Conditions and costs for renewables electricity grid connection: Examples in Europe

This paper compares conditions and costs for RES-E grid connection in selected European countries. These are Germany, the Netherlands, the United Kingdom, Sweden, Austria, Lithuania and Slovenia. Country specific case studies are presented for wind onshore and offshore, biomass and photovoltaic power systems, as based on literature reviews and stakeholder interviews. It is shown that, especially for wind offshore, the allocation of grid connection costs can form a significant barrier for the installation of new RES-E generation if the developer has to bear all such costs. If energy policy makers want to reduce the barriers for new large-scale RES-E deployment, then it is concluded that the grid connection costs should be covered by the respective grid operator. These costs may then be recouped by increasing consumer tariffs for the use of the grid.     

Removal of free and complexed heavy-metal ions by sorbents produced from fly (Musca domestica) larva shells

Fly larva shells (FLS) are formed as a side product in the biological treatment of organic wastes, and chitin and chitosan produced from the FLS have been used as sorbents for heavy-metal ions. Sorbents are characterised by FT-IR measurements and pH-potentiometric titration and by determination of their surface area, and the content of main elements (C, N, P, S) and ashes. Free metal ions are sorbed best (up to 0.5-0.8 mmol g(-1)) onto chitin and chitosan. The sorption ability for free metal ions of chitin decreases in the order Fe(III) > Cu(II) (Pb(II) > Zn(II). > Ni(II) > Mn(II) and that of chitosan decreases in the order Cu(II) > Mn(II) > Ni(II) > Zn(II) > Pb(II) > Fe(III). The complexed metal ions are sorbed by the FLS up to 0.2-0.4mmol g(-1). The sorption ability for metal ions and ligands depends on pH, concentration of complexed metal ions and the ligand species in the solution. Glycine has the retarding effect on the sorption of Ni(II) and Cu(II) ions, and EDTA enhances the Cu(II) ion sorption. Ni(II) and glycine sorption obeyed the Langmuir isotherm. The observed sorption data show the promising potentialities of the FLS for the heavy-metal removal from the solutions, containing strong complexing agents. Mechanisms for the removal of free and complexed metal ions by chitin, chitosan and the FLS have been discussed.     

Nanocomposite films and coatings produced by interaction between graphite oxide and Congo red

Nanocomposite films and coatings were produced from the aqueous solutions containing different proportions of graphite oxide (GO) and Congo red by filtering through a polycarbonate membrane filter into alkaline media. They were examined by electron microscopy, Raman and FTIR spectroscopy, XRD, contact angle, and electrical conductivity measurements. It was established that the Congo red is able to interact through its amino groups with different functional groups of GO to form larger moieties composed of the nanoplatelets of GO. Raman spectroscopy revealed quinoid-like ring structure for dye adhering to the GO. In the case when the interaction occurs with the terminal functional groups located on the edges of the nanoplateletes of GO, larger crystallites in the nanocomposite are formed. The interaction between the Congo red and functional groups of GO situated in a basal plane leads to more compact structure of the nanocomposite. Pulsed laser treatment was used to reduce GO to graphene. Raman spectra of laser treated areas show positive effect of addition of the Congo red on the graphene yield in nanocomposite coatings after the laser treatment.     

Hydrogen influence on mechanical and fracture mechanics characteristics of zirconium Zr–2.5Nb alloy at ambient and elevated temperatures

This article deals with the investigation of the hydrogen concentration and temperature influence onto mechanical and fracture mechanics characteristics of RBMK-1500 Ignalina NPP unit 2 reactor fuel channel material—Zr–2.5Nb zirconium alloy (TMT-2) at temperatures from ambient up to 300 °C. The investigation of mechanical characteristics was performed on tensile specimens, fracture mechanics characteristics K_Q, , J_IC—on compact specimens (B = 4 mm) of hydrogen-free and saturated by hydrogen (52, 100 and 140 ppm) at 20, 170, 200 and 300 °C. The investigation showed that temperature increasing calls mechanical strength decreasing, whereas the reductions of area increase. Stronger influence of hydrogen concentration onto mechanical characteristics is noticed only at 20–170 °C temperature, however this influence diminishes as the temperature increases and weakest hydrogen influence is given at 300 °C. Fracture toughness characteristics K_Q, more depends on temperature than on hydrogen concentration. Critical J_IC integral values for the specimens containing hydrogen were given lowest at 20 °C, increases when temperature were raised up to 140 °C and were given highest when it reaches 300 °C.The analysis of and J_IC dependence due to the mechanical characteristics of zirconium alloy has showed that the modified plasticity Z_mod = (R_p0.2/R_m)Z satisfactorily approximates the influence of temperature and hydrogen concentration on variation of these characteristics.     

