New balance ground relay for parallel four-circuit transmission lines

A 66-kV network generally is grounded through a neutral grounding resistor. In this network a single-phase ground-fault current is limited to as small as 100 to 400 A. There are parallel four-circuit transmission lines mounted on the same tower in the 66-kV network. In such transmission lines, the load and the fault currents could induce circulating current that flows through the lines. Since the circulating current has zero-phase-sequence and negative-phase-sequence components, it could cause unwanted operation of a balance ground relay using zero-phase-sequence current. However, it is difficult to compensate for the circulating current by the conventional vector compensation scheme. This paper presents a new balance ground relay to deal with the circulating current. In the relay from the ground-fault inception until first tripping, the difference current Δ3I_2d of negative-phase-sequence current 3I_2d of the differential current between two protected lines is used as an input current. The Δ3I_2d is the difference current of 3I_2d between, before and during faults. After the first tripping, the difference current of positive-phase-sequence load current and zero-phase-sequence current of the forementioned differential current are used as an input current. Consequently, a higher sensitivity of the ground-fault protection for these lines has been achieved. The correct operation of the new balance ground relay was confirmed when a single-phase-ground-fault occurred in the parallel four-circuit transmission lines, to which the relay is applied.     

Improvement of emission efficiency in polymer light-emitting devices based on phosphorescent polymers

We report improvement of emission efficiency in polymer light-emitting devices (PLEDs) employing phosphorescent polymers. A hole-blocking layer was inserted between the emissive layer and the cathode to enhance recombination efficiency for the injected holes and electrons. Aluminum(III)bis(2-methyl-8-quinolinato)4-phenylphenolato (BAlq) was used for the hole-blocking layer. The resultant PLEDs exhibited significant improvement of emission efficiency. The respective external quantum efficiencies for red, green and blue PLEDs were 6.6, 11 and 6.9%. These values are very high compared with those based on conventional fluorescent polymers.     

Twin-Related Tetragonal Variants in Yttria Partially Stabilized Zirconia

Crystals of yttria partially stabilized zirconia were grown by the arc-image floating-zone technique and studied by transmission electron microscopy. Crystals annealed at 1700°C consist of tetragonal precipitates and a cubic matrix. The platelike domains in a precipitate are twin-related tetragonal variants stacked alternately parallel to the (011) twin plane. The axial relations between the tetragonal precipitate and the cubic matrix are [100]_tetragonal|[100]_cubic, [011]_tetragonal|[011]_cubic.     

Effect of Silicon Dioxide on the Thermal Diffusivity of Aluminum Nitride Ceramics

The thermal diffusivity of AlN ceramics was significantly decreased by the addition of SiO₂. The AlN ceramics with 4 wt% SiO₂ could not be densified by pressureless sintering in the temperature range 1400° to 1800°C. The thermal diffusivity of these samples was very low because of their porous structure. The AlN ceramics containing 2, 4, and 8 wt% SiO₂ were densified by hot-pressing and also had low thermal diffusivity. In these samples, the grains of the 27R polytype that resulted from the reaction between AlN and SiO₂ were dispersed, obstructing the conduction of heat. The relation between the amount of 27R polytype and the thermal diffusivity of the AlN ceramics was determined.     

Unperturbed dimension of poly(4-acetoxystyrene) measured in good and theta solvents

In order to obtain the additional data concerning the unperturbed dimension of poly-4-substituted styrene, light scattering measurements are performed on the twenty-two fractions with molecular weight of (0.91–352)·10⁴ of poly(4-acetoxystyrene) in dioxan at 25°C, from which the molecular weight obtained was found easily to be evaluated with the gel permeation chromatography using THF. Phase separation experiments for this polymer indicate that the theta state is attained in isopropyl acetate at 19.7°C and butyl acetate at 26.8°C. By making viscosity measurements at that state, the value of K_Θ is directly evaluated as 5.4·10^?4 dl g^?1. The limiting viscosity number is also obtained in good solvents, THF and dioxan, at 25°C and constants of the Mark-Houwink-Sakurada equation in each solvent are determined. Further, approximately the same K_Θ as above is obtained from these data with the Stockmayer-Fixman plot. The calculated value of steric factor, 2.37, on this polymer may be plausible, compared with those of polyvinylaromatic derivatives.     

