Identification of the adverse effect of nitrate on the phosphate release rate and improvement of EBPR process models.

The adverse effect of nitrate on the phosphate release rate in the anaerobic phase was observed and was hardly explainable with conventional EBPR process models. Four possible mechanisms were proposed including substrate competition, reduced fermentation, parallel reaction and sequential reaction. Batch experiments were designed and conducted to identify the dominant mechanism. Results showed that the sequential reaction was the only possible mechanism where only denitrification occurred if any nitrate existed in the anaerobic phase. Then the phosphate release following after the nitrate was completely removed. Nitrate inhibition effect was added into the PHA storage rate to incorporate the sequential reaction in the conventional ASM3 plus EAWAG bio-P module (ASM3 + P). Nitrate inhibition coefficient, K(I,NO,PAO) was found to be as low as 0.05 mg/L. This correlated well with experimental observation where no also meant that the anaerobic compartment of a continuous flow reactor could be seriously affected by the residual nitrate contained in the sludge recycle flow. This phenomenon caused overestimation of the phosphate uptake rate and consequently underestimation of PO4(3-) -P concentration. This problem was resolved by incorporation of a nitrate inhibition term in the ASM3 + P for more accurate simulation of the EBPR process.     

A power-driven multiplication instruction-set design method for ASIPs

This paper presents a novel power-driven multiplication instruction-set design method for application-specific instruction-set processors (ASIPs). Based on a dual-and-configurable-multiplier structure, our proposed method devises a multiplication instruction set for low-power ASIPs. Our method exploits the execution sequences of multiplication instructions and effective bit widths of variables to reduce power consumed by redundant multiplication bits while minimizing the multiplication execution time. Experimental results on a set of DSP programs demonstrate that our proposed method achieves significant power reduction (up to 18.53%) and execution time improvement (up to 10.43%) with 18% area overhead.     

Microstrip stepped impedance resonator bandpass filter with an extended optimal rejection bandwidth

Bandpass filters with an optimal rejection bandwidth are designed using parallel-coupled stepped impedance resonators (SIRs). The fundamental (f/sub o/) and higher order resonant harmonics of an SIR are analyzed against the length ratio of the high-Z and low-Z segments. It is found that an optimal length ratio can be obtained for each high-Z to low-Z impedance ratio to maximize the upper rejection bandwidth. A tapped-line input/output structure is exploited to create two extra transmission zeros in the stopband. The singly loaded Q(Q/sub si/) of a tapped SIR is derived. With the aid of Q/sub si/, the two zeros can be independently tuned over a wide frequency range. When the positions of the two zeros are purposely located at the two leading higher order harmonics, the upper rejection band can be greatly extended. Chebyshev bandpass filters with spurious resonances up to 4.4f/sub o/, 6.5f/sub o/, and 8.2f/sub o/ are fabricated and measured to demonstrate the idea.     

Reducing cycle times in manufacturing and supply chains by input and service rate smoothing

A key performance parameter of a manufacturing network or supply chain is its cycle time; the time that a typical item spends in the network. A previous simulation study on a semiconductor assembly and test facility showed that cycle times could be reduced by having smooth input and service rates. This suggested that there is a “cycle time principle” that, for a system with a specified throughput or input rate, the shortest cycle times are obtained when the input and service rates do not vary over time. We prove that this principle is true for the M/G/1 and M/M/s queueing systems and Jackson networks. The analysis involves establishing several results on the concavity of waiting time probabilities and the convexity of expected waiting times and queue lengths, as functions of input and service rates. These results also have natural uses in other optimization problems.     

A robust classification procedure based on mixture classifiers and nonparametric weighted feature extraction

There are many factors to consider in carrying out a hyperspectral data classification. Perhaps chief among them are class training sample size, dimensionality, and distribution separability. The intent of this study is to design a classification procedure that is robust and maximally effective, but which provides the analyst with significant assists, thus simplifying the analyst's task. The result is a quadratic mixture classifier based on Mixed-LOOC2 regularized discriminant analysis and nonparametric weighted feature extraction. This procedure has the advantage of providing improved classification accuracy compared to typical previous methods but requires minimal need to consider the factors mentioned above. Experimental results demonstrating these properties are presented.     

High-resolution electron microscopy of the twinning and intergrowth in Ca4Al6SO16 and Ca3SrAl6SO16

The microstructures of unhydrated calcium aluminosulphate Ca₄Al₆SO₁₆ and Ca₃SrAl₆SO₁₆ have been studied by high-resolution electron microscopy (HREM). The results showed that twinning and twinned slabs could be introduced taking the [1 1 2] direction as the twin axis so that it seems to be coincident with the law of twinning formed in body-centred cubic structures. A previously reported superlattice with a repeat period twice that of the fundamental structure along the 〈1 1 0〉 direction has also been found in both matrix and twin variants. The close intergrowth of Ca₃SrAl₆SO₁₆ and another phase, possibly Sr₃Al₂O₆ existing as an inclusion between these two twin variants, was determined and clearly revealed by electron diffraction and HREM images. The coherent interphase boundaries and orientation relationship between them can also be deduced.     

Distributed self-stabilizing placement of replicated resources in emerging networks

Emerging large scale distributed networking systems, such as P2P file sharing systems, sensor networks, and ad hoc wireless networks, require replication of content, functionality, or configuration to enact or optimize communication tasks. The placement of these replicated resources can significantly impact performance. We present a novel self-stabilizing, fully distributed, asynchronous, scalable protocol that can be used to place replicated resources such that each node is "close" to some copy of any object. We describe our protocol in the context of a graph with colored nodes, where a node's color indicates the replica/task that it is assigned. Our combination of theoretical results and simulation prove stabilization of the protocol, and evaluate its performance in the context of convergence time, message transmissions, and color distance. Our results show that the protocol generates colorings that are close to the optimal under a set of metrics, making such a protocol ideal for emerging networking systems.     

Using classification techniques for informal requirements in the requirements analysis-supporting system

In order to efficiently develop large-scale and complicated software, it is important for system engineers to correctly understand users’ requirements. Most requirements in large-scale projects are collected from various stakeholders located in various regions, and they are generally written in natural language. Therefore, the initial collected requirements must be classified into various topics prior to analysis phases in order to be usable as input in several requirements analysis methods. If this classification process is manually done by analysts, it becomes a time-consuming task. To solve this problem, we propose a new bootstrapping method which can automatically classify requirements sentences into each topic category using only topic words as the representative of the analysts’ views. The proposed method is verified through experiments using two requirements data sets: one written in English and the other in Korean. The significant performances were achieved in the experiments: the 84.28 and 87.91 F1 scores for the English and Korean data sets, respectively. As a result, the proposed method can provide an effective function for an Internet-based requirements analysis-supporting system so as to efficiently gather and analyze requirements from various and distributed stakeholders by using the Internet.