for a dynamical system is a model structure that is prepared to describe virtually any nonlinear dynamics. There has been considerable recent interest in this area, with structures based on neural networks, radial basis networks, wavelet networks and hinging hyperplanes, as well as wavelet-transform-based methods and models based on fuzzy sets and fuzzy rules. This paper describes all these approaches in a common framework, from a user's perspective. It focuses on what are the common features in the different approaches, the choices that have to be made and what considerations are relevant for a successful system-identification application of these techniques. It is pointed out that the nonlinear structures can be seen as a concatenation of a mapping form observed data to a regression vector and a nonlinear mapping from the regressor space to the output space. These mappings are discussed separately. The latter mapping is usually formed as a basis function expansion. The basis functions are typically formed from one simple scalar function, which is modified in terms of scale and location. The expansion from the scalar argument to the regressor space is achieved by a radial- or a ridge-type approach. Basic techniques for estimating the parameters in the structures are criterion minimization, as well as two-step procedures, where first the relevant basis functions are determined, using data, and then a linear least-squares step to determine the coordinates of the function approximation. A particular problem is to deal with the large number of potentially necessary parameters. This is handled by making the number of ‘used’ parameters considerably less than the number of ‘offered’ parameters, by regularization, shrinking, pruning or regressor selection.