Formation of alkaline scale in heating brine obtained by the ion-exchange membrane method

Electrodialysis with ion-exchange membranes is one of the most important methods of desalination and salt manufacture. Prevention of scale formation in dialysis cells and evaporators is one of its main problems.This paper discusses the formation of alkaline scale during the process of heating and concentrating brine obtained by electrodialysis with ion-exchange membranes.     

Molded micro- and mesoporous carbon/silica composite from rice husk and beet sugar

A molded carbon/silica composite with high micro- and mesoporosity, as well as a high bulk density, was fabricated by activating a disk-molded precursor made from carbonized rice husk (RH) and beet sugar (BS) at 875 °C in CO₂. The pore structure of the RH- and BS-based carbon/silica composite (RBC) was analysed in relation to the bulk density. An activation time of 2.0 h provided the largest BET specific surface area (1027 m²/g) and total pore volume (0.68 cm³/g) and a low bulk density (0.54 g/cm³). An RBC that was first activated for 1 h was immersed again in BS syrup and then activated in CO₂ for 1 h. This two-step activation process provided both a high bulk density (0.69 g/cm³) and a highly textured structure (BET specific surface area, 943 m²/g; total pore volume, 0.56 cm³/g). The immersion in BS syrup was useful for improving the texture without reducing the bulk density, in comparison to one-step activation for 1.0 h. The suspension of the RBCs was basic because of the residual inorganic compounds of potassium and calcium. However, the basicity of the suspension was alleviated by washing the RBCs with water.     

Seismic proof test of a reinforced concrete containment vessel (RCCV): Part 2: Results of shaking table tests

A 1/8-scale model was constructed of a reinforced concrete containment vessel (RCCV) used in the latest advanced boiling water reactors (ABWR). Shaking table tests were conducted on it with input motions corresponding to or exceeding a design earthquake assumed for a real Nuclear Power Plant.The objectives of the tests were to verify the structural integrity and the leak-proof functional soundness of the RCCV subjected to design earthquakes, and to determine the ultimate strength and seismic margin by an excitation that led to the model's collapse. The model, the test sequence and the pressure and leak test results were addressed in Part 1. The shaking table test method, the input motions and the test results, including the transition of the model's stiffness, natural frequencies and damping factors and the effects of vertical input motions and internal pressure on the model's characteristics and behavior, the load–deformation, the ultimate strength, the failure mode of the reinforced concrete portion and the liner plate are described here. The seismic safety margin that was evaluated by the energy input during the failure test to a design basis earthquake will be described in Part 3. The analytical results of simulation using the multi-lumped mass model will be described in Part 4.     

Boiling heat transfer of HFO-1234yf flowing in a smooth small-diameter horizontal tube

The flow boiling heat transfer coefficient of the low-GWP (global warming potential) refrigerant HFO-1234yf inside a smooth small-diameter horizontal tube (inner diameter: 2 mm) was experimentally investigated. The local heat transfer coefficient was measured at heat fluxes of 6-24 kW m⁻², mass fluxes of 100-400 kg m⁻² s⁻¹, an evaporating temperature of 288.15 K, and an inlet vapor quality of 0-0.25. The results show that the effect of heat flux on the heat transfer was large at low vapor quality, while the effect of mass flux was large at high vapor quality. The heat transfer coefficient of HFO-1234yf was almost the same as that of R-134a. The heat transfer coefficients calculated based on correlations with Saitoh et al. agreed well with the measured values compared to other correlations. The measured pressure drop agreed well with that predicted by the Lockhart-Martinelli correlation.     

强夯加固饱和软粘土的几个问题探讨

根据最近用强夯加固饱和软粘土的经验,探讨了下列几个问题:用现场试验法确定夯击参数与饱和软粘土的加固效果。饱和软粘土在强夯后的渗透性。它基本符合西德鲁尔大学提出的公式V=Ki~m。根据荷载大小、种类、范围,地基土壤特性及建筑物类型,提出了超夯范围。强夯振动对附近建筑物的影响及减振措施。建议按频率分析法考虑对附近建筑物的影响。