Performance of the decorrelator receiver for DS-CDMA mobile radio system employing RAKE and diversity through Nakagami fading channel

Multiple-access interference (MAI) and multipath fading are two of the most significant factors limiting the capacity and performance of direct-sequence code-division multiple-access (DS-CDMA) systems. In this paper, synchronous multiuser receivers that combine antenna diversity, RAKE reception, and a multipath decorrelator for MAI cancellation are analyzed in a Nakagami faded environment using a maximal ratio combiner or a selection combiner. A coherent binary phase-shift keying employing DS-CDMA is considered. Arbitrary branch correlation is also considered for any diversity order in the case of identical severity fading on the branches.     

Study of the solid-liquid equilibria in the LiPO3-Y(PO3)3 binary system

The LiPO₃-Y(PO₃)₃ system has been studied for the first time. Microdifferential thermal analysis (μ-DTA), infrared spectroscopy (IR) and X-ray diffraction were used to investigate the liquidus and solidus relations. The only new compound observed within this system is LiY(PO₃)₄, melting incongruently at 1104 K. An eutectic appears at 4±1 mol% Y(PO₃)₃ at 933 K. LiY(PO₃)₄ crystallizes in the monoclinic system C_2/c with a unit cell: a=16.201(4) Å, b=7.013(2) Å, c=9.573(2) Å, β=125.589(9)°, Z=4 and V=884.5 Å³, which is isostructural to LiNd(PO₃)₄. The infrared absorption spectrum indicates that this salt is a chain polyphosphate.     

Effect of functional group of ferrocene redox substance on the transport properties of newly designed ion exchange membrane prepared from polymer gel

A different newly designed cationic exchange polymer membrane and anionic exchange polymer membrane were introduced, and also the transport properties of these polymeric membranes were investigated in this study. The transport properties of these polymer membranes in contact with ferrocene redox derivatives were estimated by using electrochemical techniques such as cyclicvoltammetry, chronopotentiometry, and chronoamperometry techniques, respectively. The used ferrocene redox substances, which have different functional groups, were (Ferrocenylmethyl) trimethylamonium iodide, FcMA, Ferrocenedimethanol, FcDM, and Ferrocene carboxylic acid, FcCA. It indicated that the performance of a membrane depended on the content of polymer gel, anionic exchange polymer site (20 wt % and 50 wt %) or cationic polymer exchange site (20 wt % and 50 wt %), and the efficiency of the functional groups of cationic and anionic exchange polymer site as well. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Water and salt permeability of reinforcement polymer‐gel composite membrane

The charged mosaic polymer membrane (CMM) without reinforcement and the composite charged mosaic polymer membrane (CCMM) with reinforcement were investigated in terms of salt and water transport (permeability). The composite charged mosaic polymer membrane (CCMM) with reinforcement showed a unique transport behavior such as preferential material transport L_p and ω. Water permeability coefficient, L_p and salt permeability coefficient, ω were estimated by taking account of active layer thickness of composite polymer gel. The L_p and ω values of CCMM with reinforcement were larger than those of CMM without reinforcement. On the other hand, the reflection coefficient of CCMM, σ, showed negative value, which suggested preferential material transport to solvent transport. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Radiation polymerization of acrylonitrile in a viscous system with styrene

Radiation polymerization of acrylonitrile in a viscous system with styrene was performed at ambient temperature by using γ‐rays. It is found that the overall rate of polymerization was accelerated after critical conversion due to the gel effect. As the molar fraction of styrene in monomer feed (f_St) is increased, both the total polymer conversion and molar fraction of acrylonitrile in the copolymer feed (F_AN) were decreased. The monomer reactivity ratios for acrylonitrile and styerne were determined to be r₁ (AN) = 0.25 and r₂ (St) = 2.0, respectively. The copolymers obtained were characterized by Fourier transformed infrared spectra (FTIR), X‐ray diffraction (XRD), scanning electron microscopy (SEM), ¹H‐NMR, and pyrolysis mass spectrometry (PMS). It was found that the slight addition of styrene to acrylonitrile strongly changes crystallinity, morphology, and thermal decomposition of the resulting polymer. ¹H‐NMR measurment of AN/St copolymer showed the appearance of aromatic proton signals and shifted the resonance of the methylene proton to lower chemical shifts. The mass spectra of AN/St copolymers showed fragments of pyrolysates corresponding to oligonitriles with styrene end groups. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 84: 268–275, 2002; DOI 10.1002/app.10324     

The Impact of Metastable Intermolrecular Nanocomposite Particles on Kinetic Decomposition of Heterocyclic Nitramines Using Advanced Solid‐Phase Decomposition Models

Journal of Inorganic and Organometallic Polymers and Materials - Surface oxygen of oxide catalyst has low coordination number; they are negatively charged. Surface oxygen can act active site for...     

Modification of leather properties by grafting. I. Effect of monomer chain on the physico‐mechanical properties of grafted leather

Although leather has a number of desirable properties such as thermal stability and fire retardancey, in addition to high toughness, it has a few drawbacks such as weight, high water absorption, poor soil and rot resistance, and nonuniformity. If these defects are overcome, leather's usefulness would be further enhanced and its competitive position with respect to synthetics would increase. This study reports the physical and mechanical properties of buffalo leather after chemical graft copolymerization with ethyl acrylate, butyl acrylate, and 2‐ethyl hexyl acrylate using benzoyl peroxide as an initiator. The optimum conditions for grafting (e.g., monomer and initiator concentrations, temperature and time of grafting, and solvent leather ratio) were extensively investigated. The study achieved outstanding properties for buffalo leather in reduction of water uptake after grafting, especially on using 2‐ethyl hexyl acrylate and butyl acrylate monomers. FT‐IR and solid ¹³C‐NMR for leather before and after grafting confirmed the grafting process.© 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 1478–1483, 2003     

Investigation of Creep Feed Grinding Parameters and Heat treatment Effects on the Nickel-base Superalloys

The Nickel base Superalloys are the most famous complicated and useable of Superalloys to make hot zone components of the gas turbines. The complicated dimensional tolerances, specially at the root of the blade show importance of grinding processes at the production of blades root. The prediction of the effect of machining parameters on the soundness of component surface strengthening for reaching to a suitable surface finishing and avoiding from crack formation at the work part during machining operation often is not easy and feasible so needs to more industrial investigation.This research is about frame 5 blade designed by GE and made from Superalloy IN738LC has been investigated. The formation of a plastically deformed and heat affected zone during grinding of Superalloy IN738LC with a high depth of cut but slow work speed (creep feed grinding) was investigated. Parameters such as work speed, depth of cut and radial dressing speed have been considered as variables and their effects have been studied. During experimental performed, the voltage and current of motor measured and power and special energy calculated.Some samples heat-treated (of the 1176℃ for 1 hr under neutral argon gas and cooling rate of 15℃/min up to 537℃ and then air cooling) to study grains recrystallization. Other samples have been created from the roots of blades and then coated by Nickel to measure boundary layer micro-hardness. The results show that increasing work speed leads to increasing the use power. Increasing the depth of cut, by increasing material removal rate, and the radial dressing speed, by decreasing power, lead to decreasing special energy. The temperature created by grinding lead to decreasing plastic deformation and boundary layer formation. When the radial dressing speed changes from 1 to 0.6μm/rev and other parameters are kept unchanged the roughness of surface increases and the special energy decreases. Sufficient dressing is very essential in limiting the width of the molten zone to few micrometers. As a result, it was found that local melting at contact spots to be a rather common mechanism during grinding of superalloys, lead to so-called white layers which can easily be observed on metallographic cross sections.