Dependence of ceramics physical–mechanical properties on chemical and mineralogical composition

To determine the dependence of physical–mechanical properties of ceramics on chemical and mineralogical composition, the appropriate raw materials have been tested and five batches of ceramic specimens have been formed. The aforementioned specimens have been made of the following components: fusible clay, quartz sand, chamotte, sawdust and crushed window glass. The specimens differed by the amount of the components (differences in burning regime were insignificant). After having formed and burned the specimens, their X-ray phase analysis has been carried out, elemental chemical composition has been defined and the composition of chemical oxides has been calculated. Moreover, the following physical–mechanical properties have been determined: density, general contraction and compressive strength. The test results showed that the physical–mechanical properties of ceramics mostly depend on the amount carbon, silicon and aluminum. The mineralogical structure of specimens under testing was practically unchanged.     

Sustainability assessment for recreational buildings

A large amount of natural resources and energy is wasted during and after the building construction process which might cause environmental problems such as climate changes. In order to achieve higher standards of environmental protection a range of building assessment systems has been established. However, they are mostly connected with the efficiency of an environmental protection and consumption of resources. Only few of them have limited possibilities to assess social and economic sustainability. A sustainable building includes aspects of environment, economy and society and therefore requirements to its assessment systems should be complex. We suggest that sustainability principles, that is, environmental, social and economic sustainability, should be estimated in the same equal weightings. The authors of this article created a model for assessing the sustainability for recreational buildings. Our model was created, in collaboration with experts, using breakdown, compensation and the analytic hierarchy process methods. The sustainability of Druskininkai Snow Arena (Lithuania) was assessed using a sustainability assessment system based on the proposed model.     

The Nobel prize in physics - regularities and tendencies

Various distributions of the Nobel laureates in physics in the 20th century and their discoveries are considered. It is shown that the time-interval between the discovery and its recognition can be approximately described by a lognormal distribution. The ratio of the numbers of laureates awarded for the experimental and the theoretical discoveries was rather different in various decades; this was determined by some “waves” of discoveries and in the initial period probably by some subjective factors. The probability to obtain this prize for the theorist is larger than for the experimenter. The main part of the awards was given to the scientists working in the main fields of modern physics: small distances and solid state physics. Some fields of physics such as mathematical physics, relativity, statistical physics were ignored completely. The worrying tendency of an increasing average age of laureates towards their retirement age is indicated. This revised version was published online in June 2006 with corrections to the Cover Date.     

Half a century of reinforced concrete electric poles maintenance: inspection,field-testing,and performance assessment

Application of reinforced concrete (RC) poles as overhead electrical transmission line supports has become of great interest during recent years worldwide. The higher strength, longer life, and the potential to span longer distances than steel poles are the key reasons behind this tendency. A great variety of architectural shapes, relatively low maintenance costs, and high electrical resistance make RC a prominent alternative to steel. The drawbacks related to the application of RC poles include the high self-weight and vulnerability to damage. Self-weight might be reduced by prestressing the reinforcement and/or forming a tubular structure for the poles. However, both of these options might increase the vulnerability of the supports. Moreover, long-term processes (deterioration of concrete and corrosion of steel reinforcement) complicate the prediction of structural properties. This paper presents results of the everlasting inspection of the overhead electric power distribution system in Lithuania: technical state of more than 500 RC supports was assessed; selected poles were tested until failure. A specific point of this research is that most of the inspected supports were under maintenance since the middle of last century. The inspection results were used for developing the technical condition of RC pole evaluation scale proposed in this paper.     

Fracture toughness of welded joints materials for main pipelines at Ignalina NPP

This paper deals with an investigation of mechanical and fracture toughness characteristics of welded joint materials used in Ignalina Nuclear Power Plant (NPP) reactor main circulating circuit (MCC) and steam pipelines. Basic metal of MCC group distributing header (GDH) steel 08Ch18N10T (Du-300), its weld metal welded by manual and automatic arc method using the wire SV-04Ch19N11M3 and electrodes EA-100/10U or EA-100/10T, this joint heat-affected zone metal and base metal of the main steam system—steel 16GS (DU-630) and its weld metal welded by manual arc method using the wire SV-08GS2 and electrodes UONI-13/55 were tested.Mechanical properties of welded joints materials—proportional limit (σ_pl), yield (σ_y) and ultimate (σ_u) strength, fracture stress (σ_f) and ductility (Z) (percent reduction of area) of the specimens were determined. Investigation of relative critical stress intensity factor for fixed thickness of the specimen and critical J-integral, J_IC, was performed.The probabilistic investigation of influence of the mechanical properties (σ_pl, σ_y, σ_u) onto fracture toughness characteristics and J_IC for tested materials by using linear regression model with three independent variables was performed.Research enabled to conclude that proposed multivariable regression model with 80% probability (confidence coefficient α = 0.05) has explained reasonably well the dependence of with σ_pl, σ_y, σ_u and it has shown the non-acceptability of probabilistic evaluation of the model with respect to J_IC.