Theoretical and Experimental Study of Water Transport in a Hollow Cylinder Applied to the Drying of Round Squid Mantle

Until now, attention has been focused solely in the drying of squid mantle from an experimental point of view, neglecting the transport phenomenon studies of water in squid muscle. This work studies the drying of squid mantle (Loligo brasiliensis), previously salted and smoked by liquid smoking (hickory extract), using a tubular dryer in closed cycle with a silicagel fixed bed in series. The mass transfer phenomenon during drying was studied, based on the Fick's second law, with the effective diffusivity supposed constant, which enabled an analytical solution to the problem. The drying curve calculated with the resulting equation was compared with experimental data. The model was applied to a hollow cylinder geometry (round squid mantle), with its internal surface isolated from the drying environment by a plastic film. The latter was given a tubular form and introduced inside the mantle cavity (impervious wall boundary condition).     

Interaction of protein percent with caloric density and protein source for lactating cows

Experiment 1 was to test effect of three ratios of energy to protein in complete mixed diets for 36 lactating cows in three, 28-d periods. Energy was varied with cottonseed hulls, pelleted ground corrugated boxes, and a mixture of the two. Crude protein was varied with soybean meal to give energy:crude protein of 5.7, 5.0, and 4.6 for each energy amount. Cottonseed meal was compared with soybean meal in corrugated box diets. Feed intake was much higher with cottonseed hulls, and appreciable feedlot bloat resulted from pelleted ground corrugated box diets. Data adjusted to equal feed intake showed significant effect of energy to crude protein ratio on milk yield and improved digestion of organic matter with soybean meal vs. cottonseed meal. Experiment 2 tested the hypothesis that lactating cows consuming high-protein alfalfa may benefit from supplemental protein. Diets were 50% forage. Six diets were 14 or 18% crude protein in three ratios of alfalfa hay to corn silage (0:100, 50:50, 100:0). Additional corn silage diets were to compare: 14 versus 18% protein from distiller's dried grains with solubles only and with .5 or .9% urea (four diets); two 14% protein diets compared .6% added potassium chloride with or without .5% urea. Thirty-six Holstein cows in early lactation received one of the 12 diets in each of three 28-d periods. Distiller's grains with solubles markedly depressed milk yield (2.2 kg/d) and milk protein (.22%); heat damage of distiller's grains was evident. Protein interacted with alfalfa so gain in milk from 18 versus 14% increased from .55 to 1.36 to 2.66 kg/d as alfalfa changed from 0 to 50 to 100%. Thus, crude protein of alfalfa was not as effective as that from soybean meal in supporting milk yield.     

The molecular biology of bladder carcinoma

OBJECTIVE: The clinical course of transitional cell carcinoma of the bladder can be difficult to predict due to its potential to invade the muscle layer and/or develop to a high grade lesion. Bladder carcinoma can arise from genetic changes that may activate the oncogenes (-c-erbB2, c-erbB1, c-myc, ras, etc.) and/or inactivate the suppressor genes (p53, Rb). The aim of the present study is to continue a study protocol on the molecular biology of bladder tumors. METHODS/RESULTS: From January, 1993 to January, 1995, 85 patients were studied. These patients were divided into two groups: the first group comprised 14 controls of urothelial tissue and the second comprised 65 cases of transitional cell carcinoma of the bladder. p53 expression was determined by an immunohistochemical method (NCL-p53-DO7 monoclonal antibody). Quantification of the p8 oncoprotein in cytosol and EGFR (epidermal growth factor receptor) in membrane was performed by ELISA (Oncogene Science) and RIA (Vienna Lab), respectively. A statistically significant relationship between the expression of p53 and EGFR with tumor stage and grade was found. Quantification of p185 and EGFR showed higher values in the tumor tissue than in the control samples, but a worse survival could not be determined. CONCLUSIONS: The present study shows that p53 expression can be considered to be a prognostic factor. It provides useful information on the aggressive behaviour of the tumor and has a direct relation with the survival rates.     

