An optically clocked transistor array with dual serial-to-parallel and parallel-to-serial conversion capability for optical label swapping

We propose an optically clocked transistor array optoelectronic integrated circuit (OEIC) for both serial-to-parallel and parallel-to-serial conversion (demux/mux), enabling an interface between high-speed asynchronous burst optical labels and CMOS circuitry for optical label swapping. Dual functionality of the OEIC reduces size, power, and cost of the optical label swapper. The capability for greater than 20-Gb/s conversion operation is demonstrated.     

Impact of crosstalk in an arrayed-waveguide multiplexer onN×N optical interconnection

The impact of crosstalk in an arrayed-waveguide N×N wavelength multiplexer is investigated precisely in relation to its application to wavelength-routing N×N all optical networks. In such systems multiple crosstalk light which has the same wavelength as the signal results in signal-crosstalk beat noise. We confirm that the noise is Gaussian and obtain the relation between crosstalk and power penalty. It is shown that the crosstalk must be less than -38 dB for a 16×16 system to keep the power penalty below 1 dB at a bit error rate of 10^-9     

Digitally tunable optical filters using arrayed-waveguide grating(AWG) multiplexers and optical switches

Two novel configurations for digitally tunable optical filters based on arrayed-waveguide grating (AWG) multiplexers are described in detail with emphasis on the connection of the AWG multiplexer and optical switches. Performance comparisons show that conventional configurations are disadvantaged by the switch size required and loss imbalance among the optical frequency-division-multiplexed (FDM) channels; the proposed configurations require only O(√(N)) switch elements to select one of N FDM channels, and the loss imbalance is lower by up to 75% in decibel     

Effect of Milling on Slip Casting of Partially Stabilized Zirconia

Specimens of partially stabilized zirconia were slip cast from aqueous suspensions and sintered at 1500°C for 3 h. The relative density of the cast specimens and the firing shrinkage of the sintered specimens depend on the milling time for the suspension. Vickers hardness and K_IC values of 11.46±s0.07 GN/m² and 6.10 ±0.04 MN.m^3/2, respectively, were obtained for all sintered specimens. The dispersion of the suspension is important in increasing the relative density of the cast specimens.     

Numerical evaluation of three-dimensional water impact by the displacement potential formulation

The numerical accuracy of the displacement potential approach for a three-dimensional water-impact problem is investigated. An examination of the elliptic paraboloid shows that the boundary-value problem for the displacement potential, as well as the velocity potential, can be solved accurately, even if the panel size of the numerical scheme is no small enough. The numerical accuracy of the position of the contact line is poor. However, the accuracy of the virtual mass is good because of the averaging effect along the contact line. A comparison with Scolan and Korobkin's designed body confirms the accuracy of the drop speed and the penetration displacement. The displacement potential approach is extended to the case of water impact with trapped air. The numerical accuracy of the calculated air pressure in the cavity is confirmed by comparison with an experimental result. With these results, the suitability of the displacement potential approach to the ship-slamming problem is demonstrated.     

Breakdown of oil films and formation of residual films

The breakdown processes of oil films under quasi-static loading have been investigated by using a newly developed steel-oil-mercury system. The relationship between the thickness and breakdown ratio of a hexadecane film is represented by a single master curve independently of the indentation speed, indentation load, and temperature. The master curve shows that the breakdown process of hexadecane includes two stages; one is the decrement of the thickness without breakdown and the other is the decrement of the thickness with a drastic progress of breakdown. By solving a small amount of fatty acid in hexadecane, the thickness increases and the breakdown ratio decreases noticeably; a multilayer residual film supporting normal load is formed between two metal surfaces. Experiments at different temperatures reveal a negative relationship between the temperature and thickness of residual film, which indicates that the residual film is organized by physical interaction rather than chemical interaction. At least under a lower concentration, the residual film appears to consist of not only fatty acid molecules but also hexadecane molecules.