Synthesis of MoSi2-TiC nanocomposite powder via mechanical alloying and subsequent annealing

MoSi₂-30 wt.% TiC nanocomposite powder was successfully synthesized by ball milling and following heat treatment. Effect of milling time and annealing temperature were investigated. The products synthesis and reactions progress were characterized by XRD. Morphology and microstructure of milled powders were monitored by SEM and TEM, respectively. Results showed that the synthesis of this composite begins after 10 h of milling and progresses gradually up to 30 h of milling. MoSi₂-TiC composite was completely synthesized after annealing of 30 h milled powder at 900 °C. On the basis of Reitveld refinement method, the mean grain size and microstrain of 13.2 nm and 0.44% were obtained, respectively for 30 h milled powder that is in consistent with TEM image. In the spite of grain growth and strain release, this nanocomposite powder maintained its nanostructure after annealing.     

Effect of waste serpentine on the properties of basic insulating refractories

Basic insulating refractories were fabricated by the pressing route using dead-burned magnesia, pure calcined alumina, expanded perlite, and calcined waste serpentine as starting raw materials in four compositions from F1 to F4. Periclase and forsterite were major phases in F1 and F2 compositions, while spinel was also detected in the XRD patterns of F3 and F4 samples. Quantitative phase analysis showed that F4 sample sintered at 1450?°C has the highest forsterite content among all other samples. On the other hand, it has lower thermal conductivity compared to F1 to F3, and even lower than aluminosilicate IFBs with the same bulk density. It is concluded that forsterite is a highly insulating material, compared to periclase, corundum, periclase-spinel, aluminosilicates, such as mullite, etc.     

Reinforcement of maleated polyethylene/ground tire rubber thermoplastic elastomers using talc and wood flour

Maleated polyethylene (MAPE)/Ground tire rubber (GTR) thermoplastic elastomer with 50 vol % GTR was reinforced by incorporation of talc powder and wood flour. Scanning electron microscopy (SEM) reveals that maleated polyethylene (MAPE) has good compatibility with wood flour, but the adhesion with talc particles is weak. Tensile moduli of MAPE/GTR increase more significantly after inclusion of talc particles compared to wood flour. Prediction of the tensile modulus of hybrid MAPE/GTR/particle composites is successfully performed using a combination of Kerner and Halpin‐Tsai models. Elastic moduli are shown to depend strongly on both aspect ratio and level of particle dispersion in the matrix. Measurement of compression sets shows that elastic recovery of the compounds decreases after addition of solid particles. Samples having better particles/matrix compatibility show higher elastic recovery. Thermogravimetric analysis shows that inclusion of wood flour decreases thermal stability of compounds. Density and hardness of MAPE/GTR are also shown to increase after inclusion of particulate reinforcements. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40195.     

CEDAR: Modeling impact of component error derating and read frequency on system-level vulnerability in high-performance processors

Reliability of the current microprocessor technology is seriously challenged by radiation-induced soft errors. Accurate Vulnerability Factor (VF) modeling of system components is crucial in designing cost-effective protection schemes in high-performance processors. Although Statistical Fault Injection (SFI) techniques can be used to provide relatively accurate VF estimations, they are often very time-consuming. Unlike SFI techniques, recently proposed analytical models can be used to compute VF in a timely fashion. However, VFs computed by such models are inaccurate as the system-level impact of soft errors is overlooked.     

Scattering of Dirac electrons by a random array of magnetic flux tubes

The scattering of two-dimensional (2D) massless electrons as presented in graphene in the presence of a random array of circular magnetic flux tubes is investigated. The momentum relaxation time and the Hall factor are obtained using optical theorem techniques for scattering. Electrons with energy close to those of the Landau levels of the flux tubes exhibit resonant scattering and have a long life-time to reside inside the magnetic flux tube. These resonances appear as sharp structures in the Hall factor and the magneto-resistance.     

Piperazine and methyldiethanolamine interrelationships in CO2 absorption by aqueous amine mixtures. Part II—Saturation rates of mixed reagent solutions

This work is a companion to a previous article, Part I, published in The Canadian Journal of Chemical Engineering, dealing with CO₂ absorption in aqueous solutions containing a single aminic reagent (specifically methyldiethanolamine (MDEA) or piperazine (PZ)). In this second part, different PZ/MDEA mixtures are experimentally studied and their performances are compared with that of the single reagents. It is indeed well known that small quantities of PZ added to MDEA aqueous solutions are sufficient to obtain a significant improvement in the kinetics of the process. PZ is considered an activator or promoter for MDEA, but the mechanism of this synergy has still not been clearly demonstrated. The aim of this study is an attempt to understand how PZ and MDEA can interact by experimentally analyzing this beneficial mutual effect and by explaining it with the help of a suitable yet not complex model. We believe that the involved chemistry is not more complex than that reported in Part I for the single reagents. According to our findings, it is MDEA that enhances the action of PZ, as opposed to what many authors claim. Moreover, our results seem to rule out the existence of any PZ shuttle effect.     