Sheet molding compound characterization using spiral flow

Sheet molding compound (SMC) is a fiber‐reinforced polymeric composite. It is often used in automotive, marine, and industrial applications over other materials because of its high strength to density ratio, resistance to corrosion, and low cost. There is a demand in the SMC industry to be able to characterize SMC processability. This is particularly true for heavy truck body panels, one of the fastest growing applications of SMC. Because of their large size and high strength requirement, the molding forces have a major influence in the molding cycle. Also because of the long flow paths involved, the ability of the paste to carry glass needs to be properly characterized when developing new SMC materials. In this article, we demonstrate the benefits of using spiral flow as a processability tester. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Characterization of CuInS2 thin films for solar cells prepared by spray pyrolysis

We have made a study of the chemical composition, the electrical, the optical and the structural properties of polycrystalline CuInS₂ thin films prepared by spray pyrolysis to be used for thin film solar cells. These films were deposited starting from aqueous solutions with different chemical compositions ([Cu]/[In] and [S]/[Cu] ratios) and at different substrate temperatures. In all cases, the material is p-type with grains preferentially oriented in the (112) direction of the sphalerite structure. The electro-optical properties show a very strong dependence on the [Cu]/[In] ratio in the solution. Films with copper excess have smaller resistivity and better crystallinity than those which are stoichiometric or have indium excess. The results obtained in this work show the possibility of having CuInS₂ thin films with a wide range of resistivity, a fact that could be important for making solar cells based on this material.     

Development of an RVE using a DEM–FEM scheme under modified approximate periodic boundary condition to estimate the elastic mechanical properties of open foams

Engineering with Computers - In this article, a methodology based on Discrete Element Method (DEM) and Finite Elements Method (FEM) combined with modified Approximate Periodic Boundary Condition...     

GPU accelerated waterpixel algorithm for superpixel segmentation of hyperspectral images

The Journal of Supercomputing - The high computational cost of the superpixel segmentation algorithms for hyperspectral remote sensing images makes them ideal candidates for parallel computation....     

An approach to reduce energy consumption and performance losses on heterogeneous servers using power capping

Journal of Scheduling - Rapid growth of demand for remote computational power, along with high energy costs and infrastructure limits, has led to treating power usage as a primary constraint in...     

Performance control for interconnection of identical systems: Application to PLL network design

In this paper, the problem of the control law design for interconnected identical systems ensuring the global stability and the global performance properties is under consideration. Inspired by the decentralized control law design methodology using the dissipativity input–output approach, the problem is reduced to the problem of satisfying two conditions: (i) the condition on the interconnection and (ii) the condition on the local subsystem dynamics. Both problems are efficiently solved applying a (quasi‐) convex LMI optimization and standard H_∞ synthesis. The proposed design methodology is applied to the control law design of a synchronous PLL network. Copyright © 2014 John Wiley & Sons, Ltd.     

Variational Foundations and Generalized Unified Theory of RVE-Based Multiscale Models

A unified variational theory is proposed for a general class of multiscale models based on the concept of Representative Volume Element. The entire theory lies on three fundamental principles: (1) kinematical admissibility, whereby the macro- and micro-scale kinematics are defined and linked in a physically meaningful way; (2) duality, through which the natures of the force- and stress-like quantities are uniquely identified as the duals (power-conjugates) of the adopted kinematical variables; and (3) the Principle of Multiscale Virtual Power, a generalization of the well-known Hill-Mandel Principle of Macrohomogeneity, from which equilibrium equations and homogenization relations for the force- and stress-like quantities are unequivocally obtained by straightforward variational arguments. The proposed theory provides a clear, logically-structured framework within which existing formulations can be rationally justified and new, more general multiscale models can be rigorously derived in well-defined steps. Its generality allows the treatment of problems involving phenomena as diverse as dynamics, higher order strain effects, material failure with kinematical discontinuities, fluid mechanics and coupled multi-physics. This is illustrated in a number of examples where a range of models is systematically derived by following the same steps. Due to the variational basis of the theory, the format in which derived models are presented is naturally well suited for discretization by finite element-based or related methods of numerical approximation. Numerical examples illustrate the use of resulting models, including a non-conventional failure-oriented model with discontinuous kinematics, in practical computations.