In situ emulsion polymerization and characterization of PVAc nanocomposites including colloidal silica nanoparticles for wood specimens bonding

Polyvinyl acetate (PVAc) nanocomposites for wood adhesives containing different amounts of colloidal silica nanoparticles (CSNs) were synthesized via in situ one-step emulsion polymerization. The adhesion strength of wood specimens bonded by PVAc nanocomposites was investigated by the tensile test. Thermal properties of PVAc nanocomposites were also characterized by differential scanning calorimetry and thermogravimetric analysis. Rheological and morphological properties of the PVAc nanocomposites were investigated using rheometric mechanical spectrometry and field emission scanning electron microscopy (FESEM), respectively. The obtaining results showed that the shear strength of PVAc nanocomposite including 1 wt. % CSNs has the highest shear and tensile strength about 4.7 and 3.2 MPa, respectively. A small increment of T_g (~3 °C) and considerable increment of the ash content proved the enhancement of PVAc thermal characterization in the presence of CSNs. FESEM results showed uniform dispersion of nanoparticles throughout the PVAc matrix due to using the in situ emulsion polymerization process. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2020 , 137, 48570.     

A simple and convenient method for the surface coating of TiO2 nanoparticles with bioactive chiral diacids containing different amino acids as the coupling agent

For practical applications, especially in an organic-solution situation, the surface of TiO₂ nanoparticles (NP)s requires modification with an organic coupling agent. Therefore, in this study, the surface of TiO₂ NPs with average diameter of 30 nm was modified with bioactive dicarboxylic acids (DA)s containing different natural amino acids such as l-valine, l-methionine, l-leucine, and l-isoleucine. The prepared DAs-modified TiO₂ NPs were studied with Fourier transform infrared spectroscopy, X-ray diffraction, field emission scanning electron microscopy, transmission electron microscopy and thermogravimetric analysis techniques. The results showed that the modifiers were grafted on the surface of TiO₂ NPs. Modified TiO₂ NPs could be environmentally friendly due to the presence of bioactive DAs.     

Modified Cuckoo Optimization Algorithm (MCOA) to solve Precedence Constrained Sequencing Problem (PCSP)

In recent years, new meta-heuristic algorithms have been developed to solve optimization problems. Recently-introduced Cuckoo Optimization Algorithm (COA) has proven its excellent performance to solve different optimization problems. Precedence Constrained Sequencing Problem (PCSP) is related to locating the optimal sequence with the shortest traveling time among all feasible sequences. The problem is motivated by applications in networks, scheduling, project management, logistics, assembly flow and routing. Regarding numerous practical applications of PCSP, it can be asserted that PCSP is a useful tool for a variety of industrial planning and scheduling problems. However it can also be seen that the most approaches may not solve various types of PCSPs and in related papers considering definite conditions, a model is determined and solved. In this paper a new approach is presented for solving various types of PCSPs based on COA. Since COA at first was introduced to solve continuous optimization problems, in order to demonstrate the application of COA to find the optimal sequence of the PCSP, some proposed schemes have been applied in this paper with modifications in operators of the basic COA. In fact due to the discrete nature and characteristics of the PCSP, the basic COA should be modified to solve PSCPs. To evaluate the performance of the proposed algorithm, at first, an applied single machine scheduling problem from the literature that can be formulated as a PCSP and has optimal solution is described and solved. Then, several PCSP instances with different sizes from the literature that do not have optimal solutions are solved and results are compared to the algorithms of the literature. Computational results show that the proposed algorithm has better performance compared to presented well-known meta-heuristic algorithms presented to solve various types of PCSPs so far.     

Incorporating Nano-silica as a Binder to Improve Corrosion Resistance of High Alumina Refractory Castables

In this study, four types of castables as calcium-aluminate cement (CAC)-bonded and nano-silica (NS)-bonded castables based on tabular-alumina and bauxite aggregates were prepared to investigate the replacement of the calcium-aluminate cement by NS. All samples were allowed to dry at 110 °C then fired at 800 and 1200 °C. Bulk density and apparent porosity of samples were measured. The molten aluminum static corrosion test (cup test) results showed that NS-bonded specimens had higher resistance to corrosion compared to CAC-bonded samples (based on the measured average aluminum penetration depth into the refractory texture). However no penetration was observed in bauxite NS-bonded samples. The results were consistent with dynamic corrosion test in aluminum melt carried out at 800 °C for 100 h. The small pore size in NS-bonded castables was found to be the main cause for high corrosion resistance as micro-pores prevented the melt to penetrate into the refractory.